jump cable NISSAN PULSAR 2016 Owners Manual


> (GLW   0RGHO &$@
5-8
Starting anddriving
GUID-CBF21 064-B60B-405D-A4B8-F9 ACF8015B5A
1. Apply theparking brake.
2. Depress thefoot brake pedal.
3. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orªNº
(Neutral) position.
The starter isdesigned tooperate onlywhen
the shift lever isin the proper position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position,
and depress theclutch pedaltothe floor while
starting theengine.
The starter isdesigned tonot operate unless
the clutch pedalisdepressed.
4. Crank theengine withyour footoffthe accelerator
pedal byturning theignition switchtothe ªSTARTº
position.
5. Immediately releasetheignition switchwhenthe
engine starts.Ifthe engine starts,butfails torun,
repeat theabove procedures.
.
If the engine isvery hard tostart inextremely
cold weather orwhen restarting, depressthe
accelerator pedalalittle (approximately 1/3to
the floor) ,hold itand then crank theengine.
Release theaccelerator pedalwhentheengine
starts.
.
If the engine isvery hard tostart because itis
flooded, depresstheaccelerator pedalallthe
way tothe floor andhold it.Crank theengine
for 5-6 seconds. Aftercranking theengine,
release theaccelerator pedal.Cranktheengine
with your footoffthe accelerator pedalby
turning theignition switchtoSTART .Release
the ignition switchwhentheengine starts.Ifthe
engine starts,butfails torun, repeat theabove procedure.
CAUTION:
. Donot operate thestarter formore than15
seconds atatime. Ifthe engine doesnot
start, turntheignition switchoffand wait 10
seconds beforecranking theengine again.
Otherwise, thestarter couldbedamaged.
. Ifitbecomes necessary tostart theengine
with abooster batteryandjumper cables,
the instructions andcautions contained in
the ª6.Incase ofemergencyº sectionshould
be carefully followed.
6. Allow theengine toidle foratleast 30seconds
after starting theengine towarm-up. Driveat
moderate speedsforashort distance first,
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
GUID-27 686CF6-E6E 5-4E98-9C0E-E33A1613D 9C9
1. Apply theparking brake.
2. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orthe ªNº
(Neutral) position.
The starter isdesigned tooperate onlywhen
the shift lever isin the proper position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position.
The starter isdesigned nottooperate unless
the clutch pedalisfully depressed.
The Intelligent Keymust becarried when
operating theignition switch.
3. Push theignition switchtothe ªONº position.
Depress thebrake pedal(CVTmodel) orthe
clutch pedal(MTmodel) andpush theignition
switch tostart theengine.
T o start theengine immediately ,push andrelease
the ignition switchwhiledepressing thebrake
pedal orclutch pedalwiththeignition switchin
any position.
4. Ifthe engine starts,butfails torun, repeat the
above procedures.
.
If the engine isvery hard tostart inextremely
cold weather orwhen restarting, depressthe
accelerator pedalalittle (approximately 1/3to
the floor) ,hold itand then crank theengine.
Release theaccelerator pedalwhentheengine
starts.
.
If the engine isvery hard tostart because itis
flooded, depresstheaccelerator pedalallthe
way tothe floor andhold it.Crank theengine
for 5-6 seconds. Aftercranking theengine,
release theaccelerator pedal.Cranktheengine
with your footoffthe accelerator pedalby
ST ARTING ENGINE (modelwithout
Intelligent Keysystem) ST
ARTING ENGINE (modelwith
Intelligent Keysystem)
&RQGLWLRQ


> (GLW   0RGHO &$@
turning theignition switchtoSTART .Release
the ignition switchwhentheengine starts.Ifthe
engine starts,butfails torun, repeat theabove
procedure.
CAUTION:
. Assoon asthe engine hasstarted, release
the ignition switchimmediately.
. Donot operate thestarter formore than15
seconds atatime. Ifthe engine doesnot
start, pushtheignition switchtothe ªOFFº
position andwait 10seconds beforecrank-
ing the engine again.Otherwise, thestarter
could bedamaged.
. Ifitbecomes necessary tostart theengine
with abooster batteryandjumper cables,
the instructions andcautions contained in
the ª6.Incase ofemergencyº sectionshould
be carefully followed.
5. Allow theengine toidle foratleast 30seconds
after starting theengine towarm-up. Driveat
moderate speedsforashort distance first,
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
6. To stop theengine, movetheshift lever tothe ªPº
(Park) position (CVTmodel) ormove theshift lever
to the ªNº (Neutral) position(MTmodel) ,apply the
parking brakeandpush theignition switchtothe
ªOFFº position.
GUID-FC 8DD999-53 2D-4255-B52B-8544BB F23419
DRIVING WITHCONTINUOUSL YVARI-
ABLE TRANSMISSION (CVT)
GUID-CA 3CA43B-2A 6A-4E78-941 9-61BAC1DD D7EF
The Continuously Variable Transmission (CVT)inyour
vehicle iselectronically controlledtoproduce maximum
power andsmooth operation.
The recommended operatingprocedures forthis
transmission areshown onthe following pages.Follow
these procedures formaximum vehicleperformance
and driving enjoyment.
WARNING:
Do not downshift abruptlyonslippery roads.
This maycause aloss ofcontrol.
CAUTION:
. The cold engine idlespeed ishigh, souse
caution whenshifting thetransmission into
a forward orreverse position beforethe
engine haswarmed up.
. Avoid revving upthe engine whilethe
vehicle isstopped. Thiscould cause unex-
pected vehicle movement.
. Never shifttoeither theªPº (Park) orªRº
(Reverse) positionwhilethevehicle ismov-
ing. This could cause serious damage tothe
transmission.
. Except inan emergency, donot shift tothe
ªNº (Neutral) positionwhiledriving. Coast-
ing with thetransmission inthe ªNº (Neutral)
position maycause serious damage tothe
transmission.
. Start theengine ineither theªPº (Park) or
ªNº (Neutral) position.Theengine willnot
start inany other position. Ifitdoes, have your
vehicle checked byaNISSAN dealer.
. Shift intotheªPº (Park) position andapply
the parking brakewhenatastandstill for
longer thanashort waiting period.
. Keep theengine atidling speed while
shifting fromtheªNº (Neutral) positionto
any driving position.
. When stopping thevehicle onanuphill
grade, donot hold thevehicle bydepressing
the accelerator pedal.Thefoot brake pedal
should bedepressed inthis situation.
Starting vehicle
GUID-9E5 839FD-C45 3-4C86-B65 8-6D40F7F1CF16
1. After starting theengine, fullydepress thefoot
brake pedalbefore moving theshift lever outofthe
ªPº (Park) position.
2. Keep thefoot brake pedaldepressed andmove
the shift lever toadriving position.
3. Release theparking brake,thefoot brake pedal,
and then gradually startthevehicle inmotion.
The CVT isdesigned sothe foot brake pedal
MUST bedepressed beforeshifting fromtheªPº
(Park) position toany driving position whilethe
ignition switchisin the ªONº position.
The shift lever cannot bemoved outofthe ªPº
(Park) position andinto anyofthe other
positions ifthe ignition switchisplaced inthe
ªLOCKº ,ªOFFº orªACCº position orifthe key is
removed.
CAUTION:
. DEPRESS THEFOOTBRAKE PEDAL-Shift-
ing the shift lever toªDº ,ªR º, ªL º or the
manual shiftmode without depressing the
foot brake pedalcauses thevehicle tomove
Starting anddriving
5-9
DRIVING
VEHICLE
&RQGLWLRQ


> (GLW   0RGHO &$@
6-6
In case ofemergency
JVE0108X
1. Ifthe booster batteryisin another vehicle
*
B
,
position thetwo vehicles
*
A
and
*
B
to bring the
batteries intoclose proximity toeach other.
CAUTION:
If the battery ofvehicle
*
A
equipped withthe
Intelligent Keysystem isdischarged, theignition
switch cannot bemoved fromtheªLOCKº
position and,ifthe steering lockisengaged,
the steering wheelcannot bemoved. Connect
the jumper cablestothe booster vehicle
*
B
before turning theignition switchanddisenga-
ging thesteering lock.
2. Apply theparking brake.
3. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªNº (Neutral) position.
4. Switch offallunnecessary electricalsystems
(headlights, heater,airconditioner, etc.).
5. Place theignition switchinthe ªLOCKº position. 6.
Remove thevent caps, ifequipped, onthe battery .
7. Cover thebattery withafirmly wrung outmoist
cloth toreduce thehazard ofan explosion.
8. Connect thejumper cablesinthe sequence as
illustrated (
*
1
,
*
2
,
*
3
,
*
4
) .
CAUTION:
. Always connect positive +topositive +and
negative 7tobody ground, NOTto the
battery's negative7.
. Besure thatthejumper cablesdonot touch
moving partsinthe engine compartment.
. Besure thatthejumper cable's clamps do
not contact anyother metal.
9. Start theengine ofthe booster vehicle
*
B
and let
it run forafew minutes.
10. Depress theaccelerator pedalofthe booster
vehicle
*
B
at about 2,000 rpm.
11. Start theengine ofthe jumped vehicle
*
A
in the
normal manner.
CAUTION:
Never keepthestarter motorengaged formore
than 10seconds. Ifthe engine doesnotstart
right away, placetheignition switchinthe ªOFFº
position andwait atleast 10seconds before
trying again.
12. After theengine isstarted, carefully disconnect
the jumper cablesinthe opposite sequence from
that illustrated (
*
4
,
*
3
,
*
2
,
*
1
) .
13. Remove anddispose ofthe cloth asitmay be
contaminated withcorrosive acid.
14. Replace thevent caps, ifremoved.
&RQGLWLRQ