glove box NISSAN TIIDA 2007 Service Manual PDF

VTL-28
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
PTC HEATER
PTC HEATER
Removal and Installation of PTC Control UnitINFOID:0000000001696502
REMOVAL
1. Remove the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to IP-11,
"Removal and Installation".
2. Remove the glove box assembly and instrument lower cover (RH) for RHD only. Refer to IP-11, "
Removal
and Installation".
3. Disconnect the PTC control unit connector (A).
4. Remove the PTC control unit screws (B), and then remove the
PTC control unit (1).
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation of PTC HeaterINFOID:0000000001696503
REMOVAL
1. Remove the instrument panel and pad. Refer to IP-11, "Removal and Installation".
2. Disconnect the PTC heater connector and full hot switch connector.
3. Remove the PTC heater and full hot switch screws (A), and then
remove the PTC heater (1) and full hot switch (2).
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation of Water Temperature SensorINFOID:0000000001696504
REMOVAL
1. Remove the A/C unit assembly. Refer to VTL-12, "Removal and Installation".
2. Remove the heater pipe cover. Refer to VTL-39, "
Disassembly and Assembly".
SJIA0776E
SJIA0774E

AIR CONDITIONER FILTER
VTL-33
< ON-VEHICLE MAINTENANCE >[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
ON-VEHICLE MAINTENANCE
AIR CONDITIONER FILTER
Removal and InstallationINFOID:0000000001710936
REPLACEMENT TIMING
Replace the air conditioner filter according to the maintenance schedules. Refer to MA-7, "Periodic Mainte-
nance".
NOTE:
The air conditioner filter caution label is located inside the glove box door.
REPLACEMENT PROCEDURES
1. Remove the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to IP-11,
"Removal and Installation".
2. Remove the glove box assembly and instrument lower cover (RH) for RHD only. Refer to IP-11, "
Removal
and Installation".
3. Compress the air conditioner filter (1) downward while sliding it
to the RH side of the vehicle to release the upper pawl.
4. Move the bottom of air conditioner filter (1) upward as shown to
release the bottom tab, then remove it.
5. Replace the air conditioner filter with new one and install the new filter in the A/C unit assembly.
CAUTION:
Make sure that the air conditioner filter lower tab is fully seated, and that the air conditioner upper
pawl is locked into place securing the new filter into the A/C unit assembly.
6. Install the glove box assembly and instrument lower cover (RH) for RHD only. Refer to IP-11, "
Removal
and Installation".
7. Install the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to IP-11,
"Removal and Installation".
SJIA0652E

VTL-44
< ON-VEHICLE REPAIR >[MANUAL AIR CONDITIONER]
BLOWER FAN RESISTOR
BLOWER FAN RESISTOR
Removal and InstallationINFOID:0000000001696536
REMOVAL
1. Remove the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to IP-11,
"Removal and Installation".
2. Remove the glove box assembly and instrument lower cover (RH) for RHD only. Refer to IP-11, "
Removal
and Installation".
3. Remove the console side cover. Refer to IP-10, "
Component Parts".
4. Remove the brake pedal assembly for LHD only. Refer to BR-12, "
Removal and Installation".
5. Disconnect the blower fan resistor connector.
6. Remove the blower fan resistor screws (A), then remove the
blower fan resistor (1).
INSTALLATION
Installation is in the reverse order of removal.
SJIA0656E

INTAKE DOOR
VTL-45
< ON-VEHICLE REPAIR >[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
INTAKE DOOR
Intake Door Cable AdjustmentINFOID:0000000001696537
1. Remove the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to IP-11,
"Removal and Installation".
2. Remove the glove box assembly and instrument lower cover (RH) for RHD only. Refer to IP-11, "
Removal
and Installation".
3. Remove outer cable of intake door cable (1) from clamp (A).
4. Set intake door lever to REC position.
5. Push intake door link (2) in the direction shown by the arrow,
and then carefully pull outer cable to controller side, and install
clamp (A).
6. Operate intake door lever to insure that inner cable moves
smoothly.
CAUTION:
When clamping the outer cable, do not move the inner
cable.
SJIA0650E

MODE DOOR
VTL-47
< ON-VEHICLE REPAIR >[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
MODE DOOR
Mode Door Cable AdjustmentINFOID:0000000001696539
1. Remove the glove box assembly and instrument lower cover (RH) for LHD only. Refer to IP-11, "Removal
and Installation".
2. Remove the instrument lower finisher and instrument lower cover (LH) for RHD only. Refer to IP-11,
"Removal and Installation".
3. Remove outer cable of mode door cable (1) from clamp (A).
4. Set mode control dial to VENT position.
5. Push main link (2) in the direction shown by the arrow, and then
carefully pull outer cable to controller side, and install clamp (A).
6. Operate mode control dial to insure that inner cable moves
smoothly.
CAUTION:
When clamping the outer cable, do not move the inner
cable.
7. Turn mode control dial to each position.
8. Confirm that discharge air comes out according to the air distribution table. Refer to HAC-11, "
Discharge
Air Flow".
SJIA0654E

PTC HEATER
VTL-53
< ON-VEHICLE REPAIR >[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
PTC HEATER
Removal and Installation of PTC Control UnitINFOID:0000000001696541
REMOVAL
1. Remove the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to IP-11,
"Removal and Installation".
2. Remove the glove box assembly and instrument lower cover (RH) for RHD only. Refer to IP-11, "
Removal
and Installation".
3. Disconnect connector (A).
4. Remove mounting screws (B), and then remove PTC control
unit (1).
INSTALLATION
Installation is basically the reverse order of removal.
Removal and Installation of PTC HeaterINFOID:0000000001696542
REMOVAL
1. Remove instrument panel and pad. Refer to IP-11, "Removal and Installation".
2. Disconnect PTC heater connector and full hot switch connector.
3. Remove mounting screws (A), and then remove PTC heater (1)
and full hot switch (2).
INSTALLATION
Installation is basically the reverse order of removal.
Removal and Installation of Water Temperature SensorINFOID:0000000001696543
REMOVAL
1. Remove A/C unit assembly. Refer to VTL-37, "Removal and Installation".
2. Remove heater pipe cover. Refer to VTL-39, "
Disassembly and Assembly".
SJIA0776E
SJIA0774E

WCS
WARNING CHIME SYSTEM
WCS-5
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
MB A
O
P
WARNING CHIME SYSTEM : Component Parts LocationINFOID:0000000001722906
AWNIA0259ZZ
1. Combination meter M24 2. BCM M18 (view with glove box re-
moved)3. Key switch and key lock solenoid M27
(without Intelligent Key)
4. Key switch and ignition knob switch
M32 (with Intelligent Key)5. Combination switch (lighting switch)
M286. Front door switch (driver side) B9

WCS-8
< FUNCTION DIAGNOSIS >
WARNING CHIME SYSTEM
LIGHT REMINDER WARNING CHIME : Component Parts Location
INFOID:0000000001728298
AWNIA0259ZZ
1. Combination meter M24 2. BCM M18 (view with glove box re-
moved)3. Key switch and key lock solenoid M27
(without Intelligent Key)
4. Key switch and ignition knob switch
M32 (with Intelligent Key)5. Combination switch (lighting switch)
M286. Front door switch (driver side) B9

WCS-10
< FUNCTION DIAGNOSIS >
WARNING CHIME SYSTEM
SEAT BELT WARNING CHIME : Component Parts Location
INFOID:0000000001728299
AWNIA0259ZZ
1. Combination meter M24 2. BCM M18 (view with glove box re-
moved)3. Key switch and key lock solenoid M27
(without Intelligent Key)
4. Key switch and ignition knob switch
M32 (with Intelligent Key)5. Combination switch (lighting switch)
M286. Front door switch (driver side) B9

WCS-12
< FUNCTION DIAGNOSIS >
WARNING CHIME SYSTEM
KEY WARNING CHIME (WITH INTELLIGENT KEY) : Component Parts Location
INFOID:0000000001728300
AWNIA0259ZZ
1. Combination meter M24 2. BCM M18 (view with glove box re-
moved)3. Key switch and key lock solenoid M27
(without Intelligent Key)
4. Key switch and ignition knob switch
M32 (with Intelligent Key)5. Combination switch (lighting switch)
M286. Front door switch (driver side) B9