Back lamp NISSAN TEANA 2003 Owner's Manual

ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-379
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EC

2. Make sure that monitoring sensor has changed by MI blinking as follows.
How to Erase Diagnostic Test Mode II (Self-diagnostic Results)
1. Set ECM in Diagnostic Test Mode II (Self-diagnostic results). Refer to EC-378, "How to Set Diagnostic
Test Mode II (Self-diagnostic Results)" .
2. Fully depress the accelerator pedal and keep it for more than 10 seconds.
The emission-related diagnostic information has been erased from the backup memory in the ECM.
3. Fully release the accelerator pedal, and confirm the DTC 0000 is displayed.
DIAGNOSTIC TEST MODE I — BULB CHECK
In this mode, the MI on the instrument panel should stay ON. If it remains OFF, check the bulb. Refer to DI-35,
"WARNING LAMPS" or see EC-763 .
DIAGNOSTIC TEST MODE I — MALFUNCTION WARNING

These DTC numbers are clarified in Diagnostic Test Mode II (SELF-DIAGNOSTIC RESULTS)
DIAGNOSTIC TEST MODE II — SELF-DIAGNOSTIC RESULTS
In this mode, the DTC and 1st trip DTC are indicated by the number of blinks of the MI as shown below.
The DTC and 1st trip DTC are displayed at the same time. If the MI does not illuminate in diagnostic test mode
I (Malfunction warning), all displayed items are 1st trip DTCs. If only one code is displayed when the MI illumi-
nates in diagnostic test mode II (SELF-DIAGNOSTIC RESULTS), it is a DTC; if two or more codes are dis-
played, they may be either DTCs or 1st trip DTCs. DTC No. is same as that of 1st trip DTC. These unidentified
codes can be identified by using the CONSULT-II. A DTC will be used as an example for how to read a code.
PBIB0093E
MI Condition
ON When the malfunction is detected
OFF No malfunction
PBIA3905E

EC-428
[VQ]
TROUBLE DIAGNOSIS

DATA MONITOR MODE
Monitored Item
×: Applicable
Monitored item
[Unit]ECM
INPUT
SIGNALSMAIN
SIGNALSDescription Remarks
ENG SPEED [rpm]××

Indicates the engine speed computed from
the signal of the crankshaft position sensor
(POS) and camshaft position sensor
(PHASE).
Accuracy becomes poor if engine
speed drops below the idle rpm.

If the signal is interrupted while the
engine is running, an abnormal value
may be indicated.
MAS A/F SE-B1 [V]××

The signal voltage of the mass air flow sen-
sor is displayed.
When the engine is stopped, a cer-
tain value is indicated.
B/FUEL SCHDL
[msec]×

Base fuel schedule indicates the fuel injec-
tion pulse width programmed into ECM,
prior to any learned on board correction.
A/F ALPHA-B1 [%]×

The mean value of the air-fuel ratio feed-
back correction factor per cycle is indi-
cated.
When the engine is stopped, a cer-
tain value is indicated.

This data also includes the data for
the air-fuel ratio learning control. A/F ALPHA-B2 [%]×
COOLAN TEMP/S
[°C] or [°F]××

The engine coolant temperature (deter-
mined by the signal voltage of the engine
coolant temperature sensor) is displayed.

When the engine coolant tempera-
ture sensor is open or short-cir-
cuited, ECM enters fail-safe mode.
The engine coolant temperature
determined by the ECM is displayed.
HO2S1 (B1) [V]××

The signal voltage of the heated oxygen
sensor 1 is displayed.
HO2S1 (B2) [V]×
HO2S2 (B1) [V]×

The signal voltage of the heated oxygen
sensor 2 is displayed.
HO2S2 (B2) [V]×
HO2S1 MNTR (B1)
[RICH/LEAN]××

Display of heated oxygen sensor 1 signal
during air-fuel ratio feedback control:
RICH: means the mixture became “rich”,
and control is being affected toward a
leaner mixture.
LEAN: means the mixture became “lean”,
and control is being affected toward a rich
mixture.
After turning ON the ignition switch,
“RICH” is displayed until air-fuel mix-
ture ratio feedback control begins.

When the air-fuel ratio feedback is
clamped, the value just before the
clamping is displayed continuously. HO2S1 MNTR (B2)
[RICH/LEAN]×
HO2S2 MNTR (B1)
[RICH/LEAN]×

Display of heated oxygen sensor 2 signal:
RICH: means the amount of oxygen after
three way catalyst is relatively small.
LEAN: means the amount of oxygen after
three way catalyst is relatively large.

When the engine is stopped, a cer-
tain value is indicated.
HO2S2 MNTR (B2)
[RICH/LEAN]×
VHCL SPEED SE
[km/h] or [mph]××

The vehicle speed computed from the vehi-
cle speed signal sent from combination
meter is displayed.
BATTERY VOLT
[V]××

The power supply voltage of ECM is dis-
played.
ACCEL SEN 1 [V]××

The accelerator pedal position sensor sig-
nal voltage is displayed.
ACCEL SEN 2 signal is converted by
ECM internally. Thus, it differs from
ECM terminal voltage signal. ACCEL SEN 2 [V]×
THRTL SEN 1 [V]××

The throttle position sensor signal voltage
is displayed.
THRTL SEN 2 signal is converted by
ECM internally. Thus, it differs from
ECM terminal voltage signal. THRTL SEN 2 [V]×
INT/A TEMP SE
[°C] or [°F]××

The intake air temperature (determined by
the signal voltage of the intake air tempera-
ture sensor) is indicated.

EI-24
CENTER MUD GUARD

CENTER MUD GUARDPFP:76850
Removal and InstallationBIS0011J
REMOVAL
1. Remove screws of mudguard front/rear side.
2. Remove bolts of mudguad lower side.
3. Fully open front door and rear door.
4. Remove clips from back of mudguard using clip clamp remover.
5. Remove center mudguard from body side.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing center mudguard, make sure that clips are securely fitted in panel holes on body, and
then press them in.
PIIA6258E
1. Screw 2. Bolt 3. Center mudguard
4. Clip (C101)

EI-32
DOOR OUTSIDE LOWER MOLDING

DOOR OUTSIDE LOWER MOLDINGPFP:82877
Removal and InstallationBIS0011P
FRONT AND REAR DOOR OUTSIDE LOWER MOLDING
Removal
1. Half-open front door and rear door.
2. Remove nuts from back of door panel.
3. Disengage mounting clips from molding rear end to front end using a clip clamp remover.
4. Remove door outside lower molding from body side after disengaging.
5. Slide molding toward rear of vehicle, and then remove front end clip.
CAUTION:
After removal, visually inspect molding, and if it is deformed, replace it with new molding.
Installation
Install in the reverse order of removal.
CAUTION:
When installing, confirm clips are accurately aligned with the holes on body side panel, then press in.
PIIA6257E
1. Clip (C101) 2. Door lower molding (front) 3. Stud bolt
4. Door lower molding (rear) 5. Nut

EI-36
DOOR FINISHER

FRONT AND REAR DOOR FINISHER
Removal
1. Fully open door window.
2. Remove inside handle escutcheon cap.
3. Remove inside handle escutcheon screw.
4. Insert a remover tool A into power window switch finisher (front)
(1), lift up front end and disengage metal clip. Pull out finisher
toward front of vehicle.
CAUTION:
Lift up rear end of power window switch finisher (rear) and
disengage metal clips, and then pull out finisher toward
rear of vehicle.
5. Disconnect power window switch harness connector after pulling out, and then remove power window
switch finisher.
6. Remove power window switch screws.
7. Insert a clip clamp remover into clips on back of door trim, and
disengage clips.
CAUTION:
Insert a clip clamp remover into the part shown by the
arrow (between the clips and the body side panel). Remove
door trim.
8. Disconnect harness connector for trunk lid opener after disengaging.
9. Disconnect harness connector for seat memory switch (1) and
indirect lighting (2).
10. Disconnect harness connector for step lamp.
11. Pull up door trim and pull out toward vehicle inside, and then dis-
connect inside handle cable (3) and lock knob cable (2) from
inside handle (1).
PIIB8685E
SIIA0810E
PIIB8687E
PIIB8686E

BODY SIDE TRIM
EI-41
C
D
E
F
G
H
J
K
L
MA
B
EI

2. Remove kicking plate inner mounting clips using a clip clamp
remover, and then remove kicking plate inner.
Installation
Install in the reverse order of removal.
REAR BODY SIDE WELT
Removal
1. Remove center pillar lower garnish.
2. Remove rear seat cushion. Refer to SE-112, "
REAR SEAT" .
3. Remove rear kicking plate inner.
4. Remove rear body side welt.
Installation
Install in the reverse order of removal.
REAR SEATBACK FINISHER
Removal
1. Remove rear seat cushion and rear seatback. Refer to SE-112,
"REAR SEAT" .
2. Remove rear seat belt floor anchor bolt. Refer to SB-5,
"Removal and Installation of Rear Seat Belt" .
3. Remove rear kicking plate inner.
4. Remove rear seatback finisher.
Installation
Install in the reverse order of removal.
NOTE:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
REAR PILLAR FINISHER
Removal
1. Remove rear seat cushion and rear seatback. Refer to SE-112,
"REAR SEAT" .
2. Remove rear seat belt floor anchor bolt. Refer to SB-5,
"Removal and Installation of Rear Seat Belt" .
3. Remove rear kicking plate inner.
4. Remove rear seatback finisher.
5. Remove pillar finisher mounting clips using a screwdriver, and
then remove pillar finisher.
PIIA7074E
PIIA7075E
PIIA7076E

EI-44
REAR PARCEL SHELF FINISHER

REMOVAL
1. Remove rear seatback and rear seat cushion. Refer to SE-112, "REAR SEAT" .
2. Remove rear seat belt floor anchor bolt and rear seat belt shoulder anchor bolt. Refer to SB-5, "
Removal
and Installation of Rear Seat Belt" .
3. Disengage child anchor cover front pawls, and then pull out child
anchor cover (LH/RH center) toward front of vehicle.(Models
with rear window sunshade)
4. Remove rear kicking plate inner, rear seatback finisher, rear pillar finisher. Refer to EI-38, "
BODY SIDE
TRIM" .
5. Disconnect high-mounted stop lamp harness connector from
trunk room side. (Models without rear window sunshade)
6. Disconnect high-mounted stop lamp harness connector from
front side of rear parcel shelf finisher. (Models with rear window
sunshade)
7. Remove rear parcel shelf finisher mounting clip using a clip clamp remover.
8. Remove rear parcel shelf finisher while disengaging dual-lock fastener on back of rear parcel shelf fin-
isher. (Models with rear window sunshade)
9. Remove the following parts after removing rear parcel shelf finisher.

Rear speaker grille (for woofer)

High-mounted stop lamp
INSTALLATION
Install in the reverse order of removal.
7. Screw 8.Rear parcel shelf finisher (with sun-
shade)9. Child anchor cover (LH/RH center)
10. Rear window sunshade 11. Bolt 12. Locating pin
PIIA9530E
PIIA9531E
PIIA9535E

