ignition NISSAN GT-R 2009 Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2009, Model line: GT-R, Model: NISSAN GT-R 2009Pages: 311, PDF Size: 6.68 MB
Page 184 of 311
Black plate (179,1)
Model "R35-D" EDITED: 2008/ 5/ 20
IGNITION SWITCH POSITIONS
LOCK (Normal parking position)The ignition switch can only be locked in this
position.
The ignition switch will be unlocked when it is
pushed to the ACC position while carrying the
Intelligent Key or with the Intelligent Key inserted
in the port.ACC (Accessories)This position activates electrical accessories
such as the radio, when the engine is not
running.ON (Normal operating position)This position turns on the ignition system and
electrical accessories.OFFThe engine can be turned off without locking the
steering wheel.
The ignition lock is designed so that the ignition
switch cannot be switched to the LOCK position
until the shift lever is moved to the
&Pposition.
NOTE:.If the steering lock release malfunction
indicator appears on the vehicle infor-
mation display when the ignition
switch is pressed, press the ignition
switch again while gently turning the steering wheel left and right.
(
“STEERING LOCK RELEASE
MALFUNCTION INDICATOR” page 2-
41)
. If the shift
&Pwarning appears on the
vehicle information display when the
ignition switch is pushed, the shift lever
is in any position except the
&P
posi-
tion. Move the shift lever to the&P
position. (
“SHIFT “P” WARNING”
page 2-40)
. If the Intelligent Key battery discharge
indicator appears on the vehicle infor-
mation display, the Intelligent Key
battery is discharged and the ignition
switch will not operate. Insert the
Intelligent Key into the key port to
operate the ignition switch.
(
“INTELLIGENT KEY BATTERY
DISCHARGE INDICATOR” page 2-42)
. When all of the following conditions
are met for 60 minutes, the battery
saver system will cut off the power
supply to prevent battery discharge.
— The ignition switch is in the ACC
position, and
— All doors are closed, and
— The shift lever is in the
&Pposition. .
Do not leave the vehicle with the
ignition switch in the ACC or ON
position when the engine is not run-
ning for an extended period of time.
This can discharge the battery.
Starting and driving
5-9
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 185 of 311
Black plate (180,1)
Model "R35-D" EDITED: 2008/ 5/ 20
INTELLIGENT KEY BATTERY DIS-
CHARGEIf the battery of the Intelligent Key is almost
discharged, the guide light
*1
of the Intelligent
Key port blinks and the indicator appears on the
vehicle information display.
(
“INTELLIGENT KEY INSERTION INDI-
CATOR” page 2-41)
In this case, inserting the Intelligent Key into the
port allows you to start the engine. Make sure
that the mechanical key side faces backward as
illustrated. Insert the Intelligent Key in the port
until it is latched and secured.
To remove the Intelligent Key from the port, push
the ignition switch to the OFF position and pull the Intelligent Key out of the port.
NOTICE
Never place anything except the Intelli-
gent Key in the Intelligent Key port.
Doing so may cause damage to the
equipment.
NOTE:.
Make sure the Intelligent Key is in the
correct direction when inserting it into
the Intelligent Key port. The engine
may not start if it is in the incorrect
direction.
. Remove the Intelligent Key from the
Intelligent Key port after the ignition
switch is pushed to the OFF position.
5-10
Starting and driving
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 186 of 311
Black plate (181,1)
Model "R35-D" EDITED: 2008/ 5/ 20
.The Intelligent Key port does not
charge the Intelligent Key battery. If
you see the low battery indicator in the
vehicle information display, replace the
battery as soon as possible.
(
“INTELLIGENT KEY BATTERY RE-
PLACEMENT” page 8-23)
. Make sure the area around the vehicle is
clear.
. Check fluid levels such as engine oil, cool-
ant, brake fluid and window washer fluid as
frequently as possible, or at least whenever
you refuel.
. Check that all windows and lights are clean.
. Visually inspect tires for their appearance
and condition. Also check tires for proper
inflation.
. Lock all doors.
. Position seat and adjust head restraints.
. Adjust inside and outside mirrors.
. Fasten seat belts and ask all passengers to
do likewise.
. Check the operation of warning lights when
the ignition switch is pushed to the ON
position. (
“WARNING/INDICATOR
LIGHTS AND AUDIBLE REMINDERS”
page 2-23)
NOTE:. This vehicle includes spark plugs that
are designed for maximum perfor-
mance. If the start time becomes long-
er, the plugs may be fouled, making the
engine difficult to start. If this occurs,
start the engine using the procedure
described in this section.
. A click sound may be heard when the
brake pedal is depressed and released.
This is normal.
. A low rattling operating sound may
occur when the engine is started or
stopped. This does not indicate that
there is a malfunction. This sound is
likely to occur in particular if the engine
is stopped when the temperature of the
transmission oil is high.
Starting and driving
5-11
BEFORE STARTING THE ENGINE STARTING THE ENGINE
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 187 of 311
Black plate (182,1)
Model "R35-D" EDITED: 2008/ 5/ 20
1. Check the positions of the accelerator pedal
*1
and brake pedal
*2. Adjust the steering
wheel and seat positions so that the correct
driving posture is achieved. (
“FRONT
SEATS” page 1-2)
2. Check that the parking brake is engaged.
3. Check that the shift lever is in the&Por&N
position. (
&Pis recommended.)
4. Firmly depress the brake pedal. Without depressing the accelerator pedal, press the
ignition switch once to start the engine.
5. To stop the engine, move the shift lever to the
&Pposition, and push the ignition switch
to the OFF position.
NOTE:. If the engine is difficult to start, de-
press the accelerator pedal all the way
to the floor and hold it. Push the
ignition switch with the brake pedal
depressed to start cranking the engine.
After 5 or 6 seconds, stop cranking by
pushing the ignition switch to the OFF
position, and then release the accel-
erator pedal. Then perform steps 1 to 4
to start the engine. If the engine starts,
but fails to run, repeat this procedure.
. Starting and stopping the engine over a
short period of time may make the
vehicle more difficult to start. If this
occurs, wait for more than 3 minutes,
and then press the ignition switch
again to start the engine.
. To maintain high performance over a
long period of time, the engine speed is
limited to 5,000 rpm when the engine is
revved with the shift lever in the
&Nor
&Pposition, and to 4,000 rpm when the
engine oil or coolant temperature is
low or higher than normal.
. If the ignition switch is pressed before
the shift lever is moved to the
&P
position, the ignition switch will not
change to the OFF position. If this occurs, the SHIFT
&P
warning display
appears on the vehicle information
display. When stopping the engine, be
sure to move the shift lever to the
&P
position and then press the ignition
switch. Failure to do so may result in
discharge of the battery. (
“SHIFT
“P” WARNING” page 2-40)
. If the shift lever was in the
&A↔&Mor
&R
position when the engine was stopped,
then be sure to move the shift lever to
the
&P
position before starting the
engine the next time. If the engine is
started with the shift lever in the
&N
position, then it may not be possible to
drive the vehicle even when the shift
lever is moved to the
&A↔&M
or
&R
position. If this occurs, the SHIFT
&P
warning appears on the vehicle infor-
mation display. (
“SHIFT “P”
WARNING” page 2-40)
CAUTION
If the engine was stopped soon when
the engine is hot, the cooling fan may
operate for approximately 2 minutes
after the engine was stopped to cool
the components in the engine compart-
5-12
Starting and driving
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 190 of 311
Black plate (185,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Shift lever operation
Push the button while depressing the brake
pedal.Push the button.Just move the shift lever.Automatically returns.
&Pposition:
Use this position for parking and starting the
engine. The ignition switch will be changed to
the OFF or LOCK position.
CAUTION
Use the
&P
position only when the
vehicle is completely stopped.
&Rposition:
Use this position for driving in reverse.&Nposition:
Neither forward nor reverse gear is engaged.&A↔&M
position:
Use this position for all normal forward driving.
The shift lever can be moved between
&Aand
&M
to alternately change each other. The position indicator indicates the gear position
with the indication of “A” or “M”.
.
&A
position: Use this position for ordinary
driving, with the gears shifted automatically
from first gear to sixth gear according to the
speed and driving conditions.
.
&M
position: Operate the paddle shifter to
drive in first gear to sixth gear as desired.
CAUTION
Grip the shift lever correctly when
operating it. Failure to do so may cause
a finger or other items to be trapped
between the lever and gate, possibly
causing an accident.
NOTICE
. Be sure to observe the following
precautions. Failure to do so may
result in shift lever malfunction.
— Do not spill water, beverages or
other liquids on the shift lever.
Starting and driving
5-15
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 191 of 311
Black plate (186,1)
Model "R35-D" EDITED: 2008/ 5/ 20
— Do not allow sand or similarsubstances to contact the shift
lever.
. Develop the habit of performing the
operations marked with “
”
without pressing the button. If the
button is pressed at these times,
there is the possibility that the lever
could accidentally enter the
&Por
&R
positions.
. When the vehicle is hot, the area
around the shift lever may be hot or
may produce an unusual sound,
however this does not indicate that
there is a malfunction.
NOTE:.When moving the shift lever out of the
&Pposition, it may not be possible to
move the shift lever if the button is
pressed before the brake pedal is
depressed. Press the button only after
depressing the brake pedal.
. Do not place coins or other small
objects in the area around the shift
lever. These objects may get stuck in
the shift gate and prevent the shift
lever from moving into a position.
Sometimes, you may not be able to retrieve these objects.
. Immediately after a cold start, while the
transmission system check display (“T/
M SYSTEM CHECK IN PROCESS”)
appears on the vehicle information
display, the shift lever cannot be moved
out of the
&Pposition. This is because a
check of the transmission system is in
progress. This does not indicate that
there is a malfunction. Move the shift
lever after the message on the vehicle
information display turns off.
. The shift lever knob and console-
mounted shift indicator have a genuine
leather finish that requires proper care
and maintenance. (
“CLEANING IN-
TERIOR” page 7-4)
Shift lock releaseIf the battery charge is low or discharged, the
shift lever may not be moved from the
&P
position even with the brake pedal depressed
and the shift lever button pushed.
To move the shift lever, perform the following
procedure.
1. Push the ignition switch to the OFF or LOCK position.
2. Apply the parking brake.
3. Remove the shift lock cover using a suitable tool wrapped with a cloth.
4. Push down the shift lock as illustrated.
5-16
Starting and driving
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 192 of 311
Black plate (187,1)
Model "R35-D" EDITED: 2008/ 5/ 20
5. Push the shift lever button and move theshift lever to the
&N
position while holding
down the shift lock.
Push the ignition switch to the ON position to
unlock the steering wheel. Now the vehicle may
be moved to the desired location.
If the battery is discharged completely, the
steering wheel cannot be unlocked. Do not
move the vehicle with the steering wheel locked.
NOTICE
If the shift lever cannot be moved out of
the
&P
position after performing the
shift lock release procedure, immedi-
ately have the vehicle inspected by a
GT-R certified NISSAN dealer.
Adaptive shift controlThe adaptive shift control system automatically
operates when the transmission is in the
&A
position and selects an appropriate gear de-
pending on the road conditions such as uphill,
downhill or curving roads.Control on uphill and curving roads:A low gear is maintained that suits the degree of
the slope or curve to allow smooth driving with a
small number of shifts.
Control on downhill roads:The adaptive shift control system shifts to a low
gear that suits the degree of the slope, and uses
the engine brake to reduce the number of times
that the foot brake must be used.Control on winding roads:A low gear is maintained on continuous curves
that involve repeated acceleration and decelera-
tion, so that smooth acceleration is available
instantly when the accelerator pedal is de-
pressed.NOTE:Adaptive shift control may not operate
when the transmission oil temperature is
low immediately after the start of driving
or when it is very hot. If this occurs, switch
to the
&M
position and downshift if neces-
sary.
&M
position
Changing to the
&M
position:
To change to the
&M
position from the
&A
position, either move the shift lever to the
&M
side or operate the paddle shifter. The position
indicator indicates the gear position with the
indication of “M”.
If the paddle shifter is used, the first operation
changes from the
&Aposition to the
&Mposition,
and the second and later operations change the gears.
To return to the
&Aposition, move the shift lever
to the
&M
side again. The position indicator
indicates the gear position with the indication of
“A”.
Starting and driving
5-17
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 194 of 311
Black plate (189,1)
Model "R35-D" EDITED: 2008/ 5/ 20
GearMPH (km/h)
1st 35 (57)
2nd 62 (101)
3rd 90 (145)
4th —
5th —
6th —
DRIVING TIPSAfter starting the engine, fully depress the foot
brake pedal and push the shift lever button
before shifting the shift lever from the
&Pposition
to the
&R,&N,or
&A↔&M
position. Be sure the
vehicle is fully stopped before attempting to shift
the shift lever.
The transmission is designed so that the foot
brake pedal must be depressed before shifting
from
&Pto any other position.
