brake sensor NISSAN TEANA 2014 Workshop Manual

C1199 BRAKE BOOSTERBRC-103
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace malfunctioning components.
4.CHECK TERMINAL
• Check vacuum sensor pin terminals for damage or loose connection with harness connector.
• Check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
ness connector.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning components.
5.REPLACE VACUUM SENSOR
With CONSULT
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Replace vacuum sensor. Refer to BR-28, "Exploded View"
.
CAUTION:
Always replace brake booster because vac uum sensor cannot be disassembled.
3. Erase self-diagnosis result for “ABS”.
4. Turn the ignition switch OFF.
5. Start engine.
6. Perform self-diagnosis for “ABS”.
Is DTC
“C1199” detected?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-128, "Removal and Installa-
tion".
NO >> Inspection End.
Vacuum sensor —Continuity
Connector Terminal
E27 1
Ground No
2
3
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-104
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C119A VACUUM SENSOR
C119A VACUUM SENSOR
DTC LogicINFOID:0000000009463817
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULT
With CONSULT.
1. Turn the ignition switch ON.
2. Perform self-diagnostic result.
Is DTC C119A detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-104, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000009463818
Regarding Wiring Diagram information, refer to BRC-47, "Wiring Diagram".
1.CHECK VACUUM SENSOR POWER SUPPLY
1. Turn the ignition switch OFF.
2. Disconnect vacuum sensor harness connector.
3. Check voltage between vacuum sensor harness connector and ground.
4. Turn the ignition switch ON. CAUTION:
Never start engine.
5. Check voltage between vacuum sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK VACUUM SENSOR POWER SUPPLY CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check continuity between vacuum sensor harness connector and ABS ac tuator and electric unit (control
unit) harness connector.
DTC Display Item Malfunction detected condition Possible causes
C119A VACUUM SEN VOLT When a malfunction is detected in supply power volt-
age of vacuum sensor. • Harness or connector
• Vacuum sensor (brake booster)
• ABS actuator and electric unit (control unit)
Vacuum sensor —Voltag e
(Approx.)
Connector Terminal
E27 3 Ground 0 V
Vacuum sensor —Vo l ta g e
(Approx.)
Connector Terminal
E27 3 Ground 4.75 V – 5.25 V
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-116
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000009463838
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self-diagnosis.
NOTE:
• 1: The ABS does not operate when the speed is 10 km/h (6 MPH) or less.
• 2: Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly depressed (just place a foot on it).
However, this is normal.
- When shifting gears
- When driving on slippery road
- During cornering at high speed
- When passing over bumps or grooves [approximately 50 mm (1.97 in) or more]
- When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher] Symptom Check item Reference
Excessive ABS function operation fre-
quency Brake force distribution
BRC-117, "Diagno-
sis Procedure"Looseness of front and rear axle
Wheel sensor and rotor system
Unexpected pedal reaction Brake pedal stroke
BRC-118, "Diagno-
sis Procedure"Make sure the braking force is sufficient when the ABS is not operating.
The braking distance is long Check stopping distance when the ABS is not operating. BRC-119, "Diagno-
sis Procedure"
ABS function does not operate (Note 1) ABS ac
tuator and electric unit (control unit) BRC-120, "Diag-nosis Procedure"
Pedal vibration or ABS operation sound
occurs (Note 2) Brake pedal
BRC-121, "Diag-
nosis Procedure"ABS actuator and electric unit (control unit)
Vehicle jerks duri ng VDC/TCS/ABS con-
trol ABS actuator and electric unit (control unit)
BRC-122, "Diag-
nosis Procedure"TCM
ECM
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-117
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000009463839
1.CHECK START
Check front and rear brake force di stribution using a brake tester.
Is the inspection result normal?
YES >> GO TO 2
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Make sure that there is no excessive play in the front and rear axles. Refer to front: FAX-6, "Inspection"
, rear:
RAX-5, "On-vehicle Service"
.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace malfunctioning components.
3.CHECK WHEEL SENSOR AND SENSOR ROTOR
Check the following:
• Wheel sensor installation for damage
• Sensor rotor installation for damage
• Wheel sensor connector
• Wheel sensor harness
Is the inspection result normal?
YES >> GO TO 4
NO >> • Replace wheel sensor BRC-124, "Removal and Installation - Front Wheel Sensor"
or BRC-125,
"Removal and Installation - Rear Wheel Sensor".
• Replace sensor rotor BRC-127, "Removal and Installation - Front Sensor Rotor"
or BRC-127,
"Removal and Installation - Rear Sensor Rotor".
• Repair harness.
4.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp is turned off af ter the ignition switch is turned ON or when driving.
Is the inspection result normal?
YES >> Inspection End.
NO >> Perform self diagnostic result. Refer to BRC-33, "CONSULT Function (ABS)"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

NORMAL OPERATING CONDITIONBRC-123
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000009463845
Symptom Result
Slight vibrations are felt on the brake pedal and operation noises occur when VDC, TCS or ABS is activated. This is a normal condi-
tion due to the VDC,
TCS or ABS activation.
Stopping distance is longer than that of vehicles without ABS when the vehicle drives on rough, gravel, or
snow-covered (fresh, deep snow) roads.
The brake pedal moves and generates noises when TCS or VDC is activated due to rapid acceleration or
sharp turn.
The brake pedal vibrates and motor operation noises occur from the engine room after the engine starts and
just after the vehicle starts. This is normal, and it is
caused by the ABS op-
eration check.
Depending on the road conditions, the driver may experience a sluggish feel in the brake pedal. This is normal, because TCS places the highest
priority on the optimum
traction (stability).
TCS may activate momentarily if wheel speed changes when driving where road friction coefficient varies,
when downshifting, or when fully depressing accelerator pedal.
The ABS warning lamp and SLIP indicator lamp may turn ON when the vehicle is subject to strong shaking
or large vibration, such as when the vehicle is rotating on a turntable or located on a ship while the engine
is running. In this case, restart the
engine on a normal
road. If the normal con-
dition is restored, there
is no malfunction. At
that time, erase the self-
diagnosis memory.
VDC may not operate normally or th
e ABS warning lamp, and SLIP indicato r lamp may illuminate when driv-
ing on a road that is extremely slanted (e.g., bank in a circuit course).
A malfunction may occur in the yaw rate/side/decel G sensor system when the vehicle turns sharply, such
as during a spin turn, axle turn, or drift driving, while the VDC function is OFF (VDC OFF indicator lamp illu-
minated).
The vehicle speed will not increase even though the accelerator pedal is depressed, when inspecting the
speedometer on a 2-wheel chassis dynamometer. Normal (Deactivate the
VDC/TCS function be-
fore performing an in-
spection on a chassis
dynamometer.)
SLIP indicator lamp may simultaneously turn ON when low tire pressure warning lamp turns ON. This is not a VDC sys-
tem error but results
from characteristic
change of tire.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-129
< REMOVAL AND INSTALLATION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
3. Remove the power steering line hold down bracket.
4. Disconnect ABS actuator and el ectric unit (control unit) harness connector and place aside.
5. Loosen brake tube flare nuts using a suitable tool, t hen remove brake tubes from ABS actuator and elec-
tric unit (control unit) and place aside. Refer to BRC-128, "Exploded View"
.
6. Remove the harness bracket bolt and place aside.
7. Remove ABS actuator and electric unit (control unit) and bracket as an assembly.
8. Remove bracket from ABS actuator and el ectric unit (control unit), if necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
If ABS actuator and electronic unit (control unit) is replaced, after installation, adjust position of steer-
ing angle sensor. Refer to BRC-58, "Work Procedure"
.
ALFIA0306ZZ
ALFIA0302ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-44
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
* : Initial setting
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)INFOID:0000000009952502
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a di scharged battery and a no-start condition.
SELF DIAGNOSTIC RESULT
Refer to BCS-52, "DTC Index".
DATA MONITOR
AUTO LOCK FUNCTION MODE3 This mode is not used.
MODE2 Doors lock automatically when shifted out of P (park).
MODE1* Doors lock automatically when vehicle speed reaches 24 km/h (15 mph).
Off —
AUTO UNLOCK FUNCTION MODE3 This mode is not used.
MODE2 Doors unlock automatically when shifted into P (park).
MODE1* Doors unlock automatically when ignition is switched from ON to OFF.
Off —
Support Item Setting Description
Monitor Item [Unit] Main Description
REQ SW -DR [On/Off] ×Indicates condition of door request switch LH.
REQ SW -AS [On/Off] ×Indicates condition of door request switch RH.
REQ SW -BD/TR [On/Off] ×Indicates condition of trunk opener request switch.
PUSH SW [On/Off] Indicates condition of push-button ignition switch.
SHFTLCK SLNID PER SPLY [On/Off] ×Indicates condition of power supply to shiftlock solenoid.
BRAKE SW 1 [On/Off] ×Indicates condition of brake switch.
BRAKE SW 2 [On/Off] Indicates condition of brake switch.
DETE/CANCL SW [On/Off] ×Indicates condition of P (park) position.
SFT PN/N SW [On/Off] ×Indicates condition of P (park) or N (neutral) position.
UNLK SEN -DR [On/Off] ×Indicates condition of door unlock sensor.
PUSH SW -IPDM [On/Off] Indicates condition of push-button ignition switch received from IPDM E/R
on CAN communication line.
IGN RLY1 -F/B [On/Off] Indicates condition of ignition relay 1 received from IPDM E/R on CAN
communication line.
DETE SW -IPDM [On/Off] Indicates condition of detent switch received from TCM on CAN communi-
cation line.
SFT PN -IPDM [On/Off] Indicates condition of P (park) or N (neutral) position from TCM on CAN
communication line.
SFT P -MET [On/Off] Indicates condition of P (park) position from TCM on CAN communication
line.
SFT N -MET [On/Off] Indicates condition of N (neutral) position from IPDM E/R on CAN commu-
nication line.
ENGINE STATE [STOP/START/CRANK/RUN] ×Indicates condition of engine state from ECM on CAN communication line.
VEH SPEED 1 [mph/km/h] ×Indicates condition of vehicle speed signal received from ABS on CAN
communication line.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-1
ENGINE
C
D E
F
G H
I
J
K L
M
SECTION EC
A
EC
N
O P
CONTENTS
ENGINE CONTROL SYSTEM
QR25DE
PRECAUTION ................ ..............................
15
PRECAUTIONS .............................................. ....15
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
15
Precaution for Procedure without Cowl Top Cover ....15
On Board Diagnostic (OBD) System of Engine
and CVT .............................................................. ....
15
General Precautions ...............................................16
PREPARATION ...........................................19
PREPARATION .............................................. ....19
Special Service Tools .......................................... ....19
Commercial Service Tools ......................................19
SYSTEM DESCRIPTION .............................21
COMPONENT PARTS ................................... ....21
Component Parts Location ................................ ....21
ECM ........................................................................25
Accelerator Pedal Position Sensor ...................... ....25
Electric Throttle Control Actuator ........................ ....25
Ignition Coil With Power Transistor .........................26
Fuel Injector ........................................................ ....26
Fuel Level Sensor Unit and Fuel Pump .............. ....26
Fuel Tank Temperature Sensor .......................... ....27
Mass Air Flow Sensor (With Intake Air Tempera-
ture Sensor) ........................................................ ....
27
Manifold Absolute Pressure Sensor ........................28
Engine Coolant Temperature Sensor .................. ....28
Crankshaft Position Sensor (POS) ..........................29
Camshaft Position Sens or (PHASE) .......................29
Intake Valve Timing Cont rol Solenoid Valve ...........30
Intake Valve Timing Intermediate Lock Control
Solenoid Valve .................................................... ....
30
Exhaust Valve Timing Control Position Sensor .......30
Exhaust Valve Timing Control Solenoid Valve ........31
Intake Manifold Runner Control Valve ................. ....31
Intake Manifold Tuning Valve ..................................31
Air Fuel Ratio (A/F) Sensor 1 ..................................32
Heated Oxygen Sensor 2 ........................................32
Knock Sensor ..........................................................33
Engine Oil Pressure Sensor ....................................33
Engine Oil Temperature Sensor .......................... ....33
Cooling Fan .............................................................34
EVAP Canister .........................................................34
EVAP Canister Purge Volu me Control Solenoid
Valve .................................................................... ....
34
EVAP Canister Vent Control Valve ..........................35
EVAP Control System Pres sure Sensor ..................35
Battery Current Sensor (With Battery Tempera-
ture Sensor) ......................................................... ....
35
Malfunction Indicator lamp (MIL) .............................36
Oil Pressure Warning Lamp ....................................36
Refrigerant Pressure Sensor ............................... ....36
Stop Lamp Switch & Brake Pedal Position Switch ....36
ASCD Steering Switch .............................................37
Information Display ..................................................37
STRUCTURE AND OPERATION .....................38
Positive Crankcase Ventilation ................................38
On Board Refueling Vapor Recovery (ORVR) ........39
SYSTEM ............................................................40
ENGINE CONTROL SYSTEM ........................ ...........40
ENGINE CONTROL SYSTEM : System Descrip-
tion ....................................................................... ....
