fuel NISSAN X-TRAIL 2003 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: X-TRAIL, Model: NISSAN X-TRAIL 2003Pages: 4179, PDF Size: 87.27 MB
Page 3702 of 4179
DI-24
COMBINATION METERS
4. CHECK GROUND CIRCUIT
Check continuity between fuel level sensor unit harness connector
B31
*1 or B123*2 terminal 1 (B) and ground.
NOTE:
*1: LHD models, *2: RHD models
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK FUEL LEVEL SENSOR
Check fuel level sensor units. Refer to DI-30, "
FUEL LEVEL SENSOR UNIT CHECK/GASOLINE ENGINE
MODELS" .
OK or NG
OK >> GO TO 6.
NG >> Replace fuel level sensor unit or sub fuel level sensor unit.
6. CHECK INSTALLATION CONDITION
Check fuel level sensor unit installation, and check whether the float arm interferes or binds with any of the
internal components in the fuel tank.
OK or NG
OK >> Replace combination meter.
NG >> Install fuel level sensor unit properly.
Fuel Level Sensor Inspection [Diesel Engine Models]EKS00EJA
The following symptoms do not indicate a malfunction.
FUEL GAUGE
Depending on vehicle posture or driving circumstance, the fuel level changes and the pointer may fluctu-
ate.
If the vehicle is fueled with the ignition switch ON, the pointer will move slowly.
LOW-FUEL WARNING LAMP
Depending on vehicle posture or driving circumstance, the fuel level changes and the warning lamp ON timing
may change.
1. CHECK HARNESS CONNECTOR
Check combination meter and fuel level sensor unit terminals (meter side, unit side harness side) for loose-
ness or bent terminals.
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.Continuity should exist.
SKIA8926E
Page 3703 of 4179
COMBINATION METERS
DI-25
C
D
E
F
G
H
I
J
L
MA
B
DI
2. CHECK COMBINATION METER CIRCUIT
1. Disconnect combination meter connector and sub fuel level sen-
sor unit connector.
2. Check continuity between combination meter harness connector
M44 terminal 8 (G) and sub fuel level sensor unit harness con-
nector B125
*1 or B21*2 terminal 1 (G).
3. Check continuity between combination meter harness connector
M44 terminal 8 (G) and ground.
NOTE:
*1: LHD models, *2: RHD models
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK FUEL LEVEL SENSOR CIRCUIT
1. Disconnect fuel level sensor unit connector.
2. Check continuity between sub fuel level sensor unit harness
connector B125
*1 or B21*2 terminal 3 (Y) and fuel level sensor
unit harness connector B32
*1 or B124*2 terminal 4 (Y).
3. Check continuity between sub fuel level sensor unit harness
connector B125
*1 or B21*2 terminal 3 (Y) and ground.
NOTE:
*1: LHD models, *2: RHD models
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4. CHECK GROUND CIRCUIT
Check continuity between fuel level sensor unit harness connector
B32
*1 or B124*2 terminal 1 (B) and ground.
NOTE:
*1: LHD models, *2: RHD models
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.Continuity should exist.
Continuity should not exist.
SKIA8924E
Continuity should exist.
Continuity should not exist.
SKIA9172E
Continuity should exist.
SKIA9173E
Page 3704 of 4179
DI-26
COMBINATION METERS
5. CHECK FUEL LEVEL SENSOR
Check fuel level sensor units. Refer to DI-30, "
FUEL LEVEL SENSOR UNIT CHECK/DIESEL ENGINE MOD-
ELS" .
OK or NG
OK >> GO TO 6.
NG >> Replace fuel level sensor unit or sub fuel level sensor unit.
6. CHECK INSTALLATION CONDITION
Check fuel level sensor unit installation, and check whether the float arm interferes or binds with any of the
internal components in the fuel tank.
OK or NG
OK >> Replace combination meter.
NG >> Install fuel level sensor unit properly.
Engine Speed Signal Inspection EKS00EHD
1. CHECK ECM SELF-DIAGNOSIS
Perform ECM self-diagnosis. Refer to EC-102, "
CONSULT-II Function" [QR (WITH EURO-OBD)], EC-551,
"CONSULT-II Function" [QR (WITHOUT EURO -OBD)] or EC-926, "CONSULT-II Function" [YD].
OK or NG
OK >> Replace combination meter.
NG >> Perform “Diagnostic Procedure” in displayed DTC.
Water Temperature Signal InspectionEKS00EHE
1. CHECK ECM SELF-DIAGNOSIS
Perform ECM self-diagnosis. Refer to EC-102, "
CONSULT-II Function" [QR (WITH EURO-OBD)], EC-551,
"CONSULT-II Function" [QR (WITHOUT EURO -OBD)] or EC-926, "CONSULT-II Function" [YD].
OK or NG
OK >> Replace combination meter.
NG >> Perform “Diagnostic Procedure” in displayed DTC.
Vehicle Speed Signal Inspection [with ESP]EKS00EHF
1. CHECK ESP/TCS/ABS CONTROL UNIT SELF-DIAGNOSIS
Preform ESP/TCS/ABS control unit self-diagnosis. Refer to BRC-77, "
CONSULT-II Functions" .
OK or NG
OK >> Replace combination meter.
NG >> Check applicable parts.
Vehicle Speed Signal Inspection [without ESP]EKS00EJB
1. CHECK ABS ACTUATOR CONTROL UNIT SELF-DIAGNOSIS
Preform ABS actuator and electric unit self-diagnosis. Refer to BRC-25, "
CONSULT- II Functions" .
OK or NG
OK >> Replace combination meter.
NG >> Check applicable parts.
Page 3705 of 4179
COMBINATION METERS
DI-27
C
D
E
F
G
H
I
J
L
MA
B
DI
The Fuel Gauge Pointer Fluctuates, Indicator Wrong Value or VariesEKS00EHG
1. CHECK FUEL GAUGE FLUCTUATION
Test drive vehicle to see if gauge fluctuates only during driving and just before or soon after stopping.
Does the indication value vary only during driving and just before or soon after stopping?
YES >> The pointer fluctuation may be caused by fuel level change in the fuel tank. Condition is normal.
NO >> Ask the customer about the situation when the symptom occurs in detail, and perform the trouble
diagnosis.
The Fuel Gauge Does Not Move to FULL positionEKS00EHH
1. QUESTION 1
Does it take a long time for the pointer to move to FULL position?
YES or NO
YES >> GO TO 2.
NO >> GO TO 3.
2. QUESTION 2
Was the vehicle fueled with the ignition switch ON?
YES or NO
YES >> Be sure to fuel the vehicle with the ignition switch OFF. Otherwise, it will take a long time to move
to FULL position because of the characteristic of the fuel gauge.
NO >> GO TO 3.
3. QUESTION 3
Is the vehicle parked on an incline?
YES or NO
YES >> Check the fuel level indication with vehicle on a level surface.
NO >> GO TO 4.
4. QUESTION 4
During driving, does the fuel gauge pointer move gradually toward EMPTY position?
YES or NO
YES >> Check fuel level sensor unit. Refer to DI-30, "FUEL LEVEL SENSOR UNIT CHECK/GASOLINE
ENGINE MODELS" or DI-30, "FUEL LEVEL SENSOR UNIT CHECK/DIESEL ENGINE MOD-
ELS" .
NO >> The float arm may interfere or bind with any of the components in the fuel tank.
Page 3708 of 4179
DI-30
COMBINATION METERS
Electrical Components InspectionEKS00INH
FUEL LEVEL SENSOR UNIT CHECK/GASOLINE ENGINE MODELS
For removal, refer to FL-4, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY" for
Gasoline engine models.
Fuel level sensor unit
Check the resistance between terminals 1 and 4.
*1 and *2: When float rod is in contact with stopper.
Sub fuel level sensor unit
Check the resistance between terminals 1 and 3.
*1 and *2: When float rod is in contact with stopper.
FUEL LEVEL SENSOR UNIT CHECK/DIESEL ENGINE MODELS
For removal, refer to FL-19, "FUEL LEVEL SENSOR UNIT" for Diesel engine models.
Fuel level sensor unit
Check the resistance between terminals 1 and 4.
*1 and *2: When float rod is in contact with stopper.
Sub fuel level sensor unit
Check the resistance between terminals 1 and 3.
*1 and *2: When float rod is in contact with stopper.Ohmmeter
Float position mm (in) Resistance valueΩ
(+) (−)
41*1 Full 24 (2.36) Approx. 5
*2 Empty 167 (6.57) Approx. 80
SKIA0904E
Ohmmeter
Float position mm (in) Resistance valueΩ
(+) (−)
13*1 Full 35 (1.50) Approx. 1
*2 Empty 186 (6.38) Approx. 40
SKIA1032E
Ohmmeter
Float position mm (in) Resistance valueΩ
(+) (−)
14*1 Full 24 (0.94) Approx. 5
*2 Empty 170 (6.69) Approx. 80
SKIA0909E
Ohmmeter
Float position mm (in) Resistance valueΩ
(+) (−)
13*1 Full 34 (1.34) Approx. 1
*2 Empty 186 (7.32) Approx. 40
SKIA0910E
Page 4064 of 4179
PG-62
HARNESS
F/FOG LT Front Fog Lamp
F/PUMP EC Fuel Pump
FIAR EC Fuel Injector Adjustment Resistor
FRO2 EC Front Heated Oxygen Sensor
FRO2/H EC Front Heated Oxygen Sensor Heater
FRPS EC Fuel Rail Pressure Sensor
FTP EC Fuel Transport Pump
FTS EC Fuel Temperature Sensor
FTS AT A/T Fluid Temperature Sensor Circuit
FUEL EC Fuel Injection System Function
GLORLY EC Glow Relay
GLOW EC Glow Control System
H/AIM LT Headlamp Aiming Control System
H/LAMP LT Headlamp
H/SEAT SE Heated Seat
HEATER MTC Heater System
HLC WW Headlamp Cleaner
HO2S1 EC Heated Oxygen Sensor 1
HO2S1H EC Heated Oxygen Sensor 1 Heater
HO2S2 EC Heated Oxygen Sensor 2
HO2S2H EC Heated Oxygen Sensor 2 Heater
HORN WW Horn
IATS EC Intake Air Temperature Sensor
IATSEN EC Intake Air Temperature Sensor
IGNSYS EC Ignition System
ILL LT Illumination
INJECT EC Injector
INJ/PW EC Fuel Injector Power Supply Circuit
INT/L LT Map Lamp
IVC EC Intake Valve Timing Control Solenoid Valve
KS EC Knock Sensor
LOAD EC Electrical Load Signal
LPSV AT Line Pressure Solenoid Valve
MAFS EC Mass Air Flow Sensor
MAIN AT Main Power Supply and Ground Circuit
MAIN EC Main Power Supply and Ground Circuit
METER DI Speedometer, Tachometer, Temp. and Fuel Gauges
MIL/DL EC MIL & Data Link Connector
MIRROR GW Door Mirror
MULTI BL Multi-Remote Control System
NATS BL Nissan Anti-Theft System
NAVI AV Navigation System
NONDTC AT Non-Detective Items
OVRCSV AT Overrun Clutch Solenoid ValveCode Section Wiring Diagram Name
Page 4092 of 4179
LT-14
HEADLAMP
Aiming Adjustment for HeadlampEKS003CG
When performing headlamp aiming adjustment, use an aiming machine, aiming wall screen or headlamp
tester. Aimers should be in good repair, calibrated and operated in accordance with respective operation man-
uals.
If any aimer is not available, aiming adjustment can be done as follows:
For details, refer to the regulations in your own country.
Keep all tires inflated to correct pressures.
Place vehicle and tester on one and same flat surface.
See that there is no-load in vehicle (coolant, engine oil filled up to correct level and full fuel tank) other
than the driver (or equivalent weight placed in driver's position).
CAUTION:
Be sure aiming switch is set to “0” when performing aiming adjustment.
LOW BEAM
1. Turn headlamp low beam on.
High beam indicator does not
work.1. Bulb
2. Grounds M27 and M70
3. Open in high beam circuit1. Check bulb in combination meter.
2. Check grounds M27 and M70.
3. Check the wire between lighting switch terminal 9 and
combination meter terminal 20 for an open circuit.
