light MITSUBISHI SPYDER 1990 Service Manual PDF

ENGINE AND EMISSION CONTROL Auto-cruise Control System
INSPECTION PROCEDURE 3
When brake pedal is depressed,, auto-cruise control does not
cancel.
[Comment]A malfunction of the stop light switch or stop ligh t circuit may exist.
Probable cause
l Malfunction of the stop light switch.
l Malfunction of the connector.
l Malfunction of the
l Malfunction of the PCM.
Stop light switch check.
(Refer to
OK
Measure at stop
switch connector
lDisconnect the connector and mea-sure at the harness side.
l Voltage between terminal (1) and
ground positive voltage
following connectors:
NG
63 and
NG
Check troubleNGsymp Check the l i g h t a n d P C M . R e p a i r ,
OK Check trouble symptom.
Replace the PCM.
light switch and the
ground.
,
INSPECTION PROCEDURE 4
When selector lever is set to range, auto-cruise control does
not cancel.
[Comment]An open-circuit in the output signal circuit in IN range may be present.
OK
and.
TSB Revision
Inspect thebetween the NG
transaxle range switch and PCM.
OK
the PCM.
INSPECTION PROCEDURE 5
When auto-cruise control CANCEL switch is set to ON ,
auto-cruise control does not cancel. Probable cause
[Comment]An open-circuit inside the CANCEL switch may be pre
sent.l
Malfunction of the auto-cruise control switch.
Replace the auto-cruise control

17-16ENGINE AND EMISSION CONTROL Auto-cruise Control System
INSPECTION PROCEDURE 9
Auto-cruise control main switch illumination light does not
illuminate. Probable cause
A malfunction of the auto-cruise control main switc
h, or connector may exist.l
Malfunction of the auto-cruise control mainswitch.l Malfunction of the connector.
l Malfunction of the harness.
Auto-cruise control main switch check(Refer to Replace
OK
Measure at auto-cruise control main
switch connector
lDisconnect the connector and mea-sure at the harness side.
l Voltage between terminal (2) and
groundOK: Battery positive voltage
II
OK
Check trouble symptom.
N Gpower supply. Repair, if necessary.
Check the harness between the
auto-cruise control main switch and
rheostat. Repair, if necessary.
INSPECTION PROCEDURE 10
Auto-cruise control indicator inside combination me ter does
not illuminate. (However, auto-cruise control is no rmal.)Probable cause
TSB Revision
l
Malfunction of the bulb.
l Malfunction of the
l Malfunction of the connector.
l Malfunction of the PCM.
(Refer to
illuminate when terminal (22) of PCM connector A-l 06 is

ENGINE AND EMISSION CONTROL Auto-cruise Control
When using a voltmeter
1.Use the special tool to connect a voltmeter between the
ground terminal and the diagnostic output terminal of
d a t a l i n k c o n n e c t o r .
2.In the same way as when using the scan tool, turn t he
ignition switch to ON and turn on the auto-cruise c ontrol
main switch. Then take a reading of the diagnostic trouble.
codes from the movement of the needle on the voltme ter.
HOW TO READ DIAGNOSTIC TROUBLE CODES FROM A VOLTMET ER
Example of diagnostic trouble code voltage waveformNormalvoltage waveform
For diagnostic trouble code No. 24
NOTE
Other on-board diagnostic items are also output as voltage waveforms corresponding to diagnostic troub le code
numbers.
HOW TO ERASE DIAGNOSTIC TROUBLE CODES
The diagnostic trouble codes can
erased by disconnecting the cable from the battery for 10 seconds
or more and then reconnecting it, or by the followi ng procedure.
1. Turn the ignition switch to ON.
2.With the SET switch at the ON position, turn the ma in switch to ON, and within 1 second after this,
turn the RESUME switch to ON.
3. With the SET switch once more at the ON position , turn the stop light switch ON for a continuous
period of 5 seconds or more.
Auto-cruise control switch
TSB Revision
HOW TO READ INPUT SWITCH CODES
1. Connect the scan tool or a voltmeter to the data link
connector. (Refer to
2.With the ignition switch in the ON position, turn t he S E T
switch to the ON position.
3.Within 1 second after turning the auto-cruise contr ol main
switch to ON, turn the RESUME switch to ON.
4. Operate each switch listed in the input inspecti on table
and take a reading of the input switch codes with t he
scan tool or the fluctuation of a voltmeter.
NOTE
These codes are output as voltage waveforms in the
same way as above.