40
ENGINE CONTROL SYSTEM : Fail Safe ..............41
MULTIPORT FUEL INJECTION SYSTEM ................43
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description (with auto matic air conditioner) ......
43
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description (with manual air conditioner) .........
46
ELECTRIC IGNITION SYSTEM .................................48
ELECTRIC IGNITION SYSTEM : System De-
scription ............................................................... ....
48
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-6
Diagnosis Procedure .............................................408
P0850 PNP SWITCH .......................................410
Description ........................................................... ..410
DTC Logic ..............................................................410
Component Function Check ..................................411
Diagnosis Procedure .............................................411
P1078 EVT CONTROL POSITION SENSOR ..413
DTC Logic ............................................................ ..413
Diagnosis Procedure .............................................413
Component Inspection ...........................................415
P1148 CLOSED LOOP CONTROL .................416
DTC Logic ............................................................ ..416
Diagnosis Procedure .............................................416
P117A AIR FUEL RATIO .................................417
DTC Logic ............................................................ ..417
Diagnosis Procedure .............................................418
P1212 TCS COMMUNICATION LINE .............422
Description ........................................................... ..422
DTC Logic ..............................................................422
Diagnosis Procedure .............................................422
P1217 ENGINE OVER TEMPERATURE .........423
DTC Logic ............................................................ ..423
Component Function Check ..................................423
Diagnosis Procedure .............................................424
P1225 TP SENSOR .........................................426
DTC Logic ............................................................ ..426
Diagnosis Procedure .............................................426
P1226 TP SENSOR .........................................427
DTC Logic ............................................................ ..427
Diagnosis Procedure .............................................427
P1550 BATTERY CURRENT SENSOR ..........428
DTC Logic ............................................................ ..428
Diagnosis Procedure .............................................428
Component Inspection ...........................................429
P1551, P1552 BATTERY CURRENT SEN-
SOR ................................................................. .
431
DTC Logic ............................................................ ..431
Diagnosis Procedure .............................................431
Component Inspection ...........................................432
P1553 BATTERY CURRENT SENSOR ..........434
DTC Logic ............................................................ ..434
Diagnosis Procedure .............................................434
Component Inspection ...........................................435
P1554 BATTERY CURRENT SENSOR ..........437
DTC Logic ............................................................ ..437
Component Function Check ..................................437
Diagnosis Procedure .............................................438
Component Inspection ...........................................439
P1556, P1557 BATTERY TEMPERATURE
SENSOR ......................................................... ..
440
DTC Logic ............................................................ .440
Diagnosis Procedure .............................................440
Component Inspection ..........................................441
P1564 ASCD STEERING SWITCH ..................442
DTC Logic ............................................................ .442
Diagnosis Procedure .............................................442
Component Inspection ..........................................444
P1572 ASCD BRAKE SWITCH ........................445
DTC Logic ............................................................ .445
Diagnosis Procedure .............................................446
Component Inspection (Brake Pedal Position
Switch) ................................................................. .
449
Component Inspection (Stop Lamp Switch) ..........450
Component Inspection (Stop Lamp Relay) ...........450
P1574 ASCD VEHICLE SPEED SENSOR ..... ..452
Description ........................................................... .452
DTC Logic .............................................................452
Diagnosis Procedure .............................................452
P1715 INPUT SPEED SENSOR .......................454
Description ........................................................... .454
DTC Logic .............................................................454
Diagnosis Procedure .............................................454
P1800 INTAKE MANIFOLD TUNING VALVE ..456
DTC Logic .............................................................456
Diagnosis Procedure .............................................456
Component Inspection ..........................................457
P1805 BRAKE SWITCH ................................. ..459
DTC Logic ............................................................ .459
Diagnosis Procedure .............................................459
Component Inspection (Stop Lamp Switch) ..........461
Component Inspection (Stop Lamp Relay) ...........461
P2004 INTAKE MANIFOLD RUNNER CON-
TROL VALVE ................................................. ..
462
DTC Logic ............................................................ .462
Diagnosis Procedure .............................................462
Component Inspection ..........................................463
P2014, P2016, P2017, P2018 INTAKE MANI-
FOLD RUNNER CONTROL VALVE POSI-
TION SENSOR ............................................... ..
465
DTC Logic ............................................................ .465
Diagnosis Procedure .............................................465
P2096, P2097 A/F SENSOR 1 .........................468
DTC Logic ............................................................ .468
Diagnosis Procedure .............................................468
P2100, P2103 THROTTLE CONTROL MO-
TOR RELAY ................................................... ..
472
DTC Logic ............................................................ .472
Diagnosis Procedure .............................................472
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-7
C
D E
F
G H
I
J
K L
M
EC A
N
O P
P2101 ELECTRIC THROTTLE CONTROL
FUNCTION ..................................................... ..
475
DTC Logic ........................................................... ..475
Diagnosis Procedure .............................................475
Component Inspection ..........................................477
P2118 THROTTLE CONTROL MOTOR ..........478
DTC Logic ........................................................... ..478
Diagnosis Procedure .............................................478
Component Inspection ..........................................479
P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR .................................................... ..
480
DTC Logic ........................................................... ..480
Diagnosis Procedure .............................................480
P2122, P2123 APP SENSOR ...........................482
DTC Logic ........................................................... ..482
Diagnosis Procedure .............................................482
Component Inspection ..........................................484
P2127, P2128 APP SENSOR ...........................485
DTC Logic ........................................................... ..485
Diagnosis Procedure .............................................485
Component Inspection ..........................................486
P2135 TP SENSOR ..........................................488
DTC Logic ........................................................... ..488
Diagnosis Procedure .............................................488
Component Inspection ..........................................490
P2138 APP SENSOR .......................................491
DTC Logic ........................................................... ..491
Diagnosis Procedure .............................................491
Component Inspection ..........................................493
P2610 ECM INTERNAL TIMER .......................494
Description .......................................................... ..494
DTC Logic .............................................................494
Diagnosis Procedure .............................................495
BRAKE PEDAL POSITION SWITCH ...............496
Component Function Check ................................ ..496
Diagnosis Procedure .............................................496
Component Inspection (Brake Pedal Position
Switch) ................................................................ ..
497
COOLING FAN .................................................499
Component Function Check ................................ ..499
Diagnosis Procedure .............................................499
Component Inspection (Cooling Fan Motor) .........501
Component Inspection (C ooling Fan Relay) .........502
ELECTRICAL LOAD SIGNAL ....................... ..503
Description .......................................................... ..503
Component Function Check ..................................503
Diagnosis Procedure .............................................503
FUEL INJECTOR .............................................505
Component Function Check ................................ ..505
Diagnosis Procedure .............................................505
Component Inspection ......................................... ..506
FUEL PUMP ....................................................508
Description .............................................................508
Component Function Check ..................................508
Diagnosis Procedure .............................................508
Component Inspection ...........................................510
IGNITION SIGNAL ..........................................511
Component Function Check ..................................511
Diagnosis Procedure .............................................511
Component Inspection (Ignition Coil with Power
Transistor) ........................................................... ..
514
Component Inspection (Condenser) ......................515
INFORMATION DISPLAY (ASCD) .................516
Component Function Check ..................................516
Diagnosis Procedure .............................................516
MALFUNCTION INDICATOR LAMP ..............517
Component Function Check ..................................517
Diagnosis Procedure .............................................517
ON BOARD REFUELING VAPOR RECOV-
ERY (ORVR) ....................................................
518
Component Function Check ................................ ..518
Diagnosis Procedure .............................................518
Component Inspection ...........................................520
REFRIGERANT PRESSURE SENSOR ..........523
Component Function Check ..................................523
Diagnosis Procedure .............................................523
SENSOR POWER SUPPLY 2 CIRCUIT .........525
Description .............................................................525
Diagnosis Procedure .............................................525
SYMPTOM DIAGNOSIS ............................527
ENGINE CONTRO L SYSTEM ........................527
Symptom Table ................................................... ..527
INFORMATION DISPLAY IS MALFUNCTION-
ING ..................................................................
532
Diagnosis Procedure ........................................... ..532
NORMAL OPERATING CONDITION .............533
Description .............................................................533
PERIODIC MAINTENANCE ......................534
IDLE SPEED .... ...............................................534
Inspection ............................................................ ..534
IGNITION TIMING ...........................................535
Inspection ..............................................................535
EVAPORATIVE EMISSION SYSTEM .............536
Inspection ..............................................................536
EVAP LEAK CHECK ......................................537
Inspection ..............................................................537
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM