ignition NISSAN NOTE 2016 Service Repair Manual

TM-92
< SYSTEM DESCRIPTION >[CVT: RE0F11A]
DIAGNOSIS SYSTEM (TCM)
• When the self-diagnosis result is acceptable at the 2nd
trip (conforming to driving condition B), DTC of the
1st trip is erased.
COUNTER SYSTEM LIST
DRIVING CONDITION
Driving condition A
Driving condition A is the driving condition that provides warm-up.
In specific, count-up is performed when all of the following conditions are satisfied.
• Engine speed is 400 rpm or more.
• After start of the engine, the water temperature increased by 20 °C (36 °F) or more.
• Water temperature was 70 °C (158 °F) or more.
• The ignition switch was changed from ON to OFF.
NOTE:
• If the same malfunction is detected regardless of the driving condition, reset the A counter.
• When the above is satisfied without detecting t he same malfunction, count up the A counter.
• When MIL goes off due to the malfunction and the A counter reaches 40, the DTC is erased.
Driving condition B
Driving condition B is the driving c ondition that performs all diagnoses once.
In specific, count-up is performed when all of the following conditions are satisfied.
• Engine speed is 400 rpm or more.
• Water temperature was 70 °C (158 °F) or more.
• In closed loop control, vehicle speed of 70 – 120 km/h (43 – 75 MPH) continued for 60 seconds or more.
• In closed loop control, vehicle speed of 30 – 60 km/h (19 – 37 MPH) continued for 10 seconds or more.
• In closed loop control, vehicle speed of 4 km/h (2 MPH) or less and idle determination ON continued for 12 seconds or more.
• After start of the engine, 22 minutes or more have passed.
• The condition that the vehicle speed is 10km/h (6 MPH) or more continued for 10 seconds or more in total.
• The ignition switch was changed from ON to OFF.
NOTE:
• If the same malfunction is detected regardless of the driving condition, reset the B counter.
• When the above is satisfied without detecting t he same malfunction, count up the B counter.
• When the B counter reaches 3 wit hout malfunction, MIL goes off.
• When the B counter is counted once without detecting the same malfunction after TCM memorizes DTC of
the 1st trip, DTC of the 1st trip is erased.
Item Driving conditionTrip
MIL (OFF) B3
DTC (clear) A40
DTC at 1st trip (clear) B1
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-94
< SYSTEM DESCRIPTION >[CVT: RE0F11A]
DIAGNOSIS SYSTEM (TCM)
SELF DIAGNOSTIC RESULTS
Display Item List
Refer to
TM-110, "DTC Index".
DTC at 1st trip and method to read DTC
• DTC (P0705, P0711, P0720, etc.) is specified by SAE J2012/ISO 15031-6.
• DTC and DTC at 1st trip are displayed on “Self Diagnostic results” of CONSULT.
When DTC is currently detected, “CRNT” is displayed. If “PAST” is displayed, it shows a malfunction
occurred in the past.The trip number of drive without malfunction of concerned DTC can be confirmed with
“IGN counter” inside “FFD”.
• When the DTC at the 1st trip is detected, the “timing” is displayed as “1t”.
DTC deletion method
NOTE:
• If the battery terminal is disconnected, the TCM memory is erased. (The disconnection time varies from sev- eral seconds to several hours.
• If the ignition switch is left ON after repair, turn OFF the ignition switch and wait for 10 seconds or more.
Then, turn the ignition ON again. (Engine stop)
1. Touch “TRANSMISSION” of CONSULT.
2. Touch “Self Diagnostic Result”.
3. Touch “Erase”. (DTC memorized in TCM is erased.)
IGN counter
The ignition counter is displayed in “FFD” and the number of times of satisfied “Driving condition A” is dis-
played after normal recovery of DTC. Refer to TM-91, "
DIAGNOSIS DESCRIPTION : Counter System".
• If malfunction (DTC) is currently detected, “0” is displayed.
• After normal recovery, every time “Driving condition A” is satisfied, the display value increases from 1 → 2 →
3...38 → 39.
• When MIL turns OFF due to the malfunction and t he counter reaches 40, the DTC is erased.
NOTE:
The counter display of “40” cannot be checked.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
× : Application : Optional selection
CAN Diagnosis Support Mon-
itor It monitors the status of CAN communication.
ECU Identification Display the ECU identification nu mber (part number etc.) of the selected system.
CALIB DATA The calibration data status of TCM can be checked.
Conditions
Function
Monitored item(Unit)Monitor item selection
Remarks
MAIN SIG-
NALS ECU IN-
PUT SIG- NALS
VSP SENSOR (km/h or mph) ×Displays the vehicle speed calculated from the CVT out-
put shaft speed.
ESTM VSP SIG (km/h or mph) ×Displays the vehicle spee
d signal (ABS) received
through CAN communication.
PRI SPEED SEN (rpm) ×Displays the primary pulley speed calculated from the
pulse signal of the primary speed sensor.
SEC REV SENSOR (rpm) ×Displays the secondary pulley speed calculated from the
pulse signal of the secondary speed sensor.
VHCL/S SE (REV) (rpm) ×Displays the CVT output shaft speed calculated from the
pulse signal of the output speed sensor.
ENG SPEED SIG (rpm) ×Displays the engine speed received through CAN com-
munication.
Revision: August 2015
2016 Versa Note

cardiagn.com

TCM
TM-99
< ECU DIAGNOSIS INFORMATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ECU DIAGNOSIS INFORMATION
TCM
Reference ValueINFOID:0000000012431033
CONSULT DATA MONITOR STANDARD VALUE
• In CONSULT, electric shift timing or lock-up timing, i. e. operation timing of each solenoid valve, is displayed.
Therefore, if there is an obvious difference between t he shift timing estimated from a shift shock (or engine
speed variations) and that shown on the CONSULT, the mechanism parts (including the hydraulic circuit)
excluding the solenoids and sensors may be malfunctioning. In this case, check the mechanical parts follow-
ing the appropriate diagnosis procedure.
• Shift point (gear position) displayed on CONSULT slight ly differs from shift pattern described in Service Man-
ual. This is due to the following reasons.
- Actual shift pattern may vary slightly within specified tolerances.
- While shift pattern described in Service Manual indica tes start of each shift, CONSULT shows gear position
at end of shift.
- The solenoid display (ON/OFF) on CONSULT is changed at the start of gear shifting. In contrast, the gear
position display is changed at the time when gear shif ting calculated in the control unit is completed.
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item ConditionValue/Status (Approx.)
VSP SENSOR While driving Almost same as the speedometer display.
ESTM VSP SIG While driving Almost same as the speedometer display.
PRI SPEED SEN In driving (lock-up ON) A value obtained from dividing engine
speed by counter gear ratio
SEC REV SENSOR Auxiliary gearbox: 1GR
Approximately twice the “VHCL/S SE
(REV)”
Auxiliary gearbox: 2GR Almost same as the “VHCL/S SE (REV)”
VHCL/S SE (REV) Auxiliary gearbox: 1GR
Approximately half of the “SEC REV SEN-
SOR”
Auxiliary gearbox: 2GR Almost same as the “SEC REV SENSOR”
ENG SPEED SIG Engine running Almost same reading as tachometer
LINE PRESSURE SEN • Selector lever: “N” position
•At idle
0.88 – 0.92 V
AT F T E M P S E N CVT fluid: Approx. 20
°C (68 °F) 2.01 – 2.05 V
CVT fluid: Approx. 50 °C (122 °F) 1.45 – 1.50 V
CVT fluid: Approx. 80 °C (176 °F) 0.90 – 0.94 V
G SENSOR Vehicle is level 2.5 V
VIGN SEN Ignition switch: ON 10 – 16 V
VEHICLE SPEED While driving Almost same as the speedo meter display.
INPUT REV In driving (lock-up ON) Almost same as the engine speed.
PRI SPEED In driving (lock-up ON) A value obtained from dividing engine
speed by counter gear ratio
SEC SPEED Auxiliary gearbox: 1GR
Approximately twice the “OUTPUT REV”
Auxiliary gearbox: 2GR Almost same as “OUTPUT REV”
OUTPUT REV Auxiliary gearbox: 1GR
Approximately half of “SEC SPEED”
Auxiliary gearbox: 2GR Almost same as “SEC SPEED”
ENG SPEED Engine running Almost same reading as tachometer
SLIP REV While driving Engine speed − Input speed
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-100
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F11A]
TCM
TOTAL GEAR RATIOAuxiliary gearbox: 1GR
Counter gear ratio
×Pulley ratio Auxiliary
gearbox gear ratio
Auxiliary gearbox: 2GR Counter gear ratio ×Pulley ratio
PULLEY GEAR RATIO In driving (forward)
2.20 − 0.55
In driving (reverse) 2.20
AUX GEARBOX Vehicle started with selector lever in “L” position
1st
Release the accelerator pedal after the follow-
ing conditions are satisfied
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 50 km/h (31 MPH) or more 2nd
In gear shifting of auxiliary gearbox 1st ⇔ 2nd
G SPEED Vehicle stopped
0.00 G
During acceleration The value changes to the positive side
along with acceleration.
During deceleration The value changes to the positive side
along with deceleration.
ACCEL POSI SEN 1 Accelerator pedal released
0.00 deg
Accelerator pedal fully depressed 80.00 deg
VENG TRQ While driving The value changes along with acceleration/
deceleration.
PRI TRQ While driving The value changes along with acceleration/
deceleration.
TRQ RTO While driving The value changes along with acceleration/
deceleration.
LINE PRESSURE Selector lever: “P” position 0.575 MPa
FLUID TEMP Ignition switch ON. Displays the CVT fluid temperature.
DSR REV While driving It varies along with the driving condition.
TRGT GEAR RATIO While driving It varies along with the driving condition.
TGT PLLY GR RATIO In driving (forward)
2.20 − 0.55
In driving (reverse) 2.20
TRGT AUX GEARBOX Vehicle started with selector lever in “L” position
1st
Release the accelerator pedal after the follow-
ing conditions are satisfied
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 50 km/h (31 MPH) or more 2nd
In gear shifting of auxiliary gearbox Display gear position after gear shifting
LU PRS • Engine started
• Vehicle is stopped.
−
0.500 MPa
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 20 km/h (12 MPH) or more 0.450 MPa
LINE PRS • After engine warm up
• Selector lever: “N” position
•At idle
0.500 MPa
• After engine warming up
• Selector lever: “D” position
• Depress the accelerator pedal fully 4.930 – 5.430 MPa
TRGT PRI PRESSURE • Selector lever: “L” position
• Vehicle speed: 20 km/h (12 MPH) 0.325 MPa
Monitor item
ConditionValue/Status (Approx.)
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-102
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F11A]
TCM
INDDRNGSelector lever: “D” position
On
Other than the above Off
INDNRNG Selector lever: “N” position
On
Other than the above Off
INDRRNG Selector lever: “R” position
On
Other than the above Off
INDPRNG Selector lever: “P” position
On
Other than the above Off
CVT LAMP In overdrive OFF
On
Other than the above Off
SPORT MODE IND In overdrive OFF
On
Other than the above Off
MMODE IND Always Off
VDC ON Always Off
TCS ON Always Off
ABS FAIL SIGNAL When ABS malfunction signal is received
On
Other than the above Off
ABS ON ABS is activated
On
Other than the above Off
RANGE Selector lever: “P”
and “N” positions N/P
Selector lever: “R” position R
Selector lever: “D” posi tion (OD OFF indicator
lamp OFF) D
Selector lever: “D” posi tion (OD OFF indicator
lamp ON) S
Selector lever: “L” position L
M GEAR POS Always 1
G SEN SLOPE Flat road
0%
Uphill gradient The value changes to the positive side
along with uphill gradient. (Maximum
40.45%)
Downhill gradient The value changes to the negative side
along with downhill gradient. (Minimum
−
40.45%)
ENGBRKLVL When the engine brake level of “ENGINE
BRAKE ADJ”. in “Work Support” is ON
On
When the engine brake level of “ENGINE
BRAKE ADJ”. in “Work Support” is OFF Off
PVIGN VOLT Ignition switch: ON 10 – 16 V
TRGT AUX GR RATIO Vehicle started with selector lever in “L” position
1.80
Release the accelerator pedal after the follow-
ing conditions are satisfied
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 50 km/h (31 MPH) or more 1.00
G SEN CALIBRATION When G sensor calibration is completed
DONE
When G sensor calibration is not completed YET
Monitor item
ConditionValue/Status (Approx.)
Revision: August 2015 2016 Versa Note

cardiagn.com

TCM
TM-103
< ECU DIAGNOSIS INFORMATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*: These monitor items do not use.
TERMINAL LAYOUT
INPUT/OUTPUT SIGNAL STANDARD
N IDLE STATUS When idle neutral control is operated On
When idle neutral control is not operated
Off
CVT-B* ——
CVT-A* ——
Monitor item
ConditionValue/Status (Approx.)
JSDIA2713ZZ
Te r m i n a l N o .
(Wire color) Description
ConditionValue (Approx.)
+ − Signal Input/
Output
2
(R/B) Ground L range switch Input
Ignition
switch
ONSelector lever:
“L” position 10 − 16 V
Other than the above 0 V
4
(W/B) Ground D range switch Input Selector lever:
“D” position 10 − 16 V
Other than the above 0 V
5
(L/B) Ground N range switch Input Selector lever:
“N” position 10 − 16 V
Other than the above 0 V
6
(O) Ground R range switch Input Selector lever:
“R” position 10 − 16 V
Other than the above 0 V
7
(Y) Ground P range switch Input Selector lever:
“P” position 10 − 16 V
Other than the above 0 V
11
(LG) Ground Sensor ground Input
Always0 V
12
(G/W) Ground
CVT fluid tempera-
ture sensor IntputIgnition
switch
ON CVT fluid: Approx. 20
°C 2.01 – 2.05 V
CVT fluid: Approx. 50 °C 1.45 – 1.50 V
CVT fluid: Approx. 80 °C 0.90 – 0.94 V
14
(G/R) Ground G sensor
InputIgnition
switch
ON When the vehicle stops on
a flat road
2.5 V
15* (V) —— — —
—
16
(L/R) Ground Secondary pres-
sure sensor
Input• Selector lever: “N” position
• At idle
0.88 – 0.92 V
21
(R/W) —
ROM ASSY
(CHIP SELECT) ——
—
22
(V) —R
OM ASSY
(D A

TA I/O) ——
—
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-104
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F11A]
TCM
23
(P/L) —CAN-L
Input/
Output ——
24
(BR) Ground Output speed sen-
sor
Input• Selector lever:
“L” position
• Vehicle speed: 20 km/h (12 MPH) 200 Hz
26
(O/W) Ground Sensor power sup-
ply OutputIgnition switch: ON
5.0 V
Ignition switch: OFF 0 V
30
(BR/B) GroundLine pressure sole-
noid valve
Output• After engine warming up
• Selector lever:
“N” position
• At idle
• After engine warming up
• Selector lever: “D” position
• Depress the acce lerator pedal fully
31
(L/W) —
ROM ASSY
(CLOCK) ——
—
33
(L/G) —CAN-H Input/
Output ——
34
(W) Ground Secondary speed
sensor
Input• Selector lever:
“L” position
• Vehicle speed: 20 km/h (12 MPH) 700 Hz
35
(LG/R) GroundPrimary speed sen-
sor Input• Selector lever:
“L” position
• Vehicle speed: 20 km/h (12 MPH) 1,100 Hz
Te r m i n a l N o .
(Wire color) Description
ConditionValue (Approx.)
+ − Signal Input/
Output
JSDIA1904GB
JSDIA1897GB
JSDIA1898GB
JSDIA1905GB
JSDIA1906GB
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-106
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F11A]
TCM
*: This harness is not used.
Fail-safeINFOID:0000000012431034
TCM has a fail-safe mode. The mode functions so that
operation can be continued even if the signal circuit of
the main electronically contro lled input/output parts is damaged.
If the vehicle shows following behaviors including “poor acceleration”, a malfunction of the applicable system
is detected by TCM and the vehicle may be in a fail-sa fe mode. At this time, check the DTC code and perform
inspection and repair according to the malfunction diagnosis procedures.
Fail-safe function
40
(Y/B) Ground Primary pressure
solenoid valve Output• Selector lever:
“L” position
• Vehicle speed: 20 km/h (12 MPH)
41
(B) Ground Ground
OutputAlways 0 V
42
(B) Ground Ground
OutputAlways 0 V
45
(LG) Ground Battery power sup-
ply (memory back-
up) Input
Always 10 − 16 V
46
(LG) Ground Battery power sup-
ply (memory back-
up)
Input
Always 10 − 16 V
47
(R/W) Ground
Ignition power sup-
ply InputIgnition switch: ON
10 − 16 V
Ignition switch: OFF 0 V
48
(R) Ground
Ignition power sup-
ply InputIgnition switch: ON
10 − 16 V
Ignition switch: OFF 0 V
Te r m i n a l N o .
(Wire color) Description
ConditionValue (Approx.)
+ − Signal Input/
Output
JSDIA1897GB
DTC Vehicle behavior Conditions of vehicle
P062F Not changed from normal driving —
P0705 • Shift position indicator on combination meter is not dis-
played.
• Selector shock is large
•Start is slow
• Acceleration is slow
• Lock-up is not performed —
P0706 • Shift position indicator on combination meter is not dis-
played.
• Selector shock is large
•Start is slow
• Acceleration is slow
• Lock-up is not performed —
Revision: August 2015
2016 Versa Note

cardiagn.com

TM-110
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F11A]
TCM
DTC Index
INFOID:0000000012431037
NOTE:
• If multiple malfunction codes are detected at the same time, check each code according to the “DTC check
priority list”. TM-109, "
DTC Inspection Priority Chart".
• The ignition counter is displayed in “FFD”. Refer to TM-93, "
CONSULT Function".
2P0740 TORQUE CONVERTER
TM-167
P0743 TORQUE CONVERTERTM-169
P0962 PC SOLENOID ATM-184
P0963 PC SOLENOID ATM-186
P0966 PC SOLENOID BTM-189
P0967 PC SOLENOID BTM-191
P0998 SHIFT SOLENOID FTM-193
P0999 SHIFT SOLENOID FTM-195
P099B SHIFT SOLENOID GTM-197
P099C SHIFT SOLENOID GTM-199
3P0890 TCM TM-182
4P062F EEPROM
TM-143
P0705 T/M RANGE SENSOR ATM-144
P0706 T/M RANGE SENSOR ATM-150
P0711 FLUID TEMP SENSOR ATM-153
P0712 FLUID TEMP SENSOR ATM-157
P0713 FLUID TEMP SENSOR ATM-159
P0715 INPUT SPEED SENSOR ATM-161
P0847 FLUID PRESS SEN/SW BTM-177
P0848 FLUID PRESS SEN/SW BTM-179
P1586 G SENSORTM-201
P1588 G SENSORTM-204
P2765 OUTPUT SPEED SENSORTM-206
5P0720 OUTPUT SPEED SENSOR TM-164
6P0746 PC SOLENOID A
TM-173
P2857 CLUTCH B PRESSURETM-209
P2858 CLUTCH A PRESSURETM-210
P2859 CLUTCH A PRESSURE TM-211
P285A CLUTCH B PRESSURETM-213
7P0744 TORQUE CONVERTER
TM-171P0846 FLUID PRESS SEN/SW BTM-175
P0965 PC SOLENOID BTM-188
PriorityDTC (Diagnostic Trouble Code) Reference
DTC*1, *2
Items
(CONSULT screen terms) Trip MILPermanent
DTC
group
*3Reference
GST CONSULT
(TRANSMISSION)
P062F P062F EEPROM 1ON B TM-143
P0705P0705 T/M RANGE SENSOR A 2ON B TM-144
P0706P0706 T/M RANGE SENSOR A 2ON B TM-150
P0711P0711 FLUID TEMP SENSOR A 2ON A TM-153
Revision: August 2015 2016 Versa Note

cardiagn.com

ADDITIONAL SERVICE WHEN REPLACING TCMTM-125
< BASIC INSPECTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ADDITIONAL SERVICE WHEN REPLACING TCM
DescriptionINFOID:0000000012431042
When replacing the TCM, perform the following work. For work procedure, refer to TM-125, "Work Procedure".
TCM PROGRAMMING• Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.
CAUTION:
When replacing TCM, save TCM data on CONSULT before removing TCM.
LOADING AND STORING OF CALIBRATION DATA• The TCM acquires calibration data (individual characteristic value) of each solenoid that is stored in the
ROM assembly (in the control valve). This enables the TCM to perform accurate control. After the TCM is
replaced, check that the calibrati on data is correctly loaded and stored.
CALIBRATION OF G SENSOR
• TCM stores calibration data (inherent characteristic value) of G sensor to provide accurate control. There-
fore, it is required to perform calibration of G sensor after the replacement of TCM.
CAUTION:
When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and
then replace TCM.
Work ProcedureINFOID:0000000012431043
1.CHECK NEW TCM PART NUMBER
Check new TCM part number to see whether it is blank TCM or not.
NOTE:
• Part number of blank TCM is 310F6-XXXXX.
• Check the part number when ordering TCM or with the one included in the label on the container box.
Is the new TCM a blank TCM?
YES >> GO TO 2.
NO >> GO TO 3.
2.SAVING TCM DATA (VEHICLE SPECIFICATIONS)
NOTE:
Save necessary data stored in TCM in CONSULT according to the following instructions: With CONSULT
1. Turn ignition switch OFF.
2. Turn ignition switch ON.
3. Select “Re/programming, Configuration”.
4. Select “AT/CVT”.
NOTE:
If “AT/CVT” is not displayed and TCM data cannot be saved on CONSULT, GO TO 3.
5. Select “Programming”.
6. Save TCM data on CONSULT according to the CONSULT display.
>> GO TO 3.
3.REPLACE TCM
1. Turn ignition switch OFF and wait for 10 seconds.
2. Replace TCM. Refer to TM-239, "
Removal and Installation".
>> GO TO 4.
4.LOAD CALIBRATION DATA
1. Shift the selector lever to the “P” position.
2. Turn ignition switch ON.
3. Check that "P" is displayed on shift position indicator on combination meter. NOTE:
Revision: August 2015 2016 Versa Note

cardiagn.com