alarm NISSAN QUEST 2016 RE52 / 4.G Quick Reference Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: QUEST, Model: NISSAN QUEST 2016 RE52 / 4.GPages: 32, PDF Size: 2.43 MB
Page 10 of 32

8
NISSAN INTELLIGENT KEY® SYSTE M
The NISSAN Intelligent Key® System allows you to lock 
or unlock your vehicle, open your liftgate and start the 
engine. It is important to make sure the Intelligent Key 
is with you (that is, in your pocket or purse).
 
    The operating range of the Intelligent Key is 
within 31.5 in (80 cm) from each request switch.
 
    To lock the vehicle, push either door handle 
request switch 
1 or the liftgate request  
switch 
2 or press the  button 3 on the  
key fob.
 
    To unlock the vehicle, perform one of the 
following procedures:
    •  Push either door handle request switch 
1  
or the liftgate request switch 
2; the 
corresponding door will unlock. Push the 
request switch again within 1 minute; all other 
doors will unlock, or
    •  Press the 
 button 4 on the key fob to  
unlock the driver’s side door. Press the 
 
button 
4 again within 1 minute; all other 
doors will unlock.
 
    To open the power liftgate (if so equipped), press 
the 
 button 5 for more than 1 second.
 
    The Intelligent Key can also be used to activate 
the panic alarm by pressing and holding the 
 
button 
6 for more than 1 second. Once activated, the panic alarm and headlights \
will stay on for a period of time. 
INTELLIGENT KEY BATTERY DISCHARGE
 
    If the battery of the Intelligent Key is discharged 
or environmental conditions interfere with 
the Intelligent Key operation, start the engine 
according to the following procedure:
    1.  Move the shift lever to the P (PARK) position.
    2.  Firmly apply the foot brake.
    3.   Touch the ignition switch with the Intelligent 
Key and a chime will sound.
    4.   Within 10 seconds after the chime sounds, push the ignition switch while 
depressing the brake pedal and the engine will start.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving 
(section 5)” and the “Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
1
3
4
5
6
2
FIRST DRIVE FEATURES
1964370_16a_Quest_US_pQRG_090215.indd   89/2/15   11:07 AM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.  
Page 30 of 32

28
HOMELINK® UNIVERSAL TRANSCEIVER (if so equipped)
    The  HomeLink® Universal Transceiver can learn and consolidate the functions of up to 
three different hand-held transmitters, operating items such as garage doors, property 
gates, outdoor and indoor lights or alarm systems.
 
    To program the HomeLink® Universal Transceiver:
    •  Position the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink 
surface, keeping the HomeLink indicator light in view.
    •  Press and hold the desired HomeLink button and the handheld transmitter \
button 
simultaneously until the HomeLink indicator light flashes slowly and then ra\
pidly.
    •  Both buttons may be released when the indicator light flashes rapidly.
 
    To verify the programing is complete, press and hold the HomeLink button \
and 
observe the indicator light:
    •  A solid, continuous light indicates the programing is complete and the H\
omeLink 
button will activate your device.
    •  A blinking light that turns to a solid, continuous light after 2 seconds\
 indicates 
additional steps are required to complete the programing.
 
    An additional person may make the remaining steps easier. To complete the  
programing process:
    •  At the receiver of the device that you are programing to the HomeLink bu\
tton, press 
and release the learn or smart button (the name may vary by manufacture\
r, but it is 
usually located near where the hanging antenna wire is attached to the unit). You 
have approximately 30 seconds to initiate the following step.
    •  Press and hold the programed HomeLink button for 2 seconds and release.
 
     You may have to repeat the previous two steps up to 3 times to complete t\
he 
programing process. HomeLink should now activate your device. 
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink 
website at www.homelink.com or call 1-800-355-3515.
HOMELINK
SYSTEM GUIDE
1964370_16a_Quest_US_pQRG_090215.indd   289/2/15   11:08 AM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.