HEADLINING
EI-55
C
D
E
F
G
H
J
K
L
MA
B
EI

REMOVAL
1. Remove front seat belt floor anchor bolt and rear seat belt floor ancher bolt. Refer to SB-3, "SEAT BELTS"
and SB-5, "Removal and Installation of Rear Seat Belt" .
2. Remove rear seat. Refer to SE-112, "
REAR SEAT" .
3. Remove front pillar garnish (LH/RH). Refer to EI-38, "
BODY SIDE TRIM" .
4. Remove roof harness securing clip using a clip clamp remover
after removing, and then disconnect roof harness connector.
5. Remove front kicking plate inner, center pillar lower garnish, center pillar upper garnish, front body side
welt, rear kicking plate inner, rear seatback finisher, rear pillar finisher, and rear body side welt. Refer to
EI-38, "
BODY SIDE TRIM" .
6. Remove mounting clips of front assist grip (RH) and rear assist
grip (LH/RH).
7. Remove sun-visor (LH/RH) mounting screws.
NOTE:
Disconnect vanity mirror illumination harness connector when removing sun-visor.
1. Clip (C101) 2. Headlining (standard model) 3. Rear assist grip (RH)
4. Personal lamp (RH) 5. Roof harness securing clip 6. Roof harness connector
7. Sun-visor (RH) 8. Sun-visor holder (RH) 9. Screw
10. Cap (RH) 11. Spot lamp (map lamp) 12. Sun-visor holder (LH)
13. Cap (LH) 14.Vanity mirror illumination harness con-
nector15. Sun-visor (LH)
16.Spot lamp(map lamp) harness
connector (standardmodel)17. Metal clip 18. Dual lock fastener (with sunroof model)
19.Harness connector for hands-
free phone microphone
(model with car wings unit)20.Roof harness securing tape (standard
model)21. Front assist grip (RH)
22. Personal lamp (LH) 23. Rear assist grip (LH) 24. Clip holder
25.Headlining (model with sun-
roof)26.Sunroof motor harness connector
(model with sunroof)27. Front roof finisher (model with sunroof)
28.Roof hook (model with sun-
roof)
PIIA7118E
PIIA6267E

EI-56
HEADLINING

8. Remove sun-visor holder (LH/RH).
NOTE:
Insert a screwdriver into the cutout and rotate 90 degrees to
remove.
9. Remove clips from back of front roof finisher, and then pull out
front roof finisher toward front of vehicle to remove it. (with sun-
roof model)
10. Pull out sunroof motor harness connector from front roof finisher
mounting hole to disconnect. (with sunroof model)
11. Pull out spot lamp (map lamp) toward lower side of vehicle and disconnect harness connector.
12. Disconnect harness connector for hands-free phone microphone. (Only for models with Car wings unit)
13. Pull spot lamp holder assembly toward vehicle lower, and disen-
gage dual-lock fastener and metal clips.
SIIA0224J
PIIA9621E
PIIA9622E
PIIA6272E

IDX-2
ALPHABETICAL INDEX
Numerics
3rd position switch ............................. AT-161
, AT-210
A
A/C air flow ...................................................... ATC-31
A/C component layout ..................................... ATC-20
A/C compressor clutch removal and installation ...........
ATC-136
A/C compressor mounting ............................. ATC-134
A/C compressor precaution ............................. ATC-11
A/C compressor special service tool ................ ATC-15
A/C control operation (auto A/C) ...................... ATC-29
A/C diagnostic work flow (auto A/C) ................ ATC-94
A/C evaporator ............................................... ATC-144
A/C HFC134a (R134a) system precaution ........ ATC-5
A/C HFC134a (R134a) system service procedure .......
ATC-131
A/C HFC134a (R134a) system service tools ... ATC-16
A/C HFC134a system service equipment precaution ...
ATC-12
A/C lubricant (R134a) ...................................... ATC-21
A/C lubrication oil ........................................... ATC-150
A/C operational check ...................................... ATC-54
A/C self-diagnoses (auto A/C) .......... ATC-46, ATC-94
A/C service data specification ........................ ATC-150
A/C system description (auto A/C) ................... ATC-24
A/C, A - Wiring diagram ................................... ATC-39
A/T fluid checking .................................. AT-14, MA-35
A/T fluid replacement ............................. AT-15, MA-36
A/T IND - Wiring diagram .................................... DI-48
A/T shift control system ................................... AT-213
A/T shift lock system ........................................ AT-216
A/T shift lock system - Wiring diagram ............ AT-217
A/T trouble diagnoses ........................................ AT-34
Accelerator control system ............................... ACC-3
Accelerator pedal position (APP) sensor ........ EC-251,
EC-258
, EC-272, EC-631, EC-638, EC-652
Accelerator pedal released position learning .... EC-47,
EC-389
AFS ..................................................................... LT-75
AFS - Wiring diagram ......................................... LT-79
Air bag .............................................................. SRS-3
Air bag disposal .............................................. SRS-48
Air bag precautions ........................................... SRS-3
Air cleaner and air duct(QR20DE) .................... EM-17
Air cleaner and air duct(VQ23DE and VQ35DE) ..........
EM-131
Air cleaner filter replacement(QR20DE) ........... MA-20
Air cleaner filter replacement(VQ23DE and VQ35DE) .
MA-30
Air cleaner filter(QR20DE) ................................ EM-17
Air cleaner filter(VQ23DE and VQ35DE) ........ EM-132
Air conditioner cut control .................... EC-25, EC-362
Air flow meter - See Mass air flow sensor ...... EC-124,
EC-466
Air mix. door motor ......................... ATC-66, ATC-124
Ambient sensor ............................... ATC-96, ATC-109
Angular tightening application(QR20DE) ............ EM-6
Angular tightening application(VQ23DE and VQ35DE)
EM-120
Antenna ............................................................. AV-38
APPS1 - Wiring diagram ................... EC-253, EC-633
APPS2 - Wiring diagram ................... EC-260, EC-640
APPS3 - Wiring diagram ................... EC-274, EC-654
ASC/BS - Wiring diagram ................................ EC-605
ASC/SW - Wiring diagram ............................... EC-597
ASCBOF - Wiring diagram ............................... EC-661
ASCD ............................................................... EC-363
ASCD (automatic speed control device) ........... ACS-2
ASCD brake switch ........................... EC-602, EC-660
ASCD indicator lamp ....................................... EC-667
ASCD steering switch ...................................... EC-595
ASCIND - Wiring diagram ................................ EC-668
AT indicator lamp ................................................ DI-48
Audio ........................................................ AV-4, AV-18
AUDIO - Wiring diagram .......................... AV-7, AV-21
Auto air conditioner - Wiring diagram ............. ATC-39
Auto amp ...................................................... ATC-108
Auto anti-dazzling inside mirror ....................... GW-80
Automatic amplifier ........... ATC-44, ATC-56, ATC-108
AV communication line .......................... AV-49, AV-73
Axle ................................................................... MA-42
B
BA/FTS - Wiring diagram ................................. AT-111
BACK/L - Wiring diagram ................................. LT-193
Back-up lamp ................................................... LT-193
Basic inspection .................................. EC-40, EC-381
Battery ................................................................. SC-4
BCM (Body control module) .............................. BCS-3
Blower motor ................................... ATC-72, ATC-115
Blower unit .................................................... ATC-113
Boring/horning cylinder block(QR20DE) ......... EM-104
Boring/horning cylinder block(VQ23DE and VQ35DE) .
EM-250
Brake fluid level ................................................ MA-40
Brake hydraulic line ........................................... BR-11
Brake inspection ............................................... MA-41
Brake lines and cables inspection .................... MA-40
Brake pedal .......................................................... BR-6
Brake switch ......... EC-245, EC-602, EC-626, EC-660
BRK/SW - Wiring diagram ................ EC-247, EC-627
Bulb specifications ........................................... LT-261
Bumper, front ...................................................... EI-14
Bumper, rear ....................................................... EI-17
C
Camshaft inspection(QR20DE) ........................ EM-44
Camshaft inspection(VQ23DE and VQ35DE) EM-194
Camshaft position sensor (PHASE) .. EC-176, EC-524
Camshaft(QR20DE) .......................................... EM-41
Camshaft(VQ23DE and VQ35DE) .................. EM-192
CAN - Wiring diagram ......... EC-114, EC-459, AT-134,
CVT-54