alarm MITSUBISHI OUTLANDER SPORT 2014 3.G User Guide

Indicator lamp, warning lamp, and information screen display list
Instruments and controls 6-29
6
zThe outside temperature is 3 °C (37 °F) or less.
zBe careful of ice on the road.zThe road can be icy even when this warn-ing is not displayed, so drive carefully.
zThe Adaptive Cruise Control System (ACC) has detected the approach of the vehicles in front.
zIncrease the following distance by depress-ing the brake pedal or marking other decel-erating control.Refer to “Adaptive Cruise Control System (ACC): Proximity alarm” on page 7-46.
zThe Forward Collision Mitigation System (FCM) has detected the danger of collision.
zTa k e a p p r o p r i a t e a c t i o n s u c h a s d e p r e s s i n g the brake to avoid collision.Refer to “FCM braking function” on page 7-56.
zThe Adaptive Cruise Control System (ACC) detected a stop of the vehicle in front and stopped your vehicle, but the brake will be released soon.
zDepress the brake pedal as soon as your vehicle comes to a stop.Refer to “Adaptive Cruise Control System (ACC)” on page 7-43.
Screen
Cause
Solution (Reference)
BK0203201EN.book 29 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list
Instruments and controls 6-35
6
This informs you that a periodic inspection is due.
zWhen the battery save mode is activated. Refer to “Battery save switch” on page 7-22.zWhen the battery charge mode is activated. Refer to “Battery charge switch” on page 7-23.zWhen the reversing sensor system detect an obstruction.
Refer to “Reversing sensor system” on page 7-63.
zWhen the Forward Collision Mitigation System (FCM) is activated or the timing of an alarm is changed.
Refer to “FCM ON/OFF switch” on page 7-59.
zWhen the Forward Collision Mitigation System (FCM) is deactivated.
Screen
System operation status
Reference
BK0203201EN.book 35 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Acoustic Vehicle Alerting System (AVAS)
Starting and driving 7-25
7
zWhen the vehicle speed is about 3 km/h to35 km/h and engine is not running.
The sound does not start in the followingcases. zWhen the vehicle speed is about 3 km/h orless and the brake pedal is depressed.zWhen the vehicle speed is about 35 km/hor more.zWhen the select position is “P” (PARK)position.zWhen the AVAS OFF indicator in themeter is illuminating.zWhen the engine is running.
When the operation mode is set to “ON”, theAVA S O F F i n d i c a t o r c o m e s o n a n d g o e s o u tin a few seconds.
E00631701052
If the operation mode is put in ON, the AVASis automatically turned on.The AVAS should be turned on while normaldriving.When driving on the freeway etc., it is possi-ble to turn off by pressing the AVAS OFFswitch.
If pressing the AVAS OFF switch, the audiblealarm not sound and indicator lamp illumi-nates.If pressing the AVAS OFF switch once again,the AVAS is activated and the indicator lampgoes off.
WA R N I N GzEven if the Acoustic Vehicle Alerting Sys-tem (AVAS) sounds, pay special attentionto pedestrians.Pedestrians may not notice the oncomingvehicle, which may cause an accidentresulting in serious
personal
injury or
death.CAUTIONzAlways confirm the indicator lamp goes offbefore driving. If the indicator lamp blinks, the operationmode is put in OFF, and the operation modeis put in OFF once again. It is not abnormallyif the indicator lamp goes off. If the indicatorlamp blinks again, have the vehicle inspectedat a MITSUBISHI MOTORS AuthorisedService Point as
soon as possible.
AVA S O F F s w i t c h
WA R N I N GzNever turn the Acoustic Vehicle AlertingSystem (AVAS) off if there is a possibilitywhere the pedestrian exists.NOTE
zIf the operation mode is put in OFF, whilethe AVAS has been turned off, and the opera-tion mode is put in ON once again, the AVASis activated.
BK0203201EN.book 25 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*7-44 Starting and driving
7
NOTE
zYou cannot operate the regenerative brakecontrols while the adaptive cruise controlsystem (ACC) is operating. If doing so, thebuzzer sounds.zIf you turn on the adaptive cruise control(ACC) when the select position is in “B”(including B0 to B5) position, the selectposition is changed to “D” position.WA R N I N GzA driver is responsible for driving safely.Even if the ACC is in use, always graspthe surrounding circumstances and pro-vide for safe driving.zNever rely solely on the ACC. The ACC isthe system to reduce load on the driver.The ACC is not a co
llision avoidance sys-
tem or an automatic
driving system. The
system is not intended to compensate fordriver’s loss of attention to the front dur-ing driving due to distraction or careless-ness or supplement a drop in visibility dueto the rain and fog.It is never a substitute for your safe andcareful driving. Always
be ready to apply
the brakes manually.
zThis system may not correctly detect theactual situation depending on the type ofvehicle in front and
its conditions, the
weather conditions,
and the road condi-
tions.Additionally, the system may be unable todecelerate sufficiently if the vehicle infront applies the
brakes suddenly or
another vehicle cuts into your path, soyour vehicle approaches the front vehicle.Improper usage of this system or loss ofattention to the front by the over-rely onthe ACC, may result in a serious accident.CAUTIONzIn the following situations, the system maybecome transiently unable to detect a vehiclein front or triggers its control and alarmfunctions by detecting something other thana vehicle in front.•When driving in curved sections of roadincluding their entrance/outlet or runningbeside a closed lane in a traffic work orsimilar zone.WA R N I N G
•When your vehicle position in a lane isinstable, is frequently steered to right andleft, or running unstably due to a trafficaccident, trouble with some vehicles, etc.•When driving on the road that the vehicle infront runs in offset
position from your vehi-
cle.
zNever use the ACC in any of the followingsituations. Failure to follow this instructioncould lead to an accident. •On roads with heavy traffic or roads includ-ing many windings or steep curves•On roads with slippery surfaces, such asfrozen, snow-covered,
and dirt roads
•Under adverse weathe
r conditions (rain,
snow, sand storms, etc.)•On steep downslopes•On roads including steep up and downslopes or many changes in inclination•In traffic requiring frequent accelerationand deceleration•When the proximity alarm sounds fre-quently•When your vehicle is towed or your vehicletows another vehicle.CAUTION
BK0203201EN.book 44 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*7-46 Starting and driving
7
When the ACC no longer detects any vehiclein front, a buzzer sounds and the symbol ofvehicle running ahead disappears from thescreen. The vehicle is slowly accelerated toresume the set speed and continues running atthat speed.
E00634701079
While the ACC is active, if your vehicleapproaches too closely to a vehicle in frontbecause the ACC cannot allow for an ade-quate deceleration in such cases as rapid
deceleration of the vehicle in front or appari-tion of a vehicle cutting in front of your vehi-cle, the ACC gives a warning by sounding abuzzer and displaying a message.If this happens, increase the following dis-tance by depressing the brake pedal or mak-ing other decelerating control.
CAUTIONzNever leave the vehi
cle during stopping by
automatic braking.WA R N I N GzYo u r v e h i c l e m a y a c c e l e r a t e u p t o t h e s e tspeed in the following situations. Applythe brake, if necessary, to slow down.
•When your vehicle no longer follows thevehicle in front, e.g. at a freeway exit orwhen your vehicle or the vehicle in frontchanges its lane.•When driving on a curve.zIf the vehicle in fron
t turns off or changes
lane and another stationary vehicle islocated in front of that vehicle, the ACCwill not make deceleration control to thestationary vehicle.
Proximity alarm

WA R N I N G
CAUTIONzWhen the ACC is not in use, turn off the sys-tem to prevent it from operating by mistakeand an unexpected accident.zNever operate the A
CC from outside the
vehicle.zNeither control nor a warning are performedby the following situation.•Something other than vehicle such as apedestrian.•When there is abnormality in the system(When the ACC detected abnormality,“ACC SERVICE REQUIRED” is indi-cated.)
BK0203201EN.book 46 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*7-50 Starting and driving
7
There are two ways to increase the set speed.The set speed increases by 1 km/h every timeyou push up the “RES +” switch while theACC control is working. If you hold theswitch pushed up, the set speed increases in 5km/h increments.
When the accelerator pedal is depressedwhile driving with the ACC control working,you can accelerate the vehicle temporarilybeyond the presently set speed.At the point where the vehicle speed is raisedto your desired speed, push down and releasethe “SET -” switch; the new speed is then setin the system.
There are two ways to decrease the set speed.The set speed decreases by 1 km/h every timeyou push down the “SET -” switch while theACC control is working. If you hold theswitch pushed down, the set speed decreasesin increments of 5 km/h.
To i n c r e a s e t h e s e t s p e e d

By using the “RES +” switch:
NOTE
zThere is some time lag between the setting toa new speed and actually accelerating to thatspeed.zSpeed setting operation is possible even inpresence of a vehicle in front. In this case,however, the set speed alone increases with-out actual acceleration taking place.
zWhen the switch is held pushed, a buzzersounds every time the set speed changes.CAUTIONzThe setting speed should be set up the suita-ble speed according to a situation.
By using the accelerator pedal:
NOTE
CAUTIONzThe ACC braking control and proximityalarm functions will not work while theaccelerator pedal is depressed.NOTE
zThe set speed indication on the display turnsto “---” when the accelerator pedal isdepressed. This indication remains as long asthe pedal is in a depressed position.zThe ACC control at the original set speedresumes as soon as you release the accelera-tor pedal. Under certain conditions, however,the braking control and alarming functions ofthe ACC may not work for a short while afterreleasing the accelerator pedal.zSet speed adjustment is impossible while theaccelerator pedal is in a depressed position.
To d e c r e a s e t h e s e t s p e e d

By using the “SET -” switch:
BK0203201EN.book 50 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*
Starting and driving 7-51
7
If you depress the brake pedal while the ACCcontrol is working, the control is cancelled,allowing you to decelerate the vehicle. At the point where the vehicle slows down toyour desired speed, push down the “SET -”switch; the new speed is then set in the sys-tem.
Simply depress the accelerator pedal to tem-porarily accelerate the vehicle. Releasing thepedal automatically slows down the vehicleto the set speed and the ACC restarts its con-trol.
NOTE
zThere is some time lag between the setting toa new speed and actually decelerating to thatspeed.zIf there is a vehicle in front and your vehicleis following that vehicle at a speed lowerthan the set speed, the set speed alonedecreases with no actual deceleration takingplace.zWhen the switch is held pushed, a buzzersounds every time the set speed changes.CAUTIONzThe setting speed should be set up the suita-ble speed according to a situation.
By using the brake pedal:
NOTE
zThe ACC control is ca
ncelled if you depress
the brake pedal and the ACC control doesnot resume even when you release the pedal.
To t e m p o r a r i l y a c c e l e r a t e t h e v e h i -cle
CAUTIONzThe ACC braking control and proximityalarm functions will not work while theaccelerator pedal is depressed.zThe setting speed should be set up the suita-ble speed according to a situation.
BK0203201EN.book 51 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*7-52 Starting and driving
7
Yo u c a n c a n c e l t h e A C C c o n t r o l b y u s i n geither of the methods below. When the control is cancelled, the system isplaced in the ‘standby state’. You can makethe system restart the control by using the“SET -” or “RES +” switch if the conditionsfor activating the control are met.zPress the “CANCEL” switch.zDepress the brake pedal.
When the system shifts into the ‘standbystate’ as a result of cancellation of the ACCcontrol, the “SET” indicator goes out. At thesame time, the display of the following dis-tance setting and running-ahead vehicle sym-bol (only when the ACC is detecting avehicle) is placed in the standby state of dis-play.
The ACC control is automatically cancelledand the ACC is placed in the ‘standby’ statein any of the situations listed below; you arealerted to this condition by the sound of abuzzer and a message on the display. You canmake the system restart the control by usingthe “SET -”” or “RES +” switch if the condi-tions for resuming the control are reestab-lished.zWhen your vehicle stops as the vehicle infront stops.zWhen the ASC is turned off.zWhen ABS, ASC or TCL is in operation.
NOTE
zThe set speed indication on the display turnsto “---” when the accelerator pedal isdepressed. This indication remains as long asthe pedal is in a depressed position.zIn certain conditions, the braking control andalarming functions of the ACC may not workfor a short while after releasing the accelera-tor pedal.zSet speed adjustment is impossible while theaccelerator pedal is
in a depressed position.
To t e r m i n a t e A C C c o n t r o l

To c a n c e l o f A C C c o n t r o l
NOTE
zYo u c a n a l s o c a n c e l t h e A C C c o n t r o l b ypressing the “ACC ON/OFF” switch. If thisswitch is pressed, the ACC is turned off.
BK0203201EN.book 52 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Forward Collision Mitigation System (FCM)*
Starting and driving 7-55
7
m Cruise control (automatic speed controlsystem) P.7-35
E00635101041
The FCM uses a sensor (A) to determine thedistance to a vehicle in front in the same laneand its speed relative to your vehicle’s speed.If the system judges that your vehicle is indanger of colliding against the vehicle almoststraight from behind, it gives you visual andaudible alarms (Forward collision warningfunction), increases the brake fluid pressure(FCM brake prefill function), and also pro-vides braking force assistance when you
depress the brake pedal (FCM brake assistfunction) to avoid frontal collision.When the risk of collision increases more, thesystem causes the brakes to work moderatelyto encourage you to apply brakes. If the sys-tem judges that a potential collision is immi-nent, it initiates emergency braking tomitigate collision-caused damages or to avoidpossible collision (FCM braking function).Stop lamps are illuminated during automaticbraking.
E00635401031
If the system judges that there is a risk ofyour vehicle colliding with a vehicle in front,
CAUTIONzCruise control (automa
tic vehicle speed con-
trol system) does not alert by proximityalarm and control dist
ance between vehicles
to the vehicle in front.
Forward Collision Mitiga-tion System (FCM)
*
WA R N I N GzA driver is responsible for driving safely.The FCM is the system to mitigate colli-sion-caused da
mages or to avoid collisions
as much as possible.The system is not intended to compensatefor driver’s loss of attention to the frontduring driving due to distraction or care-lessness or supplement a drop in visibilitydue to the rain and fog.It is never a substitute for your safe andcareful driving. Always be ready to applythe brakes manually.zThe FCM works to avoi
d frontal collisions
as much as possible.
However, the effect of
its operation varies
depending on situa-
tions and conditions, such as driving con-ditions, road conditions, and steering,acceleration and braking operations, sothat the performanc
e the function can
deliver is not always the same.If your vehicle is in danger of collision,take all necessary
collision-evading
actions, such as de
pressing the brake
pedal strongly regardless of whether thesystem is activated or not.
Forward collision warning function

BK0203201EN.book 55 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Forward Collision Mitigation System (FCM)*7-56 Starting and driving
7
this function warns you of the potential haz-ard with visual and audible alarms.When this function is triggered, a buzzersounds and, at the same time, a “BRAKE!”message appears on the information screen ofthe multi-information display.
E00635200016
If the system judges that there is a risk ofyour vehicle colliding with a vehicle in front,
this function prefills the brake line with addi-tional brake fluid to make the brakes moreresponsive to your brake pedal operation.
E00635301027
If the system judges that there is a risk ofyour vehicle colliding with a vehicle in front,this function deploys the brake assist soonerthe brake assist operation.
E00635501104
If the system judges that there is a high risk ofyour vehicle colliding with a vehicle in front,the system applies the brakes moderately toencourage you to apply the brakes. If the system judges that a collision is una-voidable, it initiates emergency braking con-
trol to mitigate collision-caused damages or,if the situation permits, to avoid a collision.When the emergency braking control is trig-gered, you are warned of the hazard with vis-ual and audible alarms like with the FCMalarm function.Once the emergency braking has worked, youare alerted to this by a message on the infor-mation screen of the multi-information dis-play.
CAUTIONzThis function does not work for a vehicle infront which is moving extremely slower thanyour vehicle.zUnder certain conditions, the audible alarmmay not work at all or may be scarcely audi-ble. Do not overly rely on the system; if yourvehicle is in danger of collision, take all nec-essary collision-evading actions, such asdepressing the brake pedal strongly regard-less of whether the system is activated or not.
FCM brake prefill function

FCM brake assist function

CAUTIONzThe brake assist function may not be trig-gered when the brake pedal is operated incertain ways.Do not overly rely on the system; if yourvehicle is in danger of collision, take all nec-essary collision-evading actions, such asdepressing the brake pedal strongly regard-less of whether the system is activated or not.
FCM braking function

CAUTIONzDo not use the FCM as a normal braking.zAfter your vehicle has stopped following theactivation of the FCM, automatic braking isreleased. As the vehicle will then start creep-ing, be sure to depress the brake pedal tohold the vehicle stationary.zWhen applying the brake during the auto-matic braking condition the pedal will feelfirm.This is not abnormal.Yo u c a n a p p l y m o r e p r e s s u r e t o t h e p e d a l t oassist in braking.
BK0203201EN.book 56 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分