seats NISSAN TEANA 2014 Manual PDF

FRONT SEATSE-63
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
3. Release the J-clips (A) holding the seatback trim (1) to the seat- back frame.
4. Remove the rear hinge cover (1).
5. Unclip the side air bag module harness at locations (B). NOTE:
Take note of harness routing and attachment location for accu-
rate installation.
6. From the bottom of the seat.
a. Unclip the side air bag module harness (1) at locations (A). NOTE:
Take note of harness routing and attachment location for accu-
rate installation.
b. Disconnect the harness connector (B) from the seatback heater
(if equipped).
(C) Harness connector for seat cushion heater
7. Release the headrest holder locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing th e headrest holder, check its
orientation (front/rear and right/left).
8. Remove and discard the two side air bag module nuts (A). (1) Side air bag module
CAUTION:
Do not reuse the side air bag module nuts.
ALJIA0972ZZ
ALJIA0964ZZ
PIIB4084J
ALJIA0971ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-65
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
• When installing the side air bag module, make sure the side air bag chute (4) is pulled over the outboard surface of the side air bag
module (3). Make sure there are no wrinkles and the chute is not
folded, twisted or pinched.
(1) Seatback pad
(2) Frame
(5) Seatback board
: Front
• Tighten the side air bag nuts to specification. Refer to SE-54,
"PASSENGER SIDE : Exploded View".
CAUTION:
• Do not reuse side air bag module nuts.
ALJIA0682ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-67
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
7. Armrest 8. Cup holder 9. Armrest hinge finisher
10. Seatback hinge assembly (RH) 11. Seat cushion assembly 12. Seat cushion wire cover
13. Seat cushion lock 14. Seat cushion pad 15. Seat cushion trim
16. Seatback hinge (LH) 17. Seatback pad (LH) 18. Seatback trim (LH)
19. Seatback board (LH) 20. Seat belt guide (LH) 21. Rear seat bolster (LH)
22. Rear seatback assembly (LH) 23. Seatback latch assembly 24. Cable guide
A. Seatback board clips B. Armrest pivot bolt
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-69
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
Disassembly and AssemblyINFOID:0000000009462955
SEAT CUSHION
Disassembly
1. Remove the seat cushion assembly. Refer to SE-36, "Removal and Installation - Seat Cushion Assembly".
2. Remove the two clips that retain the seat cushion trim.
3. Release the fastening strips from the seat cushion frame.
4. Remove the seat cushion trim and seat cushion pad from the seat cushion frame.
5. Separate the seat cushion trim from the seat cushion pad.
a. Pull the seat cushion trim upward to release hook fasteners.
b. Remove the six hog rings and separate the seat cushion trim from the seat cushion pad. NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Make sure hog rings are correctly fastened around both the seat cushion trim and seat cushion pad
wires.
• Replace any deformed or damaged hog rings.
19. Seatback hinge (LH) 20. Seatback pad (LH) 21. Seatback trim (LH)
22. Headrest holder (LH) (locked) 23. Headrest holder (LH) (free) 24. Seatback board (LH)
25. Rear seatback assembly (LH) 26. Seat belt guide (LH) 27. Rear seat bolster (LH)
28. Headrest (LH) 29. Seatback latch assembly 30. Cable guide
A. Seatback board clips B. Armrest pivot bolt
1. Seat cushion frame 2. Seat cushion pad 3. Seat cushion trim
A. Fastening strips B. Hook fasteners Hog rings
Clips
ALJIA0960ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-71
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
c. Release the headrest holder locks as shown and remove the headrest holders (1) from the seatback frame (2).
CAUTION:
Before removing headrest holder, check its orientation
(front/rear and right/left).
d. Remove the seatback trim and seatback pad from the seatback frame.
5. Separate the seatback trim from the seatback pad.
a. Pull seatback trim (1) upward to release hook fasteners (A).
b. Remove three hog rings and separate the seatback trim from the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Make sure hog rings are correctly fastened ar ound both the seatback trim and seatback pad wires.
• Replace any deformed or damaged hog rings.
• Make sure any old hog ring pieces are removed from seat.
NOTE:
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• When installing the seatback trim, firmly push down while sliding your hand along the seams as shown ( ) to ensure the hook fas-
teners below the seatback trim are fastened properly.
ALJIA0943ZZ
ALJIA0944ZZ
PIIB3356J
ALJIA0656ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-73
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• When installing the seatback trim, firmly push down while sliding
your hand along the seams as shown ( ) to ensure the hook fas-
teners below the seatback trim are fastened properly.
REAR SEATBACK ASSEMBLY (LH) - WITH REMOVABLE HEADREST
Disassembly
1. Remove the rear seatback assembly (LH). Refer to SE-36, "Removal and Installation - Seat Assembly".
2. Release the J-clip retainer (B) and unzip the seatback trim cover (1).
(A) Zipper
3. Remove the seatback trim and seatback pad (2) from the seat- back frame (1).
a. Release the J-clip retainer (A).
PIIB3356J
ALJIA0656ZZ
ALJIA0945ZZ
ALJIA0946ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR SEATSE-75
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
Disassembly
1. Remove the rear seatback assembly (LH). Refer to
SE-36, "Removal and Installation - Seat Assembly".
2. Release the J-clip retainer (B) and unzip the seatback trim cover (1).
(A) Zipper
3. Remove the seatback trim and seatback pad (2) from the seat- back frame (1).
a. Release the J-clip retainer (A).
b. Remove the seatback trim and seatback pad from the seatback frame.
4. Separate the seatback trim (1) from the seatback pad.
a. Pull seatback trim upward to release hook fasteners (A).
b. Remove three hog rings and separate the seatback trim from the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Make sure hog rings are correctly fastened ar ound both the seatback trim and seatback pad wires.
• Replace any deformed or damaged hog rings.
• Make sure any old hog ring pieces are removed from seat.
NOTE:
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
ALJIA0945ZZ
ALJIA0946ZZ
ALJIA0967ZZ
PIIB3356J
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SEC-4
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951563
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for WorkINFOID:0000000009461062
• When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a s hop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PRECAUTIONSSR-3
< PRECAUTION >
C
D E
F
G
I
J
K L
M A
B
SR
N
O P
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
-Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: November 20132014 Altima NAM

ST-4
< PRECAUTION >
PRECAUTIONS
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirtyarea.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM