battery NISSAN TEANA 2003 Service Manual

BL-160
NATS(NISSAN ANTI-THEFT SYSTEM)

4. CHECK BCM FUNCTION
1. Connect security indicator lamp connector.
2. Disconnect BCM connector.
3. Check voltage between BCM connector M3 terminal 23 (L/B)
and ground.
OK or NG
OK >> BCM is malfunctioning.

Replace BCM.

Perform initialization with CONSULT-II.

For initialization, refer to “CONSULT-II Operation
Manual NATS”.
NG >> Check the following.

Harness for open or short between security indicator lamp and BCM.

Indicator lamp condition
Removal and Installation NATS Antenna Amp.BIS000YT
REMOVAL
CAUTION:
Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
1. Remove the steering column cover. Refer to IP-10, "
Component Parts Location" .
2. Disconnect the NATS antenna amp. connector, remove the
screw and NATS antenna amp.
INSTALLATION
Install in the reverse order of removal.23 (L/B) – Ground : Battery voltage
PIIA6150E
PIIA6064E

PRECAUTIONS
BR-3
C
D
E
G
H
I
J
K
L
MA
B
BR

PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BFS000BB
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemBFS000BC

Clean dust on front brake and rear brake with a vacuum dust collector. Do not blow with compressed air.

Recommended fluid is brake fluid “DOT 3 or DOT 4”. Refer to MA-14, "Fluids and Lubricants" .

Do not reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is splashed
on painted surfaces of body, immediately wipe it off and them wash it away with water immediately.

To clean or wash all parts of master cylinder, disc brake caliper, use clean brake fluid.

Do not use mineral oils such as gasoline or kerosene. They will ruin rubber parts of the hydraulic system.

Use a flare nut torque wrench when installing brake tube.

When installing brake tube, be sure to check torque.

Before working, turn ignition switch OFF and disconnect electri-
cal connector of ABS actuator and electric unit (control unit) or
battery cables.

Burnish the brake contact surfaces after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low
mileage. Refer to BR-32, "
BRAKE BURNISHING PROCE-
DURE" (Front disc brake), BR-39, "BRAKE BURNISHING
PROCEDURE" (Rear disc brake).
WARNING:

Clean brake pads and shoes with a waste cloth, then wipe with a dust collector.
SBR820BA

BRAKE FLUID
BR-9
C
D
E
G
H
I
J
K
L
MA
B
BR

BRAKE FLUIDPFP:KN100
Checking Brake Fluid LevelBFS000BI

Make sure that a brake fluid level in reservoir tank is within the
standard (between MAX and MIN lines).

Visually check around reservoir tank for fluid leakage.

If fluid level is excessively low, check brake system for leakage.

Release parking brake pedal and see if brake warning lamp
goes off. If not, check brake system for fluid leakage.
Drain and RefillBFS000BJ
CAUTION:

Refill with new brake fluid “DOT 3 or DOT 4”.

Do not reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas; it way cause paint damage. If brake fluid is
splashed on painted surfaces of the body, immediately wipe off them and wash it away with water
immediately.

Before working, turn ignition switch OFF and disconnect electrical connector of ABS actuator and
electric unit (control unit) or battery cables.
1. Connect a vinyl tube to bleed valve.
2. Depress brake pedal, loosen bleed valve, and gradually remove
brake fluid.
3. Clean inside of reservoir tank, and refill with new brake fluid.
4. Rest foot on brake pedal. Loosen bleed valve. Slowly depress
brake pedal until it stops. Tighten bleed valve. Release brake
pedal. Repeat this process a few time, them pause to and new
brake fluid to master cylinder. Continue until new brake fluid
flows out.
5. Bleed air. Refer to BR-10, "
Bleeding Brake System" .
SFIA2632E
BRA0007D
PFIA0403J

BR-10
BRAKE FLUID

Bleeding Brake SystemBFS000BK
CAUTION:

Carefully monitor brake fluid level in reservoir tank during
bleeding operation.

Refill with new brake fluid “DOT 3 or DOT 4”. Make sure it is
at least half way at all times while bleeding air out of sys-
tem.

Place a container under master cylinder not to spill brake
fluid.

Turn ignition switch to the OFF and disconnect connector
for ABS actuator and electric unit (control unit) or battery
cable from negative terminal before working.
1. Connect a vinyl tube to rear right brake caliper bleed valve.
2. Fully depress brake pedal 4 or 5 times.
3. With brake pedal depressed, loosen bleed valve to bleed air in
brake line, and then tighten it immediately.
4. Repeat steps 2 and 3 until all of the air is out of the brake line.
5. Tighten bleed valve to the specified torque. Refer to front disc
brake: BR-26, "
Components" , rear disc brake: BR-33, "Compo-
nents" .
6. From step 1 to 5 above, with master cylinder reservoir tank filled
at least half way, bleed air from brake hydraulic line bleed valves
in the following order:
Rear right brake→Front left brake→Rear left brake→Front right brake
PFIA0403J
BRA0007D

BRC-1
BRAKE CONTROL SYSTEM
F BRAKES
CONTENTS
C
D
E
G
H
I
J
K
L
M
SECTION BRC
A
B
BRC

BRAKE CONTROL SYSTEM
ABS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Brake System .................................. 3
Precautions for Brake Control .................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
SYSTEM DESCRIPTION ............................................ 5
System Diagram ....................................................... 5
Functions .................................................................. 5
ABS ....................................................................... 5
EBD ....................................................................... 6
Fail-Safe Function .................................................... 6
ABS, EBD SYSTEM .............................................. 6
Hydraulic Circuit Diagram ........................................ 6
CAN Communication ................................................ 7
SYSTEM DESCRIPTION ...................................... 7
TROUBLE DIAGNOSIS .............................................. 8
How to Perform Trouble Diagnosis For Quick and
Accurate Repair ....................................................... 8
INTRODUCTION ................................................... 8
DIAGNOSIS FLOW CHART ................................. 9
ASKING COMPLAINTS ...................................... 10
EXAMPLE OF DIAGNOSIS SHEET ................... 10
Component Parts Location ...................................... 11
Schematic .............................................................. 12
Wiring Diagram — ABS — ..................................... 13
Control Unit Input/Output Signal Specifications ..... 16
REFERENCE VALUE FROM CONSULT-II ......... 16
CONSULT-II Functions (ABS) ................................ 17
CONSULT-II MAIN FUNCTION ........................... 17
CONSULT-II SETTING PROCEDURE ................ 17
Self-Diagnosis ........................................................ 17
DESCRIPTION .................................................... 17
OPERATION PROCEDURE ............................... 17
ERASE MEMORY ............................................... 17
DISPLAY ITEM LIST ........................................... 18Data Monitor ........................................................... 19
OPERATION PROCEDURE ................................ 19
DISPLAY ITEM LIST ........................................... 19
Active Test .............................................................. 20
OPERATION PROCEDURE ................................ 20
TEST ITEM .......................................................... 21
For Fast and Accurate Diagnosis ........................... 22
PRECAUTIONS FOR DIAGNOSIS ..................... 22
Basic Inspection ..................................................... 22
BRAKE FLUID LEVEL, LEAKAGE AND BRAKE
PAD ..................................................................... 22
POWER SUPPLY CIRCUIT TERMINAL LOOSE-
NESS AND BATTERY ......................................... 22
INSPECTION OF ABS WARNING LAMP AND
BRAKE WARNING LAMP ................................... 23
TROUBLE DIAGNOSIS FOR SYSTEM .................... 24
Wheel Sensor System ............................................ 24
ABS Actuator and Electric Unit (Control Unit) 1 ..... 26
ABS Actuator and Electric Unit (Control Unit) Power
Supply and Ground Circuit ..................................... 26
ABS Actuator Relay or ABS Motor Relay Power Sys-
tem .......................................................................... 28
CAN Communication System ................................. 29
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 30
Excessive ABS Function Operation Frequency ...... 30
Unexpected Pedal Action ....................................... 30
Longer Stopping Distance ...................................... 31
ABS Function Does Not Operate ............................ 31
Pedal Vibration and ABS Operation Sound Occurs ... 31
WHEEL SENSORS ................................................... 33
Removal and Installation ........................................ 33
COMPONENTS ................................................... 33
REMOVAL ........................................................... 33
INSTALLATION ................................................... 33
SENSOR ROTOR ..................................................... 34
Removal and Installation ........................................ 34
FRONT ................................................................ 34
REAR .................................................................. 34

BRC-2 ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) ... 35
Removal and Installation ........................................ 35
COMPONENTS ................................................... 35
REMOVAL ........................................................... 36
INSTALLATION .................................................... 36
VDC/TCS/ABS
PRECAUTIONS ......................................................... 37
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................. 37
Precautions for Brake System ................................ 37
Precautions for Brake Control ................................ 37
PREPARATION ......................................................... 39
Special Service Tools ............................................. 39
ON-VEHICLE SERVICE ............................................ 40
Adjustment of Steering Angle Sensor Neutral Posi-
tion .......................................................................... 40
OPERATION PROCEDURE ................................ 40
SYSTEM DESCRIPTION .......................................... 41
System Diagram ..................................................... 41
Functions ................................................................ 41
VDC ..................................................................... 41
TCS ..................................................................... 41
ABS ..................................................................... 42
EBD ..................................................................... 42
Fail-Safe Function .................................................. 42
VDC/TCS SYSTEM ............................................. 42
ABS, EBD SYSTEM ............................................ 42
Hydraulic Circuit Diagram ....................................... 43
CAN Communication .............................................. 43
SYSTEM DESCRIPTION .................................... 43
TROUBLE DIAGNOSIS ............................................ 44
How to Perform Trouble Diagnosis Quick and Accu-
rate Repair .............................................................. 44
INTRODUCTION ................................................. 44
DIAGNOSIS FLOW CHART ................................ 45
ASKING COMPLAINTS ....................................... 46
EXAMPLE OF DIAGNOSIS SHEET .................... 46
Component Parts Location ..................................... 47
Schematic ............................................................... 48
Wiring Diagram — VDC — ..................................... 49
Control Unit Input/Output Signal Specifications ...... 55
REFERENCE VALUE FROM CONSULT-II ......... 55
CONSULT-II Functions ........................................... 57
CONSULT-II MAIN FUNCTION ........................... 57
CONSULT-II SETTING PROCEDURE ................ 57
Self-Diagnosis ........................................................ 58
DESCRIPTION .................................................... 58
OPERATION PROCEDURE ................................ 58
ERASE MEMORY ............................................... 58
DISPLAY ITEM LIST ........................................... 59
Data Monitor ........................................................... 61
OPERATION PROCEDURE ................................ 61
DISPLAY ITEM LIST ........................................... 61
Active Test .............................................................. 63
OPERATION PROCEDURE ................................ 63TEST ITEM .......................................................... 64
For Fast and Accurate Diagnosis ............................ 65
PRECAUTIONS FOR DIAGNOSIS ..................... 65
Basic Inspection ...................................................... 66
BRAKE FLUID LEVEL, LEAKAGE AND BRAKE
PAD ...................................................................... 66
POWER SUPPLY CIRCUIT TERMINAL LOOSE-
NESS AND BATTERY ......................................... 66
INSPECTION OF ABS WARNING LAMP, BRAKE
WARNING LAMP, VDC OFF INDICATOR LAMP,
AND SLIP INDICATOR LAMP ............................. 66
TROUBLE DIAGNOSIS FOR SYSTEM .................... 68
Wheel Sensor System ............................................ 68
Engine System ........................................................ 70
ABS Actuator and Electric Unit (Control Unit) 1 ...... 70
Steering Angle Sensor System ............................... 71
Yaw Rate/Side/Decel G Sensor System ................. 72
Pump Motor, Motor Relay System .......................... 74
Park/Neutral Position (PNP) Switch Circuit ............. 75
Solenoid and VDC Change-Over Valve, Actuator
Relay System .......................................................... 76
Stop Lamp Switch System ...................................... 77
ABS Actuator and Electric Unit (Control Unit) Power
Supply and Ground System .................................... 78
Brake Fluid Level Switch System ............................ 80
CAN Communication System ................................. 81
Component Parts Inspection ................................... 81
VDC OFF SWITCH .............................................. 81
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 82
Excessive ABS Function Operation Frequently ...... 82
Unexpected Pedal Reaction ................................... 83
Longer Stopping Distance ....................................... 83
ABS Function Does Not Operate ............................ 84
Pedal Vibration and ABS Operation Sound Occurs ... 84
Vehicle Jerks During VDC/TCS/ABS Control .......... 85
WHEEL SENSORS ................................................... 86
Removal and Installation ......................................... 86
COMPONENTS ................................................... 86
REMOVAL ............................................................ 86
INSTALLATION .................................................... 86
SENSOR ROTOR ...................................................... 87
Removal and Installation ......................................... 87
FRONT ................................................................. 87
REAR ................................................................... 87
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) ... 88
Removal and Installation ......................................... 88
COMPONENTS ................................................... 88
REMOVAL ............................................................ 89
INSTALLATION .................................................... 89
G SENSOR ................................................................ 90
Removal and Installation ......................................... 90
REMOVAL ............................................................ 90
INSTALLATION .................................................... 90
STEERING ANGLE SENSOR ................................... 91
Removal and Installation ......................................... 91
REMOVAL ............................................................ 91
INSTALLATION .................................................... 91

PRECAUTIONS
BRC-3
[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

[ABS]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BFS000CK
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemBFS000CL

Recommended fluid is brake fluid “DOT 3” or “DOT 4”. Refer to MA-14, "RECOMMENDED FLUIDS AND
LUBRICANTS" .

Never reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas.

To clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.

Never use mineral oils such as gasoline or kerosene. They will
ruin rubber parts of the hydraulic system.

Using a flare nut wrench when removing flare nuts, and use a
flare nut torque wrench when tighten brake tube flare nuts.

When installing brake tubes, be sure to check torque.

Before working, turn ignition switch OFF and disconnect electri-
cal connector of ABS actuator and electric unit (control unit) or
battery negative terminal.
WARNING:
Clean brake pads and shoes with a waste cloth, then wipe with
a dust collector.
Precautions for Brake ControlBFS000CM

During ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating noise may
be heard from engine room. This is a normal condition of operation check.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.

When an error is indicated by ABS or another warning lamp, collect all necessary information from cus-
tomer (what symptoms are present under what conditions) and check for simple causes before starting
diagnostic servicing. Besides electrical system inspection, check brake booster operation, brake fluid
level, and fluid leaks.

If tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.

If there is a radio, antenna, or antenna lead-in wire (including wiring) near control module, ABS function
may have a malfunction or error.

If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits, and improper wiring.
SBR820BA

BRC-16
[ABS]
TROUBLE DIAGNOSIS

Control Unit Input/Output Signal SpecificationsBFS000CY
REFERENCE VALUE FROM CONSULT-II
CAUTION:
The monitor displays the control unit calculation data. The normal values will be displayed even that in
the event the output circuit (harness) is open or shorted.
Note 1: Confirm tire pressure is the standard value.
Note 2: Brake warning lamp can be used for EBD warning lamp.
Note 3: ON/OFF timing of ABS warning lamp
ON: For a while after ignition switch is turned ON, or when a malfunction is detected.
OFF: In a while after the warning lamp is ON (when the system is in normal operation). Monitor item Display itemDATA MONITOR
ConditionReference values for
normal operation
WHEEL SENSORVehicle speed calculated using sig-
nals from all four wheel sensorsVehicle stopped 0 [km/h (MPH)]
Vehicle running (Note 1)Almost in accordance
with speedometer dis-
play (within ± 10 %)
IN ABS S/V
OUT ABS S/VOperation condition of all solenoid
valvesWhen actuator (solenoid) operates or
during fail-safeON
When actuator relay operates and the
actuator (solenoid) does not operateOFF
EBD WARN LAMP
(Note 2)Brake warning lamp ON/OFF condi-
tionWhen brake warning lamp is ON ON
When brake warning lamp is OFF OFF
STOP LAMP SW Brake pedal operation conditionBrake pedal depressed ON
Brake pedal not depressed OFF
MOTOR RELAYMotor and motor relay operation con-
ditionWhen motor relay and motor are
operatingON
When motor relay and motor are not
operatingOFF
ACTUATOR RLY Actuator relay operation conditionActuator relay activated ON
Actuator relay not activated OFF
ABS WARN LAMPABS warning lamp ON/OFF condition
(Note 3)When ABS warning lamp is ON ON
When ABS warning lamp is OFF OFF
BATTERY VOLTBattery voltage supplied to ABS actu-
ator and electric unit (control unit)Ignition switch ON 10−16 V
EBD SIGNAL EBD operation signalEBD activated ON
EBD not activated OFF
ABS SIGNAL ABS operation signalABS activated ON
ABS not activated OFF
ABS FAIL SIG
Fail-safe signal conditionIn ABS fail-safe
OFF
EBD FAIL SIG In EBD fail-safe

BRC-18
[ABS]
TROUBLE DIAGNOSIS

DISPLAY ITEM LIST
Diagnostic item Diagnostic item is detected when... Reference
RR RH SENSOR−1
[C1101]When the circuit in the rear right wheel sensor is open.
BRC-24, "
Wheel Sensor
System"
(Note 1) RR LH SENSOR−1
[C1102]When the circuit in the rear left wheel sensor is open.
FR RH SENSOR−1
[C1103]When the circuit in the front right wheel sensor is open.
FR LH SENSOR−1
[C1104]When the circuit in the front left wheel sensor is open.
RR RH SENSOR−2
[C1105]When the circuit in the rear right wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
RR LH SENSOR−2
[C1106]When the circuit in the rear left wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
FR RH SENSOR−2
[C1107]When the circuit in the front right wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
FR LH SENSOR−2
[C1108]When the circuit in the front left wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
BATTERY VOLTAGE
[ABNORMAL]
[C1109]Battery voltage of the control unit is too low.BRC-26, "
ABS Actuator
and Electric Unit (Control
Unit) Power Supply and
Ground Circuit"
CONTROLLER FAILURE
[ C 111 0 ]When there is an internal malfunction in the control unit.BRC-26, "ABS Actuator
and Electric Unit (Control
Unit) 1"
FR LH IN ABS SOL
[C1120]This is displayed when the control unit detects a malfunction in the
front left wheel inlet solenoid circuit.
BRC-28, "
ABS Actuator
Relay or ABS Motor
Relay Power System"
FR LH OUT ABS SOL
[C1121]This is displayed when the control unit detects a malfunction in the
front left wheel outlet solenoid circuit.
FR RH IN ABS SOL
[C1122]This is displayed when the control unit detects a malfunction in the
front right wheel inlet solenoid circuit.
FR RH OUT ABS SOL
[C1123]This is displayed when the control unit detects a malfunction in the
front right wheel outlet solenoid circuit.
RR LH IN ABS SOL
[C1124]This is displayed when the control unit detects a malfunction in the
rear left wheel inlet solenoid circuit.
RR LH OUT ABS SOL
[C1125]This is displayed when the control unit detects a malfunction in the
rear left wheel outlet solenoid circuit.
RR RH IN ABS SOL
[C1126]This is displayed when the control unit detects a malfunction in the
rear right wheel inlet solenoid circuit.
RR RH OUT ABS SOL
[C1127]This is displayed when the control unit detects a malfunction in the
rear right wheel outlet solenoid circuit.
PUMP MOTOR
[ C 1111 ]This is displayed when the control unit detects a malfunction in the
motor or motor relay.
ACTUATOR RLY
[C1140]This is displayed when the control unit detects a malfunction in
actuator relay circuit.
CAN COMM CIRCUIT
[U1000]When there is a malfunction in the CAN communication system.BRC-29, "
CAN Communi-
cation System"
(Note 2)

BRC-20
[ABS]
TROUBLE DIAGNOSIS

×: Applicable
−: Not applicable
Note: Brake warning lamp can be used for EBD warning lamp.
Active TestBFS000D2
CAUTION:

Do not perform ACTIVE TEST while driving vehicle.

Make sure to completely bleed air from brake system.

Active test cannot be performed when ABS warning lamp is turned on.

ABS and brake warning lamps turn on during active test.
OPERATION PROCEDURE
1. Perform “CONSULT-II Starting procedure”. Refer to GI-34, "CONSULT-II Start Procedure" .
2. Touch “ACTIVE TEST” in order on the CONSULT-II screen.
3. The “ SELECT TEST ITEM” screen is displayed.
4. Touch necessary test item.
5. Touch “START” with “MAIN SIGNALS” line inverted.
6. ACTIVE TEST screen will be displayed, so perform the following test.

Solenoid valve

ABS motor
NOTE:

When active test is performed while depressing brake pedal, the pedal height will change, but this is
normal.

Approximately 10 seconds after operation has begun, “TEST STOP” will be displayed.

To perform a retest after “TEST STOP” is displayed, touch “BACK” and perform test from step 3.
BATTERY VOLT
(V)×××Condition of voltage supplied to ABS actuator
and electric unit (control unit) is displayed.
EBD SIGNAL
(ON/OFF)——×Condition of EBD operation (ON/OFF) is dis-
played.
ABS SIGNAL
(ON/OFF)——×Condition of ABS operation (ON/OFF) is dis-
played.
EBD FAIL SIG
(ON/OFF)——×Condition of EBD fail-safe signal (ON/OFF) is
displayed.
ABS FAIL SIG
(ON/OFF)——×Condition of ABS fail-safe signal (ON/OFF) is
displayed. Item (Unit)Monitor item selection
Remarks
ECU INPUT
SIGNALSMAIN SIGNALSSELECTION
FROM MENU
SFIA2085E