cvt NISSAN NOTE 2016 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 2925 of 3641
![NISSAN NOTE 2016 Service Repair Manual SEC-68
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2601 SHIFT POSITION
B2601 SHIFT POSITION
DTC LogicINFOID:0000000012430381
DTC DETECTION LOGIC
NOTE:
• If DTC B2601 is displayed with DT](/img/5/57363/w960_57363-2924.png "NISSAN NOTE 2016 Service Repair Manual SEC-68
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2601 SHIFT POSITION
B2601 SHIFT POSITION
DTC LogicINFOID:0000000012430381
DTC DETECTION LOGIC
NOTE:
• If DTC B2601 is displayed with DT")
SEC-68
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2601 SHIFT POSITION
B2601 SHIFT POSITION
DTC LogicINFOID:0000000012430381
DTC DETECTION LOGIC
NOTE:
• If DTC B2601 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
BCS-63, "
DTC Logic".
• If DTC B2601 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-64, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Shift the selector lever to the P position.
2. Turn ignition switch ON and wait 2 seconds or more.
3. Shift the selector lever to any position other than P and wait 2 seconds or more.
4. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES >> Go to SEC-68, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000012430382
Regarding Wiring Diagram information, refer to SEC-37, "Wiring Diagram".
1.CHECK CVT SHIFT SELECTOR CIRCUIT (BCM)
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector (park position switch) connector.
3. Disconnect BCM connector.
4. Check continuity between CVT shift selector (p ark position switch) harness connector and BCM harness
connector.
5. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness.
DTC No. Trouble diagnosis name DTC detecting conditionPossible cause
B2601 SHIFT P SIGNAL When there is a difference between P range
signal from CVT shift selector (park position
switch) and P position signal from IPDM E/R
(CAN). • Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors [CVT shift selector (park position
switch) circuit is open or shorted.]
• IPDM E/R
•BCM
CVT shift selector (park position switch) BCM
Continuity
Connector TerminalConnector Terminal
M38 8M97 37Yes
CVT shift selector (park position switch) GroundContinuity
Connector Terminal
M38 8 No
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2926 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2601 SHIFT POSITIONSEC-69
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
2.CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)
1. Disconnect IPDM E/R connector.
2.](/img/5/57363/w960_57363-2925.png "NISSAN NOTE 2016 Service Repair Manual B2601 SHIFT POSITIONSEC-69
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
2.CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)
1. Disconnect IPDM E/R connector.
2.")
B2601 SHIFT POSITIONSEC-69
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
2.CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)
1. Disconnect IPDM E/R connector.
2. Check continuity between CVT shift selector (par k position switch) harness connector and IPDM E/R har-
ness connector.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of al l Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
3. Perform DTC CONFIRMATION PROCEDURE for DTC B2601. Refer to SEC-68, "
DTC Logic".
Is DTC B2601 detected again?
YES >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation".
NO >> Inspection End.
CVT shift selector (park position switch) IPDM E/R
Continuity
Connector TerminalConnector Terminal
M38 8E47 80Yes
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2927 of 3641
![NISSAN NOTE 2016 Service Repair Manual SEC-70
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
B2602 SHIFT POSITION
DTC LogicINFOID:0000000012430383
DTC DETECTION LOGIC
NOTE:
• If DTC B2602 is displayed with DT](/img/5/57363/w960_57363-2926.png "NISSAN NOTE 2016 Service Repair Manual SEC-70
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
B2602 SHIFT POSITION
DTC LogicINFOID:0000000012430383
DTC DETECTION LOGIC
NOTE:
• If DTC B2602 is displayed with DT")
SEC-70
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
B2602 SHIFT POSITION
DTC LogicINFOID:0000000012430383
DTC DETECTION LOGIC
NOTE:
• If DTC B2602 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
BCS-63, "
DTC Logic".
• If DTC B2602 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-64, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine.
2. Drive vehicle at a speed of 4 km/h (2.5 MPH) or more for 10 seconds or more.
3. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES >> Go to SEC-70, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000012430384
Regarding Wiring Diagram information, refer to SEC-37, "Wiring Diagram".
1.CHECK DTC OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check DTC in “Self Diagnostic Re sult” of “ABS” using CONSULT.
Is DTC detected?
YES >> Perform the trouble diagnosis relat ed to the detected DTC. Refer to BRC-43, "DTC Index".
NO >> GO TO 2.
2.CHECK DTC OF COMBINATION METER
Check DTC in “Self Diagnostic Result” of “METER/M&A” using CONSULT.
Is DTC detected?
YES >> Perform the trouble diagnosis relat ed to the detected DTC. Refer to MWI-24, "DTC Index".
NO >> GO TO 3.
3.CHECK CVT SHIFT SELECTOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector (park position switch) connector.
3. Check voltage between CVT shift selector (park position switch) harness connector and ground.
DTC No. Trouble diagnosis name DTC detecting conditionPossible cause
B2602 SHIFT P DIAG BCM detects the following status for 10 seconds:
• Selector lever is in the P position.
• Vehicle speed is 4 km/h (2.5 MPH) or more.
• Ignition switch is in the ON position. • Harness or connectors
(The CAN communication line is
open or shorted.)
• Harness or connectors [CVT shift selector (park position
switch) circuit is open or shorted.]
• CVT shift selector (park position switch)
• Combination meter
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2928 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2602 SHIFT POSITIONSEC-71
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 4.
4.CHECK CVT SHIFT S](/img/5/57363/w960_57363-2927.png "NISSAN NOTE 2016 Service Repair Manual B2602 SHIFT POSITIONSEC-71
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 4.
4.CHECK CVT SHIFT S")
B2602 SHIFT POSITIONSEC-71
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 4.
4.CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness connector.
3. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
5.REPLACE BCM
1. Replace BCM. Refer to PCS-30, "
Removal and Installation".
2. Perform initialization of BCM and registration of al l Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
6.CHECK CVT SHIFT SELECTOR CIRCUIT
1. Disconnect BCM connector and IPDM E/R connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness connector.
3. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace harness.
7.CHECK CVT SHIFT SELECTOR (PARK POSITION SWITCH)
Refer to SEC-72, "
Component Inspection".
Is the inspection result normal?
(+)
(–)Voltage (V)
(Approx.)
CVT shift selector (park position switch)
Connector Terminal
M38 7GroundBattery voltage
CVT shift selector (park position switch) BCM
Continuity
Connector TerminalConnector Terminal
M38 7M98 104Yes
CVT shift selector (park position switch) GroundContinuity
Connector Terminal
M38 7 No
CVT shift selector (park position switch) BCM
Continuity
Connector TerminalConnector Terminal
M38 8M97 37Yes
CVT shift selector (park position switch) GroundContinuity
Connector Terminal
M38 8 No
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2929 of 3641
![NISSAN NOTE 2016 Service Repair Manual SEC-72
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
YES >> GO TO 8.
NO >> Replace CVT shift selector. Refer to
TM-231, "
Removal and Installation".
8.CHECK INTERMITTENT](/img/5/57363/w960_57363-2928.png "NISSAN NOTE 2016 Service Repair Manual SEC-72
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
YES >> GO TO 8.
NO >> Replace CVT shift selector. Refer to
TM-231, \"
Removal and Installation\".
8.CHECK INTERMITTENT")
SEC-72
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
YES >> GO TO 8.
NO >> Replace CVT shift selector. Refer to
TM-231, "
Removal and Installation".
8.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
Component InspectionINFOID:0000000012430385
1.CHECK CVT SHIFT SELECTOR (PARK POSITION SWITCH)
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Check continuity between CVT shift se lector (park position switch) terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace CVT shift selector. Refer to TM-231, "
Removal and Installation".
CVT shift selector (park position switch)
ConditionContinuity
Terminal
78 Selector lever: P positionSelector button: Released
No
Selector button: Pressed Ye s
Selector lever: Other than P position
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2930 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2603 SHIFT POSITIONSEC-73
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
B2603 SHIFT POSITION
DTC LogicINFOID:0000000012430386
DTC DETECTION LOGIC
NOTE:
•](/img/5/57363/w960_57363-2929.png "NISSAN NOTE 2016 Service Repair Manual B2603 SHIFT POSITIONSEC-73
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
B2603 SHIFT POSITION
DTC LogicINFOID:0000000012430386
DTC DETECTION LOGIC
NOTE:
•")
B2603 SHIFT POSITIONSEC-73
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
B2603 SHIFT POSITION
DTC LogicINFOID:0000000012430386
DTC DETECTION LOGIC
NOTE:
• If DTC B2603 is displayed with DTC B2601, first perform the trouble diagnosis for DTC B2601. Refer to SEC-68, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE 1
1. Shift the selector lever to the P position.
2. Turn ignition switch ON and wait 1 second or more.
3. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES >> Go to SEC-73, "Diagnosis Procedure".
NO >> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE 2
1. Shift the selector lever to the position other than P and N, and wait 1 second or more.
2. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES >> Go to SEC-73, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000012430387
Regarding Wiring Diagram information, refer to SEC-37, "Wiring Diagram".
1.INSPECTION START
Perform inspection in accordance with procedure that confirms DTC.
Which procedure confirms DTC?
DTC confirmation procedure 1>>GO TO 2.
DTC confirmation procedure 2>>GO TO 8.
2.CHECK FUSE
1. Turn power switch OFF.
2. Check that the following fuse in IPDM E/R is not blown.
Is the inspection result normal?
DTC No. Trouble diagnosis name DTC detecting conditionPossible causes
B2603 SHIFT POSITION BCM detects the following status when ignition
switch is in the ON position:
• Transmission range switch signal: approx. 0
V.
• CVT shift selector (park position switch) sig- nal: approx. 0 V. • Harness or connector
[CVT shift selector (park position
switch) circuit is open or shorted.]
• Harness or connectors (Transmission range switch circuit is
open or shorted.)
• CVT shift selector (park position switch)
• Transmission range switch
•BCM
Signal name Fuse No.
Ignition power supply 49 (10 A)
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2932 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2603 SHIFT POSITIONSEC-75
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
YES >> GO TO 7.
NO >> Repair or replace harness.
7.CHECK TRANSMISSION RANGE SWITCH](/img/5/57363/w960_57363-2931.png "NISSAN NOTE 2016 Service Repair Manual B2603 SHIFT POSITIONSEC-75
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
YES >> GO TO 7.
NO >> Repair or replace harness.
7.CHECK TRANSMISSION RANGE SWITCH")
B2603 SHIFT POSITIONSEC-75
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
YES >> GO TO 7.
NO >> Repair or replace harness.
7.CHECK TRANSMISSION RANGE SWITCH
Refer to SEC-76, "
Component Inspection (Transmission Range Switch)".
Is the inspection result normal?
YES >> GO TO 12.
NO >> Replace transmission range switch.
8.CHECK CVT SHIFT SELECTOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector (park position switch) connector.
3. Check voltage between CVT shift selector (p ark position switch) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 10.
NO >> GO TO 9.
9.CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness connector.
3. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 12.
NO >> Repair or replace harness.
10.CHECK CVT SHIFT SELECTOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness connector.
3. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
(+) (–)Voltage (V)
(Approx.)
CVT shift selector (park position switch)
Connector Terminal
M38 7GroundBattery voltage
CVT shift selector (park position switch) BCM
Continuity
Connector TerminalConnector Terminal
M38 7M98 104Yes
CVT shift selector (park position switch) GroundContinuity
Connector Terminal
M38 7 No
CVT shift selector (park position switch) BCM
Continuity
Connector TerminalConnector Terminal
M38 8M97 37Yes
CVT shift selector (park position switch) GroundContinuity
Connector Terminal
M38 8 No
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2933 of 3641
![NISSAN NOTE 2016 Service Repair Manual SEC-76
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2603 SHIFT POSITION
YES >> GO TO 11.
NO >> Repair or replace harness.
11 .CHECK CVT SHIFT SELECTOR
(PARK POSITION SWITCH)
Refer to SEC-](/img/5/57363/w960_57363-2932.png "NISSAN NOTE 2016 Service Repair Manual SEC-76
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2603 SHIFT POSITION
YES >> GO TO 11.
NO >> Repair or replace harness.
11 .CHECK CVT SHIFT SELECTOR
(PARK POSITION SWITCH)
Refer to SEC-")
SEC-76
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2603 SHIFT POSITION
YES >> GO TO 11.
NO >> Repair or replace harness.
11 .CHECK CVT SHIFT SELECTOR
(PARK POSITION SWITCH)
Refer to SEC-76, "
Component Inspection [CVT Shift Selector (Park Position Switch)]".
Is the inspection result normal?
YES >> GO TO 13.
NO >> Replace CVT shift selector. Refer to TM-231, "
Removal and Installation".
12.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
13.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
Component Inspection (T ransmission Range Switch)INFOID:0000000012430388
1.CHECK TRANSMISSION RANGE SWITCH
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Check continuity between transmission range switch terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace transmission range switch.
Component Inspection [CVT Shift Selector (Park Position Switch)]INFOID:0000000012430389
1.CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Check continuity between CVT shift se lector (park position switch) terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace CVT shift selector. Refer to TM-231, "
Removal and Installation".
Transmission range switch
Condition Continuity
Te r m i n a l
71 0P or N position
Yes
Other than above No
CVT shift selector (detention switch)
Condition Continuity
Terminal
78 Selector lever: P positionSelector button: Released No
Selector button: Pressed
Ye s
Selector lever: Other than P position
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2939 of 3641
![NISSAN NOTE 2016 Service Repair Manual SEC-82
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
B2608 STARTER RELAY
DTC LogicINFOID:0000000012430395
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC](/img/5/57363/w960_57363-2938.png "NISSAN NOTE 2016 Service Repair Manual SEC-82
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
B2608 STARTER RELAY
DTC LogicINFOID:0000000012430395
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC")
SEC-82
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
B2608 STARTER RELAY
DTC LogicINFOID:0000000012430395
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
BCS-63, "
DTC Logic".
• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-64, "
DTC Logic".
• If DTC B2608 is displayed with other DTC (BCM), first perform the trouble diagnosis for other DTC detected.\
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under t he following conditions to start engine.
- Selector lever: In the P position
- Brake pedal: Depressed
2. Wait 1 second after engine started.
3. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES >> Go to SEC-82, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000012430396
Regarding Wiring Diagram information, refer to SEC-37, "Wiring Diagram".
1.CHECK DTC OF IPDM E/R
Check DTC in “Self Diagnostic Result” of “IPDM E/R” using CONSULT.
Is DTC detected?
YES >> Perform the trouble diagnosis relat ed to the detected DTC. Refer to PCS-20, "DTCIndex".
NO >> GO TO 2.
2.CHECK STARTER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B2608 STARTER RELAY BCM outputs starter relay OFF signal but
BCM receives starter relay ON signal from
IPDM E/R (CAN). • Harness or connectors
(The CAN communication line is open or
shorted.)
• Harness or connectors (Starter relay circuit is open or shorted.)
•IPDM E/R
• Starter relay
(+)
(–) Condition Voltage (V)
(Approx.)
BCM
Connector Terminal
M98 97 Ground CVT selector lever N or P position Battery voltage
Other than above
0
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2957 of 3641
![NISSAN NOTE 2016 Service Repair Manual SEC-100
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B210C STARTER CONTROL RELAY
B210C STARTER CONTROL RELAY
DTC LogicINFOID:0000000012430422
DTC DETECTION LOGIC
NOTE:
• If DTC B210C is di](/img/5/57363/w960_57363-2956.png "NISSAN NOTE 2016 Service Repair Manual SEC-100
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B210C STARTER CONTROL RELAY
B210C STARTER CONTROL RELAY
DTC LogicINFOID:0000000012430422
DTC DETECTION LOGIC
NOTE:
• If DTC B210C is di")
SEC-100
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B210C STARTER CONTROL RELAY
B210C STARTER CONTROL RELAY
DTC LogicINFOID:0000000012430422
DTC DETECTION LOGIC
NOTE:
• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
BCS-63, "
DTC Logic".
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210C may be detected.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait 1 second or more.
3. Turn ignition switch ON.
4. Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.
Is DTC B210C displayed?
YES >> Refer to SEC-100, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000012430423
Regarding Wiring Diagram information, refer to SEC-37, "Wiring Diagram".
1. PERFORM SELF DIAGNOSTIC RESULT
Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.
Is display history of DTC B210C CRNT?
YES >> GO TO 2.
NO >> Refer to GI-42, "
Intermittent Incident".
2.CHECK STARTER CONTROL RELA Y CONTROL CIRCUITS VOLTAGE
Check voltage between IPDM E/R connectors and ground.
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation".
NO (WITH M/T)>>GO TO 3.
NO (WITH CVT)>>GO TO 4.
CONSULT Display DTC Detection Condition Possible Cause
STR CONT RLY OFF CIRC
[B210C] When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
OFF position for 1 second or more:
• Starter control relay signal (CAN) from BCM.
• Starter relay status signal (CAN) from BCM.
• Starter control relay an
d starter relay status
signal. (IPDM E/R input)
• Starter control relay co ntrol signal. (IPDM E/R
output) • IPDM E/R
•BCM
•Battery
IPDM E/R
GroundVo l ta g e
(Approx.)
Connector Terminal
E44 (WITH M/T) 13
—Battery voltage
F42 (WITH CVT) 40
Revision: August 2015 2016 Versa Note
cardiagn.com