tow NISSAN CUBE 2010 3.G Quick Reference Guide

AcceSSORY POSi TiOn
Press the ignition switch START/STOP button once without depressing the brake pedal to
access the A cc position. This position activates electrical accessories such as the radio.

Press the ignition switch START/STOP button a second time without depressing the brake
pedal to access the O n position. This position turns on the ignition switch and all electrical
accessories.
niSSAn inTe LLiGenT keY™ BATTe RY diSc HARG e
if the battery of the intelligent k ey is completely discharged, the
i ntelligent key system warning light in the instrument panel blinks in
yellow after pushing the ignition switch START/STOP button. To start
the engine with a discharged intelligent key, perform the following
procedure:

Move the shift lever to the P (PAR k) position.

firmly apply the foot brake.

Touch the ignition switch START/STOP button with the intelligent
k ey. A chime will sound.

Push the ignition switch START/STOP button while depressing
the brake pedal within 10 seconds after the chime sounds. The
engine will start.
if the intelligent k ey system warning light in the instrument panel is blinking in green, re\
place the
battery as soon as possible. This warning means that the intelligent k ey battery is almost discharged.
n OTe: if the ignition switch is pushed without depressing the brake pedal, the ignition switch will
change to the A cc position.
OPenin G THe BAck d OOR
To open the back door, unlock and pull the handle.
u nlock the back door using one of the following
operations:

Push the
button on the keyfob or the
intelligent
k ey twice.

Push the back door Request Switch
01 (if so
equipped).

Push the power door lock switch to the unlock position.

insert the key into the driver’s door key cylinder and turn towards th\
e rear of the vehicle twice.
01

4
AUTOMATIC DOOR LOCKS
All doors lock automatically when the vehicle speed reaches 15 MPH (24 km/h).

All doors unlock automatically when the ignition switch is placed in the O ff position
(intelligent key equipped vehicles) or when the key is removed from the ignition switch
(mechanical key equipped vehicles).
The automatic unlock function can be deactivated or activated. To deactivate or activate the
automatic door unlock system, perform the following procedure:
1. close all doors.
2. Place the ignition switch in the O n position.
3. Within 20 seconds of performing Step 2, push and hold the power door lock switch to the


position (un
LOck) for more than 5 seconds.
4. When activated, the hazard indicator will flash twice. When deactivated, the hazard
indicator will flash once.
5. The ignition switch must be placed in the O ff and On position again between each setting
change.
When the automatic door unlock system is deactivated, the doors do not unlock when the ignition
switch is placed in the O ff position ( intelligent key equipped vehicles) or when the key is removed
from the ignition switch (mechanical key equipped vehicles). To unlock the door manually, use the
inside lock knob or the power door lock switch (driver’s or front-passenger’s side).
WINDSHIELD WIPER/WASHER SWITCH
The ignition switch must be in the O n position to
activate the windshield wipers.

Move the lever to the following positions to operate
the windshield wipers:

1A intermittent (INT) –
front wipers operate
intermittently and can be further adjusted by
twisting the time control ring

1B .

02 Low Speed (LO) –
continuous low-speed
operation of front wipers.

03 High Speed (HI) –
continuous high-speed
operation of front wipers.

04 Mist (MIST) – Push the lever up for one sweep
of the front wipers.

05 Rear Wiper (REAR) – Twist the end section to operate the first (INT) or second (ON)

speed settings for the rear wiper.

The washer function activates the washer fluid and several sweeps of th\
e wipers:
• For FRONT WASHER, pull the lever toward you.
• For REAR WASHER, push the lever away from you.
1B
04
05
1A
02
03