SEC NISSAN TEANA 2014 Service Manual

TM-312
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10E]
P0712 TRANSMISSION FLUID
TEMPERATURE SENSOR A
P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC LogicINFOID:0000000009464266
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait for 10 seconds or more.
2. Check the first trip DTC.
Is
“P0712” detected?
YES >> Go to TM-312, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000009464267
1.CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace malfunctioning part.
2.CHECK CVT FLUID TE MPERATURE SENSOR
Check CVT fluid temperature sensor. Refer to TM-312, "Component Inspection"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Repair or replace malfunctioning parts.
Component InspectionINFOID:0000000009464268
1.CHECK CVT FLUID TE MPERATURE SENSOR
Check resistance between CVT unit connector terminals.
DTC CONSULT screen terms
(Trouble diagnosis content) DTC detection condition Possible causes
P0712 FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit Low) When all of the following conditions are satis-
fied and this state is maintained for 5 seconds:
• TCM power supply voltage : More than 11 V
• Fluid temperature sensor detection voltage:
0.15 V or less • Harness or connector
(CVT fluid temperature sensor circuit is
shorted to ground)
• CVT fluid temperature sensor
TCM —Continuity
Connector Terminal
F16 12 Ground Not existed
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-314
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10E]
P0713 TRANSMISSION FLUID
TEMPERATURE SENSOR A
P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC LogicINFOID:0000000009464269
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Maintain the following condition for 10 seconds or more.
3. Stop the vehicle.
4. Check the first trip DTC.
Is
“P0713” detected?
YES >> Go to TM-314, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000009464270
1.CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace malfunctioning parts.
2.CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 2)
1. Turn ignition switch ON.
2. Check voltage between TCM harness connector terminal and ground.
DTC CONSULT screen terms
(Trouble diagnosis content) DTC detection condition Possible causes
P0713 FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit High) When all of the following conditions are satis-
fied and this state is maintained for 5 seconds:
• TCM power supply voltage: More than 11 V
• Vehicle speed: More than 10 km/h (7 MPH)
• Fluid temperature sensor detection voltage: 2.48 V or more • Harness or connector
(CVT fluid temperature sensor circuit is
open or shorted to power supply)
• CVT fluid temperature sensor
Vehicle speed : 20 km/h (12 MPH) or more
TCM CVT unit Continuity
Connector Terminal Connector Terminal
F16 11
F46 16
Existed
12 17
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-316
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10E]
P0715 INPUT SPEED SENSOR A
P0715 INPUT SPEED SENSOR A
DTC LogicINFOID:0000000009464272
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following conditions for 10 seconds or more.
4. Stop the vehicle.
5. Check the first trip DTC.
Is
“P0715” detected?
DTC CONSULT screen terms
(Trouble diagnosis con-
tent) DTC detection condition
Possible causes
P0715 INPUT SPEED SEN-
SOR A
(Input/Turbine Speed
Sensor A Circuit) When 1 is satisfied and any of 2, 3 or 4 is satisfied:
1. When the following conditions are satisfied:
- TCM power supply voltage: More than 11 V
- After range change completion, it spends 2 sec- onds or more.
2. When all of the following conditions are satisfied
and this state is maintained for 5 seconds:
- Primary pulley speed: Less than 150 rpm
- Secondary pulley speed: 500 rpm or more
3. When all of the following conditions are satisfied and this state is maintained for 0.5 seconds:
- 10-msec-ago primary pulley speed: 1,000 rpm or
more
- Now primary pulley speed: 0 rpm
4. When all of the following conditions are satisfied
and this state is maintained for 5 seconds:
- Range: D or DS
- Engine speed: 450 rpm or more
- Input peed: 300 rpm or more
- Primary pulley speed: 300 rpm or more
- Secondary pulley seed: 300 rpm or more
- Differences between engine speed and primary
pulley speed: More than 1,000 rpm
- Differences between primary pulley speed and in- put speed speed: More than 1,000 rpm
- Differences between engine speed and input speed speed: 1,000 rpm or less
- Lock-up command is being given (except for slip
lock-up)
- DTC other than the applicable DTC is not detected. • Harness or connector
(Primary speed sensor circuit is
open or shorted)
• Primary speed sensor
Selector lever : “D” POSITION
Engine speed : 1,200 rpm or more
Vehicle speed : 40 km/h (25 MPH) or more
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

P0717 INPUT SPEED SENSOR ATM-319
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F10E]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P0717 INPUT SPEED SENSOR A
DTC LogicINFOID:0000000009464274
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROC EDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following conditions for 10 seconds or more.