The shift lever cannot be moved out of the
&P
position and into any other position with the
ignition switch other in the LOCK, OFF or ACC
position.When accelerating from a stopKeep the foot brake pedal depressed and push
the shift lever button to shift into a driving gear
as following:
. To drive forward, move the shift lever to the
&A↔&M
position.
. To back up, move the shift lever to the
&R
position.
Starting on level ground:1. Check the shift lever position indicator on
the instrument panel to confirm that the
driving gear is selected.
2. Release the parking brake.
3. Release the foot brake pedal, then gradually depress the accelerator pedal to start the
vehicle in motion.Starting on an uphill:1. Check the shift lever position indicator onthe instrument panel to confirm that the
driving gear is selected.NOTE:When starting or driving on a steep uphill
grade, shift to the
&M
position and operate
the paddle shifter to shift down to 1st gear
as a manual transmission vehicle.
2. With the parking brake applied, slowly release the foot brake pedal.
3. Slowly depress the accelerator pedal and feel the vehicle starting motion with the
parking brake applied.
4. Release the parking brake and gradually depress the accelerator pedal to start the
vehicle in motion.
NOTICE
To prevent stalling or transmission
damage, start in 1st gear. The
&M
position 2nd gear can be used to start
moving the vehicle only when reduced
torque is necessary on snowy roads or
extremely slippery surfaces.NOTE:The hill start assist function operates when
the vehicle is accelerating from a stop on
an uphill. (
“HILL START ASSIST” page
5-31)
When driving the vehicle
WARNING
Do not move the shift lever to the
&N
position while driving. Doing so may
result in an accident due to loss of
engine braking. It may also damage the
transmission.
Starting and driving
5-19
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 196 of 311
Black plate (191,1)
Model "R35-D" EDITED: 2008/ 5/ 20
serious injury.
NOTICE
When the vehicle is stopped on a hill,
do not hold the vehicle in place by
depressing the accelerator pedal. Doing
so may cause the clutch to overheat and
result in transmission damage. Use the
brakes to prevent the vehicle from
moving.When parking the vehicle1. Bring the vehicle to a complete stop.
2. With the foot brake pedal depressed, applythe parking brake.
3. Move the shift lever to the
&Pposition.
4. Check the shift lever position indicator on the instrument panel to confirm that the
&P
position is selected.
5. Push the ignition switch to stop the engine.
WARNING
Before exiting the vehicle, be sure to
move the shift lever to the
&Pposition
and stop the engine. If the engine is
running and the shift lever is not in the
&Pposition, the vehicle may start mov-
ing due to partial engagement of the
clutch or to the effects of gravity on a
slope, or the vehicle may suddenly
accelerate due to accidental operation
of the accelerator pedal, possibly caus-
ing an accident.
The control of the dual clutch transmission,
Bilstein DampTronic
®electronically controlled
shock absorbers and Vehicle Dynamic Control
(VDC) can be changed to the desired modes by
operating the setup switches. Select the desired
mode best suited to the driving conditions.
NOTE:Bilstein DampTronic
®is a registered trade-
mark of ThyssenKrupp Bilstein Suspen-
sion GmbH.
Starting and driving
5-21
VDC, TRANSMISSION AND
SUSPENSION SETUP SWITCHES
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 197 of 311
Black plate (192,1)
Model "R35-D" EDITED: 2008/ 5/ 20
1. Transmission setup switch
2. Suspension setup switch
3. Vehicle Dynamic Control (VDC) setup switchHOW TO SWITCH THE MODESMove the VDC, transmission and suspension
setup switches up or down to change the mode
when the engine is running.R modePush up the VDC, transmission and suspension
setup switches for more than 1 second.SNOW mode and COMF modePush down the transmission and suspension
setup switches.
VDC OFF modePush down the VDC setup switch for more than
1 second.Normal modePush the VDC, transmission and suspension
setup switches to the side opposite from the
selected modes.NOTE:.When the ignition switch is pushed to
the ON position, the VDC, transmission
and suspension set up switch indica-
tors may come on momentarily, but this
does not indicate that there is a mal-
function.
. The VDC, transmission and suspension
setup switches will return to the normal
mode when the engine is restarted.
Also, the transmission setup switch will
return to the normal mode when the
shift lever is moved between
&Aand
&M
while operating the transmission setup
switch.
5-22
Starting and driving
, Q I R U P D W L R Q 3 U R Y L G H G E \