brake light NISSAN FRONTIER 2008 D22 / 1.G Quick Reference Guide

STEERING WHEEL SWITCHES FOR AUDIO CONTROL/
BLUETOOTH (if so equipped)
Press the MODEbutton to turn the radio system on.
 To choose PresetA,B, C, CD, AUX orXM (if so equipped)
press MODE repeatedly.
 The tuning up or down
switch can be used to perform the
following:
● Push the
switch for less than 1.5 seconds to change to a
preset station.
● Push and hold the
switch for more than 1.5 seconds to seek the next or previous
broadcasting radio station.
● Push the
switch while playing a CD (if so equipped) for less than 1.5 seconds to
change tracks on the CD.
● If the vehicle is equipped with a CD changer, push and hold the
switch for more
than 1.5 seconds to change between CDs.
 Push the VOLcontrol switch up or down to increase or decrease the volume.
CRUISE CONTROL (if so equipped)
To activate thecruise control, pushtheON·OFF switch.The
indicator light in the instrument panel will illuminate.
 To set cruising speed,accelerate thevehicle tothe desired
speed, pushthe COAST/SET switchandrelease it.The SET
indicator light in the instrument panel will illuminate.
 To reset atafaster cruising speed,pushandhold the
ACCEL/RES switch.Whenthevehicle attainsthespeed you
desire, release the switch.
 To reset at a slower cruising speed, push and hold the COAST/SETswitch. Release the
switch when the vehicle slows to the desired speed.
 Tocancel cruisecontrol, pushtheCANCEL switchortap thebrake pedal. TheSET
indicator light in the instrument panel will go out.
 To resume apreset speed, pushandrelease theACCEL/RES switch.Thevehicle
returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h) .
 To turn off cruise control, push the ON·OFFswitch. Both the CRUISE indicator light and
the SET indicator light in the instrument panel will go out.
4

FOUR-WHEEL DRIVE (4WD) SHIFT SWITCH (if so equipped)
This system provides three positions so the driver can select
the desired drive mode according to driving conditions.
 2WD – Dry, paved roads.
 4H –Rocky, sandyorsnow-covered roads.(Before placing
4WD shiftswitch in4H position from2WD, ensure vehicle
speed is less than 62.5 MPH [100 km/h]) .
 4LO – When maximum power and traction are required (steep
grades, rocky, sandy or muddy roads) .
NOTE: The vehicle must be stopped and in N (Neutral) with the brake pedal depressed when
shifting into and out of 4LO.
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped)
The Vehicle Dynamic Control (VDC) system is designed to help improve
driving stability. VDC detects wheel spin and controls braking and engine
output. VDC may need to be temporarily shut off if you are trying to free a
vehicle stuck in snow or mud.
 Push the Vehicle Dynamic Control (VDC) off switch to deactivate the
VDC system. The
lightwillilluminate inthe instrument panel
gauge area.
 Push the Vehicle Dynamic Control (VDC) off switch again to activate the VDC system.
The
light in the instrument panel gauge area will turn off.
 The VDC system is active while the vehicle is running until the switch is pressed to turn
it off.
E-LOCK SWITCH (if so equipped)
The Electronic LockingRearDifferential (E-Lock)systemcan
help provide addedtraction ifthe vehicle isstuck orbecoming
stuck.
To activate the system:
 The 4WD switch must be in the 4LO position (4-wheel drive
vehicles) ,
 The vehicle must be stopped or moving at 4 mph or less, and
 The E-Lock system switch must be turned on.
Once the vehicle is free, the system should be turned off.
9

HILL DESCENT CONTROL SWITCH (if so equipped)
Thehilldescent controlsystem isdesigned toreduce driver
workload when going down steep hills. The hill descent control
system helps to control vehicle speed so the driver can concen-
trate on steering the vehicle.
To activate the hill descent control system:
 The automatic transmission selectorlevermust beinfor-
ward or reverse gear,
 The 4WD switch must be in the 4L position and the vehicle
speed must be under 15 MPH (25 km/h) , or
 The 4WD switch must be in the 4H position and the vehicle speed must be under 21
MPH (35 km/h) , and
 The hill descent control system switch must be on.
 The hill descent control indicator light will come on when the system is activated. Also,
the stop/tail lights illuminate while the hill descent control system applies the brakes to
control vehicle speed. To turn off the hill descent control system, push the switch to the
off position. The hill descent control system is temporarily disabled when the brake or
accelerator pedal is depressed.
HILL START ASSIST (if so equipped)
The hill start assist system automatically keeps the brakes applied to help prevent the vehicle
from rolling backwards in the time it takes the driver to release the brake pedal and apply the
accelerator when the vehicle is stopped on a hill.
Hill start assist will operate automatically under the following conditions:
 The selector lever is shifted to a forward or reverse gear.
 The vehicle is stopped completely on a hill by applying the brake.
The maximum holding time is 2 seconds.
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air Bag System.
Under some conditions, depending on the type of occupant or object
detected inthe front passenger seatbythe occupant classification
sensor, the front-passenger air bag is designed to automatically turn
OFF. When the front-passenger air bag is OFF,the front-passenger
air bag status light will illuminate*. For example:
 When thesystem detects thatthefront-passenger’s seatis
occupied by a small adult, child or child restraint as outlined in
the Owner’s Manual, the
will illuminate to indicate that the front-passenger air
bag is OFF and will not inflate in a crash.
10