DTC CONSULT screen terms
(Trouble diagnosis content) DTC detection condition Possible cause
P0717 INPUT SPEED SENSOR A
(Input/Turbine Speed Sensor
“A” Circuit No Signal) When 1 is satisfied and any of 2, 3 or 4 is satisfied:
1. When the following conditions are satisfied:
- TCM power supply voltage: More than 11 V
- After range change completion, it spends 2
seconds or more.
2. When all of the following conditions are satis- fied and this state is maintained for 5 sec-
onds:
- Primary pulley speed: 500 rpm or more
- Input speed: Less than 150 rpm
- Range: Other than P, N
- P0715 is not detected
3. When all of the following conditions are satis-
fied and this state is maintained for 0.5 sec-
onds:
- 10-msec-ago input speed: 1,000 rpm or more
- Now input speed: 0 rpm
4. When all of the following conditions are satis- fied and this state is maintained for 5 sec-
onds:
- Range: D or DS
- Engine speed: 450 rpm or more
- Input peed: 300 rpm or more
- Primary pulley speed: 300 rpm or more
- Secondary pulley seed: 300 rpm or more
- Differences between engine speed and pri-
mary pulley speed: 1,000 rpm or less
- Differences between primary pulley speed and input speed speed: More than 1,000 rpm
- Differences between engine speed and input speed speed: More than 1,000 rpm
- Lock-up command is being given (except for
slip lock-up)
- DTC other than the applicable DTC is not de- tected. • Harness or connectors
(Input speed sensor circuit is open
or shorted.)
• Input speed sensor
Selector lever : “D” position
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-322
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10E]
P0740 TORQUE CONVERTER
P0740 TORQUE CONVERTER
DTC LogicINFOID:0000000009464276
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PREPARATION BEFORE OPERATION
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “FLUID TEMP”.
4. Confirm that the CVT fluid temper ature is in the following range.
With GST
1. Start the engine.
2. Set the CVT fluid to 20 °C (68 °F) or more.
NOTE:
When the ambient temperature is 20 °C (68 °F), the CVT fluid usually increases to 50 to 80 °C (122 to
176 °F) with driving in an urban area for approximately 10 minutes.
Is the CVT fluid 20
°C (68°F) or more?
YES >> GO TO 3.
NO >> 1. Warm the transaxle. 2. GO TO 3.
3.CHECK DTC DETECTION
1. Drive the vehicle.
2. Maintain the following conditions for 10 seconds or more.
3. Stop the vehicle.
4. Check the first trip DTC.
Is
“P0740” detected?
YES >> Go to TM-323, "Diagnosis Procedure".
NO >> INSPECTION END
DTC CONSULT screen terms
(Trouble diagnosis content) DTC detection condition Possible causes
P0740 TORQUE CONVERTER
(Torque Converter Clutch Cir-
cuit/Open) When all of the following conditions are satis-
fied and this state is maintained for 5 seconds:
• TCM power supply voltage: More than 11 V
• P0743 is not detected.
• TCM judges that solenoid valve circuit is open. • Harness or connector
(Torque converter clutch solenoid valve
circuit is open or shorted to power sup-
ply)
• Torque converter clutch solenoid valve
FLUID TEMP : 20 °C (68 °F) or more
Selector lever : “D” position
Vehicle speed : 40 km/h (25 MPH) or more
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-324
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10E]
P0743 TORQUE CONVERTER
P0743 TORQUE CONVERTER
DTC LogicINFOID:0000000009464278
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PREPARATION BEFORE OPERATION
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “FLUID TEMP”.
4. Confirm that the CVT fluid temper ature is in the following range.
With GST
1. Start the engine.
2. Set the CVT fluid to 20 °C (68 °F) or more.
NOTE:
When the ambient temperature is 20 °C (68 °F), the CVT fluid usually increases to 50 to 80 °C (122 to
176 °F) with driving in an urban area for approximately 10 minutes.
Is the CVT fluid 20
°C (68°F) or more?
YES >> GO TO 3.
NO >> 1. Warm the transaxle. 2. GO TO 3.
3.CHECK DTC DETECTION
1. Drive the vehicle.
2. Maintain the following conditions for 10 seconds or more.
3. Stop the vehicle.
4. Check the first trip DTC.
Is
“P0743” detected?
YES >> Go to TM-325, "Diagnosis Procedure".
NO >> INSPECTION END
DTC CONSULT screen terms
(Trouble diagnosis content) DTC detection condition Possible causes
P0743 TORQUE CONVERTER
(Torque Converter Clutch Cir-
cuit Electrical) When all of the following conditions are satis-
fied and this state is maintained for 0.48 sec-
onds:
• TCM power supply voltage: More than 11 V
• TCM judges that solenoid valve circuit is shorted to ground. • Harness or connector
(Torque converter clutch solenoid valve
circuit is shorted to ground)
• Torque converter clutch solenoid valve
FLUID TEMP : 20 °C (68 °F) or more
Selector lever : “D” position
Vehicle speed : 40 km/h (25 MPH) or more
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-326
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10E]
P0744 TORQUE CONVERTER
P0744 TORQUE CONVERTER
DTC LogicINFOID:0000000009464280
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PREPARATION BEFORE OPERATION
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “FLUID TEMP”.
4. Confirm that the CVT fluid temper ature is in the following range.
With GST
1. Start the engine.
2. Set the CVT fluid to 20 °C (68 °F) or more.
NOTE:
When the ambient temperature is 20 °C (68 °F), the CVT fluid usually increases to 50 to 80 °C (122 to
176 °F) with driving in an urban area for approximately 10 minutes.
Is the CVT fluid 20
°C (68°F) or more?
YES >> GO TO 3.
NO >> 1. Warm the transaxle. 2. GO TO 3.
3.CHECK DTC DETECTION
1. Drive the vehicle.
2. Maintain the following conditions for 10 seconds or more.
3. Stop the vehicle.
4. Check the first trip DTC.
Is
“P0744” detected?
YES >> Go to TM-327, "Diagnosis Procedure".
DTCCONSULT screen terms
(Trouble diagnosis content) DTC detection condition Possible causes
P0744 TORQUE CONVERTER
(Torque converter clutch cir-
cuit intermittent) When all of the following conditions are satis-
fied and this state is maintained for 30 sec-
onds:
• TCM power supply voltage: More than 11 V
• P0717 is not detected.
• CAN communication is normal
• Torque converter slip speed: (40+vihicle
speed/2) rpm
• LU pressure: More than 0.2 MPa • Torque converter clutch solenoid valve
• Control valve assembly
• Torque converter
FLUID TEMP : 20 °C (68 °F) or more
Selector lever : “D” position
Accelerator pedal position : 0.5/8 or more
Vehicle speed : 40 km/h (25 MPH) or more
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-328
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10E]
P0746 PRESSURE CONTROL SOLENOID A
P0746 PRESSURE CONTROL SOLENOID A
DTC LogicINFOID:0000000009464282
DTC DETECTION LOGIC
NOTE:
DC stands for "DRIVING CYCLE" and indicates a seri es of driving cycle of "Ignition switch OFF → ON → driv-
ing → OFF".
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following conditions for 10 seconds or more.
4. Stop the vehicle.
5. Check the first trip DTC.
Is
“P0746”detected?
YES >> Go to TM-329, "Diagnosis Procedure".
DTCCONSULT screen terms
(Trouble diagnosis content) DTC detection condition Possible causes
P0746 PC SOLENOID A
(Pressure Contro l Solenoid A
Performance/Stuck Off) The detecting condition A or detection condi-
tion B is detected twice or more (1 second or
more later after detection of the first) in the
same DC under the following diagnosis condi-
tions:
• Diagnosis conditions
- Engine speed: More than 600 rpm
- Primary pulley speed: More than 450 rpm
- Idle is not being detected.
- Acceleration/deceleration speed: −0.49 m/
s
2 ( −0.05 G) or more
- The primary pulley speed experienced 300
rpm or more and the secondary pulley
speed experienced 250 rpm or more at least
once.
- Secondary pulley speed: More than 150
rpm
- TCM power supply voltage: More than 11 V
• Detection condition A
- Status with the shifting ratio of the primary pulley speed/secondary pulley ratio exceed-
ing 2.825 is 0.2 sec or more continuously.
• Detection condition B
- Status with the shifting ratio of the primary pulley speed/secondary pulley ratio exceed-
ing 3.625 is 0.1 sec or more continuously. • Line pressure solenoid valve
• Control valve assembly
Selector lever : “D” position
Accelerator pedal position : 0.5/8 or more
Vehicle speed : 40 km/h (25 MPH) or more
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-330
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10E]
P0776 PRESSURE CONTROL SOLENOID B
P0776 PRESSURE CONTROL SOLENOID B
DTC LogicINFOID:0000000009464284
DTC DETECTION LOGIC
DTCCONSULT screen terms
(Trouble diagnosis content) DTC detection condition Possible cause
P0776 PC SOLENOID B
(Pressure Control Solenoid
“B” Performance/Stuck Off) When any of 1 or 2 is satisfied and this state
is maintained for 10 seconds:
1. When all of the following conditions are satisfied:
- DTC other than the applicable DTC is not detected.
- Engine speed: More than 625 rpm
- Selector lever: Other than P/N position
- CVT fluid temperature: More than - 20°C (-4 °F)
- TCM power supply: More than 11 V
- The difference between instruction pressure of secondary pressure and
10-msec-ago instruction secondary
pressure is 0 MPa or more
- Instruction pressure of secondary
pressure: 0 MPa or more
- Instruction pressure of secondary pressure - secondary pressure: More
than 1.2 MPa
- When all of the following conditions are satisfied and this state is maintained
for 5.5 seconds:
• DTC other than the applicable DTC is not detected.
• CVT fluid temperature: More than -
20°C (-4 °F)
• Selector lever: Other than P/N position
• Secondary pressure - instruction pres-
sure of secondary pressure: 1.2 MPa
or more
2. When all of the following conditions are
satisfied:
- DTC other than the applicable DTC is not detected.
- CVT fluid temperature: More than - 20°C (-4 °F)
- Selector lever: Other than P/N position
- TCM power supply: More than 11 V
- When all of the following conditions are satisfied and this state is maintained
for 5.5 seconds:
• DTC other than the applicable DTC is not detected.
• CVT fluid temperature: More than - 20°C (-4 °F)
• Selector lever: Other than P/N position
• Secondary pressure - instruction pres- sure of secondary pressure: 1.2 MPa
or more
- The difference between instruction pressure of secondary pressure and
10-msec-ago instruction secondary
pressure is 0 MPa or more
- Secondary pressure - instruction pres- sure of secondary pressure: More than
1.2 MPa Secondary pressure solenoid valve
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

P0776 PRESSURE CONTROL SOLENOID BTM-331
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F10E]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROC EDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following condition for 20 seconds or more.
4. Stop the vehicle.
5. Check the first trip DTC.
Is
“P0776” detected?
YES >> Go to TM-331, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000009464285
1.CHECK INTERMITTENT INCIDNT
Refer to GI-43, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace transaxle assembly. Refer to TM-407, "Removal and Installation".
NO >> Repair or replace the malfunction items.
Selector lever : “D” position
Vehicle speed : 40 km/h (25 MPH) or more
Accelerator pedal position : 1.0/8 or more
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM