brake light NISSAN CUBE 2010 3.G Quick Reference Guide

REMOTE KEYLESS ENTRY SYSTEM (if so equipped)
LOCK DOORS
Press the
button to lock all doors.

UNLOCK DOORS
Press the
button once to unlock the driver’s door only.
Press the button again within 5 seconds to unlock all doors.
USING THE PANIC ALARM
Press and hold the
button for longer than 1 second.
The panic alarm will sound and the headlights will stay on
for 25 seconds. The panic alarm stops when it has run for
25 seconds or when any button is pressed on the keyfob.
2
NISSAN INTELLIGENT KEY™ (if so equipped)
The niSSA n intelligent key™ allows you to lock or unlock your vehicle, open
your back door and start the engine.
n OT e: it is important to make sure the intelligent key is with you (that is, in
your pocket or purse).

The operating range of the door and back door/unlock function is
approximately 31 in (80 cm).

Locking the vehicle - Push any door handle Request Switch
01 once.

unlocking the vehicle - Push any door handle
Request Switch

01 once. The corresponding door
will unlock. Push the door handle Request Switch


01 again within 5 seconds; all other doors will unlock.
STARTin
G THe enGine
depress the brake pedal.

Push the ignition switch START/STOP button to start
the engine.
TuRnin G THe en Gine Off
Move the shift lever to the P (PAR k) position and apply
the parking brake.

Push the ignition switch START/STOP button to turn
the engine off.
01

AcceSSORY POSi TiOn
Press the ignition switch START/STOP button once without depressing the brake pedal to
access the A cc position. This position activates electrical accessories such as the radio.

Press the ignition switch START/STOP button a second time without depressing the brake
pedal to access the O n position. This position turns on the ignition switch and all electrical
accessories.
niSSAn inTe LLiGenT keY™ BATTe RY diSc HARG e
if the battery of the intelligent k ey is completely discharged, the
i ntelligent key system warning light in the instrument panel blinks in
yellow after pushing the ignition switch START/STOP button. To start
the engine with a discharged intelligent key, perform the following
procedure:

Move the shift lever to the P (PAR k) position.

firmly apply the foot brake.

Touch the ignition switch START/STOP button with the intelligent
k ey. A chime will sound.

Push the ignition switch START/STOP button while depressing
the brake pedal within 10 seconds after the chime sounds. The
engine will start.
if the intelligent k ey system warning light in the instrument panel is blinking in green, re\
place the
battery as soon as possible. This warning means that the intelligent k ey battery is almost discharged.
n OTe: if the ignition switch is pushed without depressing the brake pedal, the ignition switch will
change to the A cc position.
OPenin G THe BAck d OOR
To open the back door, unlock and pull the handle.
u nlock the back door using one of the following
operations:

Push the
button on the keyfob or the
intelligent
k ey twice.

Push the back door Request Switch
01 (if so
equipped).

Push the power door lock switch to the unlock position.

insert the key into the driver’s door key cylinder and turn towards th\
e rear of the vehicle twice.
01

6
CRUISE CONTROL (if so equipped)
To activate cruise control, push the CRUISE ON/OFF switch.
The c Rui Se indicator light in the instrument panel will illuminate.

To set cruising speed, accelerate the vehicle to the desired speed,
push the COAST/SET switch and release.

To reset at a faster cruising speed, push and hold the ACCEL/
RES switch. When the vehicle attains the desired speed, release
the switch.

To reset at a slower cruising speed, push and hold the COAST/
SET switch. Release the switch when the vehicle slows to the
desired speed.

To cancel cruise control, push the CANCEL switch or tap the brake pedal.

To resume a preset speed, push and release the ACCEL/RES switch. The vehicle returns to
the last set cruising speed when the vehicle speed is over 24 MPH (38 km/h).

To turn off cruise control, push the CRUISE ON/OFF switch. The c Rui Se indicator light in
the instrument panel will go out.
AUTOMATIC CLIMATE CONTROL (if so equipped)
01 AUTO BUTTON

Press the AUTO button
01 . use the temperature control buttons
02 to set the desired
temperature. This will allow the fan speed, air flow distribution and temperature to be
automatically maintained at the selected temperature.

To disable auto mode, press the MODE button
03 , one of the fan speed control buttons

04 or the front defroster control button 05 .
02 TEMPERATURE CONTROL BUTTONS

Press the temperature control buttons
02 , up to increase the temperature or down
to decrease the temperature.

The temperature range is between 60°f and 90°f .
05
1004
030809
07
0201
06