alarm MITSUBISHI OUTLANDER SPORT 2014 3.G Owner's Manual

Forward Collision Mitigation System (FCM)*
Starting and driving 7-57
7
zIn the following situations, the system pro-vides neither cont
rol nor alarming.
•The vehicle in front of your vehicle is mov-ing at a speed much lower than your vehi-cle’s speed.•When a vehicle suddenl
y cuts in front of
your vehicle.•When the distance from a vehicle in front isextremely short.•To an oncoming vehicle.•When your vehicle’s speed is much lower.•When the selector leve
r is other in the “D”
(DRIVE) position.•When the system is faulty (if the systemself-detects any fault, the “FCM SERVICEREQUIRED” message is indicated and the“FCM OFF” indicator lights up on theinformation screen of the multi-informationdisplay).If the message remains after the operationmode has been turned to the “OFF” positionand then turned back to the “ON” position,contact a MITSUBISHI MOTORS Author-ised Service Point.CAUTION
zBraking function will not work in the follow-ing situations.•Your vehicle is driving at approximately 30km/h or faster while the vehicle in front isstationary or moving extremely slowly.•The ASC is OFF.zThe forward collision warning functionand/or the FCM braking function may notactivate in the following situations.•When a motorcycle, bicycle, pedestrian,animal, fallen objects, or anything otherthan a vehicle is present in front of yourvehicle.•When a vehicle suddenly appear just infront of your vehicle.•When a vehicle cuts in front of your vehiclevery closely.•When the vehicle in front is offset to theleft or right.•When the vehicle in front is towing atrailer.•A freight trailer that is not carrying a con-tainer.•The vehicle has a pr
otruding load from the
carrier.•The vehicle has a low vehicle height.•The vehicle has an extremely high groundclearance.•When there is a different object near thevehicle.CAUTION
•When driving on a road with many and suc-cessive curves, including when passingtheir entrances and outlets.•When accelerating and deceleratingquickly.•When the system recognizes driver’s steer-ing, accelerating, braking or gear shiftingactions as evasive actions to avoid colli-sion.•When driving on a road with steep andalternating up
and down slopes.
•When a road surface is surging, and there isunevenness.•When being driven in a tunnel.•When the your vehicle
changed lanes, and
your vehicle approached immediatelybehind the vehicle in front.•During a certain time after your vehicleturns left or right.•When you are carrying extremely heavyloads in the rear seats or luggage area.•After the Plug-in Hybrid EV System hasbeen running for an extended period oftime.•Under adverse weather conditions (rain,snow, sand storms, etc.)
*
•When the cover part in
front of the sensor
and the sensor become dirty or adheringsnow and ice
*.
•When water, snow or sand on the road areextorted by the vehicle in front or anoncoming vehicle
*.
CAUTION
BK0203201EN.book 57 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Forward Collision Mitigation System (FCM)*7-58 Starting and driving
7
*: When judging the state that detection per-formance deterioration and the FCM can’toperate temporarily by these situations auto-matically, “FCM TEMPORARILY NOTAVA I L A B L E ” m e s s a g e i s i n d i c a t e d , a n d a“FCM OFF” indicator lights up.Additionally, it may be indicated in the fol-lowing situations.•When the brake is over heating.•When you are driving in light traffic withfew vehicles and obs
tacles in front.
When the FCM will be in the state which canoperate, indication is released automatically.When indication keeps going out, there is anabnormal possibility of the system. Pleasecontact a MITSUBISHI MOTORS Author-ised Service Point.zFactors such as the positional relationshipbetween your vehicle and a vehicle in front,driver’s own technique of steering the vehi-cle and irregularly moving traffic due toaccidents or vehicle trouble may deter theFCM control and alarm from functioning.CAUTION
zWhen the system recognizes driver’s steer-ing or accelerating actions as evasive actionsto avoid collision, the FCM control andalarm functions may be canceled.zThe FCM control and alarm functions maybe triggered in the following situations.•When there is a structure (B) beside theentrance of a curve and intersection.•When running on a na
rrow iron bridge.
•When passing through a gate with smallhead or side clearances.•When there are metallic objects, steps orprojections on the road surface.•When quickly approaching a vehicle infront to overtake it.•When passing an electronic toll collectiongate.•When running under an
overpass, an pedes-
trian overpass or a small tunnel.•When running in Multi-storey car park.•When running the road the gradientchanges suddenly.•When stopping very close to a wall or avehicle in front.CAUTION
B
•When passing close to the vehicle or anobject.•When driving on the road that the vehicle infront runs in offset
position from your vehi-
cle.
zTurn off the system beforehand when thevehicle is placed in a
ny of the following situ-
ations as the system can operate unexpect-edly.•When your vehicle’s wheels are driven bythe Plug-in Hybrid EV System on a lift.•When your vehicle is towed or your vehicletows another vehicle.•When your vehicle is carried on a truck.•When enjoying sports driving on a circuit.•When your vehicle is on a chassisdynamometer or free rollers.•When the tyre pressure is not proper. CAUTION
BK0203201EN.book 58 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Forward Collision Mitigation System (FCM)*
Starting and driving 7-59
7
E00635601062
This switch is used to turn on and off theFCM and also to select your desired collisionalarm timing.When the switch is held pressed, the ON/OFFstate of the FCM changes from ON to OFFand vice versa. If you give the switch a shortpress with the FCM in the ON state, you canchange the collision alarm timing.
Yo u c a n s w i t c h t h e s y s t e m f r o m O F F t o O Nor ON to OFF if you hold the FCM ON/OFFswitch pressed when the operation mode isset to “ON”.Once the system is turned on, a buzzersounds, the information screen of the multi-information display shows the collision alarmtiming currently selected, and the “FCMOFF” indicator on the screen goes out.When you turn off the system, a buzzer soundand, at the same time, the “FCM OFF” mes-sage appears on the screen and the “FCMOFF” indicator comes on.Cycling the operation mode to ON will setthe FCM back ON.
•When installing the spare tyre for emer-gency.•When tyre chains are attached.zImproperly handling the system componentsmay result in such problems as degraded sen-sor performance and ultimately in an acci-dent. Be sure to take the followingprecautions to keep the system in good oper-ating conditions.•Avoid application of
strong shock loads to
the sensor and never tamper with or removethe sensor mounting screws.• The cover in front of the sensor and the sen-sor should be kept clean.•Do not cover the sensor mounted area ofthe vehicle or the sensor cover with asticker or anything such as a grill guardetc..•The sensor front cove
r should not be modi-
fied or painted.•Avoid using different
size tyres from those
specified and maintain even tyre wear.•Do not modify the suspension of your vehi-cle.
zIf the sensor mounted area of the vehicle isdeformed due to an acci
dent or some other
causes, turn off the system and please con-tact a MITSUBISHI MOTORS AuthorisedService Point.CAUTION
NOTE
zA sound will be heard during the activationof automatic braking, this is a function of thebrake control and is not abnormal.
FCM ON/OFF switch

To t u r n o n / o f f t h e s y s t e m

BK0203201EN.book 59 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Lane Departure Warning (LDW)*7-60 Starting and driving
7
Give a short press to the FCM ON/OFFswitch to change the timing at which the fron-tal collision alarm is triggered. Every timeyou press the switch, the alarm timingchanges alternately between “FAR” (earlieralarming) and “NEAR” (later alarming).As you make selection, the selected alarmtiming is displayed on the information screenof the multi-information display. Even afterturning off the FCM or setting the operationmode to “OFF”, the sy
stem retains your last
selected alarm timing in memory.When “NEAR” is selectedWhen “FAR” is selected
E00635701021
By recognizing through a camera (A) the lanein which your vehicle is running, LDW givesyou warning when your vehicle is likely todrift from its lane with an audible alarm and avisual alarm displayed on the informationscreen of the multi-information display.
E00635801022
The indication on the information screen ofthe multi-information display changes as fol-lows depending on the state of the system.When you set the operation mode to “ON”,the “LDW” indicator appears on the informa-tion screen of the multi-information display,showing that the system is placed in the ‘ONstate’.
To c h a n g e a l a r m t i m i n g

CAUTIONzFor the FCM brake prefill, the FCM brakeassist and the FCM braking functions, thefunction triggering timing cannot bechanged.
Lane Departure Warning (LDW)
*
How to operate LDW

Tu r n i n g o n t h e s y s t e m

BK0203201EN.book 60 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Lane Departure Warning (LDW)*7-62 Starting and driving
7
E00635901023
If a problem occurs with the system, a visualwarning specific to the type of the problem isgiven together with an audible alarm.The alarm shown below is displayed if thesystem becomes temporarily unable due totoo high a temperature of the LDW camera.If the camera cools down below the predeter-mined temperature, the system automaticallyrecovers the normal state.
The alarm shown below is displayed if LDWbecomes to a non-initialized state due to afault.If this happens, please contact a MITSUBI-SHI MOTORS Authorised Service Point forinspection of the system.
NOTE
zIf warning continues
for about 10 seconds or
more, the system switches to the standbymode before the warning stops.
System problem warning

To o h o t L D W c a m e r a

NOTE
zThe warning message can be cleared tempo-rarily by setting the LDW switch to “OFF.”
LDW deactivation due to fault

CAUTIONzLDW has its performance limitations. Do notover-rely on the system.zLDW is not designed to
lessen risks associ-
ated with not looking ah
ead carefully (atten-
tion drawn to something on the side,absentmindedness, etc.) or poor visibilitycaused by bad weather etc. Keep steeringyour vehicle correctly and drive safely.
zThe system may not be able to detect the lanecorrectly in the following conditions. Ifrequired, set the LDW switch to “OFF.”•When driving on a road whose lane mark-ings (white or yellow) are worn out orsmeared with dirt to an extent not recogniz-able by the system.•When lane markings are vague, typicallyduring a drive in the rain, snow or fog, orwhen running against the sun.•When the vehicle is moving in a placewhere lane markings are interrupted, suchas a toll booth entrance and motorway junc-tion.•When running on a road portion withincompletely removed old lane markings,shadows, lingering snow, truck-like puddlesmistakable for lane markings (especiallyafter the rain when road surface is reflect-ing light) or simila
r confusing factors.
•When running in a lane other than the cruis-ing lane and
passing lane.
•When running beside a closed lane sectionor in a provisional lane in a traffic workzone.•When running in an extremely narrow lane.•When the following distance between yourvehicle and a vehicle in front becomesextremely reduced (especially when amarking is hidden by a vehicle in front thisis running too close to the marking).•When entering a juncti
on or other point of
road where lanes are laid out complicatedly.CAUTION
BK0203201EN.book 62 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Bonnet11-4 Maintenance
11
2. Raise the bonnet while pressing the safetylock.3. Support the bonnet by inserting the sup-port bar in its slot.
1. Unlatch the support bar and clip it in itsholder.2. Slowly lower the bonnet to a positionabout 20 cm above the closed position,then let it drop.3. Make sure the bonnet is securely lockedby softly lifting the centre of the bonnet.
NOTE
zOnly open the bonnet when the wipers are inthe parked position. In any other position,the wipers could damage the paint or bonnet.
CAUTIONzNote that the support bar may disengage thebonnet if the open bonnet is lifted by a strongwind.zAfter inserting the support bar into the slot,make sure the bar supports the bonnetsecurely from falling down on to your heador body.
To c l o s e
CAUTIONzBe careful that hands or fingers are nottrapped when closing the bonnet.zBefore driving, make sure that the bonnet issecurely locked. An
incompletely locked
bonnet can suddenly open while driving.This can be extremely dangerous.NOTE
zIf this does not close
the bonnet, release it
from a slightly higher position.zDo not press down firmly on the bonnet asdoing so could damage it.zFor vehicles equipped with the securityalarm system, if you drive with the bonnetleft open, warn
ing display is displayed on the
information screen in the multi informationdisplay.
BK0203201EN.book 4 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Alphabetical index13-4
13
Coolant
..........................................
11-6
Plug-in Hybrid EV System warning lamp
......
6-39Position lamps
Bulb capacity
...............................
11-22
Replacement
................................
11-24
Power switch
......................................
7-10
Precautions to observe when using wipers and washers
............................................
6-53
Pregnant women restraint
....................
5-14
Puncture
Tyre repair kit
..................................
9-7
R
Ready indicator
..................................
6-37
Rear combination lamps
Bulb capacity
...............................
11-22
Replacement
................................
11-27
Rear differential oil
...........................
12-10
Rear fog lamp
Indicator lamp
................................
6-37
Switch
...........................................
6-47
Rear room lamp
..................................
8-67
Bulb capacity
...............................
11-23
Rear turn-signal lamps
Bulb capacity
...............................
11-22
Replacement
................................
11-27
Rear window demister switch
..............
6-53
Rear-view camera
...............................
7-67
Rear-view mirror
Inside
..............................................
7-6
Outside
...........................................
7-7
Refill capacities
................................
12-10
Regenerative braking level selector (paddle)
.
7-17Replacement of lamp bulbs
................
11-21
Reversing lamps
Bulb capacity
................................
11-22
Replacement
.................................
11-26
Reversing sensor system
......................
7-63
Roof carrier precaution
........................
7-70
Room lamp
.........................................
8-67
S
Safe driving techniques
.........................
7-4
Safety and disposal information for used engine oil
.........................................
2-15
S-AWC (Super All Wheel Control)
.......
7-18
Seat
Adjustment
......................................
5-2
Front seats
.......................................
5-3
Head restraints
.................................
5-5
Heated seats
.....................................
5-4
Making a flat seat
.............................
5-8
Making a luggage area
......................
5-7
Seat belt
Adjustable seat belt anchor
..............
5-12
Force limiter
..................................
5-15
Inspection
......................................
5-21
Pregnant women restraint
................
5-14
Pre-tensioner
..................................
5-14
Seat belt reminder
...............................
5-11
Seat belts
.............................................
5-9
Child restraint
................................
5-15
Seats
Rear seats
........................................
5-5
Security alarm system
.........................
4-24
Select Position indicator
......................
7-15
Selector Lever (Joystick Type)
.............
7-14
Service precaution
..............................
11-2
Side turn-signal lamps
Bulb capacity
...............................
11-22
Snow tyres
.......................................
11-11
Spark plug
..........................................
12-8
Specifications
.....................................
12-2
Speed Limiter
.....................................
7-39
Spray can
...........................................
2-16
Starting and stopping the Plug-in Hybrid EV System
.............................................
7-12
Steering
Steering wheel height adjustment
.......
7-6
Stop lamps
Bulb capacity
...............................
11-22
Replacement
................................
11-27
BK0203201EN.book 4 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分