AND CONTROL
Input Inspection Table
.
Code No.Input operation Operation
21SET switch ONAuto-cruise control-ECU judges that SET switch is O
N
22RESUME switch ON Auto-cruisecontrol-ECU judges that ON
23 Stop light switch
(ON when brake pedal depressed) Auto-cruise control-ECU judges that stop light swit
ch is ON
24
25
26Auto-cruise control-ECU judges that vehicle speed i s 40
km/h (25 mph) or higher ,Vehicle speed signal
Auto-cruise control-ECU judges that speed is lower
than 40 km/h (25 mph)
lClutch pedal position switch Auto-cruise control-ECU judges that clutch (ON when clutch pedal depressed) Park/neutral position switch switch or park/neutral position ONl(ON when selector lever in range)
27 CANCEL switch ON Auto-cruise control-ECU judges that
ON
28 Throttle position sensor signal Auto-cruise control-ECU judges that throttle
voltage is 1.5 or more
29Closed throttle position switch,Auto-cruise control-ECU judges
switch is OFF
INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODES,
Code No.
On-board diagnostic items page
11Auto-cruise vacuum pump drive system
12
14
15
Vehicle speed signal system
Auto-cruise vacuum pump power supply system
Auto-cruise control switch
17-21
.
16
17
Auto-cruise control-ECU
Throttle position sensor system
TSB Revision

E N G I N E A N D E M I S S I O N C O N T R O L Auto-cruise
INSPECTION PROCEDURE: FOR DIAGNOSTIC TROUBLE CODES
Code Auto-cruise vacuum pump drive system
[Comment]
This diagnostic trouble code is output if the release valve, control valve and motor drive signals
from the auto-cruise vacuum pump are not input to t he auto-cruise control-ECU.
(Refer to
l Malfunction of the auto-cruise vacuum pump
l Malfunction of the auto-cruise control-ECU
Measure at
control-ECU
connector
lDisconnect the connector and mea-sure at the harness side.
lVoltage between terminal (12) andground (for driving release valve)lVoltage between terminal (13) andground (for driving control valve)
lVoltage between terminal (26) andground (for driving motor)
OK: Battery positive voltage
Measure at auto-cruise vacuum pump
connector Stop light switch check
I
(Refer to l sure at the harness side.
l Voltage between terminal andgroundOK: Battery positive voltage
OK
auto-cruise control main switch and
auto-cruise vacuum pump. Repair, if
N G
and
OK
Check trouble symptom.
following
OK
Check trouble symptom.
NG
Replace the control-ECU.
TSB Revision
C h e c k t h e b e t w e e n t h eauto-cruisev a c u u m p u m p a n d
auto-cruise control-ECU. Repair, if
necessary.

ENGINE AND EMISSION CONTROL Auto-cruise Control’
Code 2 Vehicle speed signal system
[Comment]l Malfunction of the vehicle This diagnostic trouble code is output if the vehic le speed signals from the vehicle speed sensor l of connectorare not input to the auto-cruise control-ECU when t he vehicle speed is 40 km/h (25 mph) l
Malfunction of the harness
or more. l Malfunction of the auto-cruise
Check the vehicle speed sen(Refer to GROUP 54 CombinationMeter.)
1. NG
Measure at the vehicle speed sensor connector Check the following connector. l Disconnect the connector, and measure at the
harness side.O K
1. Voltage between 1 and ground (Ignition switch: ON)
NG
System voltage
2.Voltage between 3 and ground2. N G(Ignition switch: ON)
OK: 4.6 5.2 3.Continuity between 2 and ground3. N G
OK: Continuity
OK
Check trouble symptom.
N G
Check the harness between the speed sensor
Check the following
OKNG
Check trouble symptom.
NG
Check the harness between the auto-cruise ECU and the vehicle soeed sensor connector.
OKNG
Replace the auto-cruise control-ECU.
and ignition switch connector
OK
Check the ignition switch.
(Refer to GROUP 54 , ,
Check the harness between the vehicle speed sensorand the ground. Repair, if necessary.
Code Autocruise vacuum pump power supply systemProbable cause
[Comment]
This code will be output when the drive signals for the auto-cruise vacuum pump release valve,
control valve and motor are not input to the auto-c ruise control-ECU.l
the stop light l
Malfunction of the connector
l
l of the auto-cruise
at the auto-cruise vacuum
l Disconnect the connector and
l Voltage between terminal (1) and
OKN G Check the harness between the cruise vacuum pump and the cruise control-ECU.
and
Replace the auto-cruise control-ECU.
TSB Revision

ENGINE AND EMISSION CONTROL Auto-cruise Control
INSPECTION CHART FOR SYMPTOMS
Communication with
scan tool is not
possible. Communication with systems is not possible.
Communication with auto-cruise control-ECU only
is not possible.1
2
Input switch inspection using the scan tool is not possible. (However,
diagnostic inspection is possible.)3 .
Auto-cruise control When brake pedal is depressed 4 does not cancel. When clutch pedal is depressed
When select lever is set to range
When CANCEL switch is set to ON
5
17-26
I 7 17-27
Trouble symptomInspection
procedure No.Reference page
The diagnosis result displayed on the scan tool is normal even though
auto-cruise control cannot be set.
Auto-cruise control cannot be set.I9
Hunting (repeated acceleration and deceleration) oc curs at the set vehicle
speed.I1
When the auto-cruise control main switch is ON, the switch indicator on the
instrument panel does not illuminate. (However, aut o-cruise control is normal.)
Auto-cruise control main switch illumination light does not illuminate.111 7 - 2 9 , .
1217-29
Auto-cruise control indicator light inside combinat ion meter does not illuminate.
(However, auto-cruise control is normal.)13
TSB Revision

ENGINE AND EMISSION System
.,
INSPECTION PROCEDURE 3
Input switch inspection using the scan tool is pdssible.
(However, diagnostic inspection is possible.)
I
[Comment]A malfunction of auto-cruise control switch circuit system may be present.l
Malfunction of the auto-cruise control l Malfunction of the clock spring .
l of the connector.
l Malfunction of the harness.
.
NG
(Refer to
Measure at clock spring connector
l sure at the harness side
l Voltage between terminal (2) and
groundOK: Battery positive voltage
OK
Check trouble symptom.
C h e c k t r o u b l e spring and auto-cruise
INSPECTION PROCEDURE 4
When brake pedal is depressed, auto-cruise control does not
cancel.Probable , ,
[Comment]A malfunction of stop light switch or a malfunction of stop light circuit may be present.l
Malfunction of the stop light switch.
l Malfunction of the connector.
l Malfunction of. the
l Malfunction of the auto-cruise control-ECU.
Does stop
illuminate?
No
Replace the auto-cruise control-ECU.
lDisconnect the connector and mea-sure at the harness side.
Check trouble symptom.Check the following connectors:
TSB Revision

ENGINE AND EMISSION CONTROL Auto-cruise
INSPECTION PROCEDURE 11
When the auto-cruise control main switch is ON, the switch
indicator on the instrument panel does not illumina te.
(However, auto-cruise control is normal.) Probable cause
[Comment]l auto-cruise control main
Blown bulb in auto-cruise control main switch.switch.
Replace the auto-cruise control main switch.
INSPECTION PROCEDURE 12
Auto-cruise control main switch illumination light does not
illuminate. Probable cause
[Comment]A malfunction of auto-cruise control main switch, h
arness, or connector may exist.l
Malfunction of the auto-cruise control main
switch. Malfunction of the connector.
l Malfunction of the harness.
(Refer to
Measure at auto-cruise control main
switch connector
lDisconnect the connector and mea-sure at the harness side.
l Voltage between terminal (2) and
groundOK: Battery positive voltage
NG
Check trouble symptom.
TSB Revision

ENGINE AND EMISSION CONTROL Auto-cruise Control
INSPECTION PROCEDURE 13
Auto-cruise control indicator inside combination meter does
not illuminate. (However, auto-cruise control is no rmal.)Probable cause
[Comment]A malfunction of the bulb, the connector harness may be present. l
Malfunction of the bulb.
l Malfunction of the harness. Malfunction of the connector.
l Malfunction of the auto-cruise control-ECU.
to
illuminate when terminal (23) of
Check trouble symptom.
Replace the auto-cruise control-ECU. Check the harness between the
combination meter and auto-cruise
control-ECU.
if
INSPECTION PROCEDURE 14
Stop light switch input circuit system check (Code No. 23)II
Stoplight switch check (Refer to
Check the harness between jumper connector and
auto-cruise control-ECU. Repair, if necessary.
INSPECTION PROCEDURE 15 C l u t c h p e d a l p o s i t i o n s w i t c h
or p o s i t i o n s w i t c h i n p u t c i r c u i t s y s t e m c h e c k
( C o d e N o . 2 6 )

Check trouble symptom.
OK
NG
Check the harness between clutch pedal position swi tch and
auto-cruise control-ECU. Repair, if necessary.
Park/neutral position switch check (Refer to
Starter relay continuity check
(Refer to GROUP 16 Starting System.)
57
Check trouble symptom. Check the harness between auto-cruise control-ECU and power
TSB Revision