Driving lamp does not operate,
but high beam LH operates.1. 15A fuse
2. Open in driving lamp switch
3. Driving lamp switch circuit
4. Driving lamp relay-2
5. Open in driving lamp relay-2 circuit
6. Grounds E24 and E50
7. Driving lamp relay-1
8. Open in driving lamp relay-1 circuit
9. Open driving lamp circuit
10.Ground R8
11 . B u l b1. Check 15A fuse (No. 38, located in fuse and fusible
link box). Verify battery positive voltage is present at
terminal 3 of driving lamp relay-1.
2. Check the wire between lighting switch terminal 9 and
driving lamp switch terminal 7 for an open circuit.
3. Check driving lamp switch.
4. Check driving lamp relay-2.
5. Check the wire between driving switch terminal 4 and
driving lamp relay-2 terminal 1 for an open circuit.
Check the wire between driving switch terminal 6 and
driving lamp relay-2 terminal 3 for an open circuit.
Check the wire between lighting switch terminal 9 and
driving lamp relay-2 terminal 5 for an open circuit.
Check the wire between driving lamp relay-1 terminal
2 and driving lamp relay-2 terminal 7 for an open cir-
cuit.
6. Check grounds E24 and E50.
7. Check driving lamp relay-1.
8. Check the wire between lighting switch terminal 9 and
driving lamp relay-1 terminal 1 for an open circuit.
9. Check the wire between driving lamp relay-1 terminal
5 and driving lamp terminal 2 for an open circuit.
10.Check ground R8.
11.Check bulbs. Symptom Possible cause Repair order
PKIA5554E
Page 4093 of 4179
HEADLAMP
LT-15
C
D
E
F
G
H
I
J
L
MA
B
LT
2. Use adjusting screws to perform aiming adjustment.
First tighten the adjusting screw all the way and then make adjustment by loosening the screw.
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check
aiming. Use the aiming chart shown in the figure.
Adjust headlamps so that main axis of light is parallel to cen-
ter line of body and is aligned with point P shown in illustra-
tion.
Figure to the right shows headlamp aiming pattern for driving
on right side of road; for driving on left side of road, aiming
pattern is reversed.
Dotted lines to point P in illustration show center of head-
lamp.
Basic illuminating area for adjustment should be within the
range shown at right. Adjust headlamps accordingly.
CAUTION:
Be sure aiming switch is set to “0” when preforming aiming
adjustment.
Aiming Adjustment for Driving LampEKS00AP6
Turn the aiming adjusting screw to adjust.
For positions of the adjustment screws and direction to turn,
refer to the figures.
When adjusting for right or left side, adjust upper and lower
adjustment screws at the same time.
PREPARATION BEFORE ADJUSTING
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
1. Keep all tires inflated to correct pressures.
2. Place vehicle on level ground.
3. Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position),
coolant, engine oil filled up to correct level, full fuel tank and spare tire, jack, and tools."H" : Horizontal center line of headlamps
"W
L " : Distance between each headlamp center
"L" : 25,000mm (984.25 in)
"C" : 315mm (12.40 in) – 315mm(12.40in)+60mm
(2.36 in)
PKIA3537E
PKIA3394E
Page 4175 of 4179
IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Front Door Trim ................................................... EI-32
Front fog lamp .................................................... LT-52
Front passenger air bag .................................. SRS-35
Front seat .......................................................... SE-24
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner .... SB-2, SRS-3, SRS-40
Front side air bag ............................................. SRS-37
Front suspension ............................................... FSU-5
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FRPS - Wiring diagram .................... EC-999, EC-1309
FTS - Wiring diagram ...................... EC-994, EC-1304
FUEL - Wiring diagram ...................... EC-218, EC-225
Fuel check valve ................................ EC-473, EC-865
Fuel cut control (at no load high engine speed) EC-38,
EC-500
, EC-887, EC-1218
Fuel filler lid ...................................................... BL-103
Fuel filter .......................................... EC-890, EC-1221
Fuel filter replacement(QR20DEQR25DE) .......... FL-4
Fuel filter replacement(YD22DDTi) ....... FL-17, MA-31
Fuel gauge ............................................................ DI-4
Fuel injection control system ........... EC-885, EC-1216
Fuel injection system ......................... EC-216, EC-223
Fuel injector adjustment resistor .... EC-1115, EC-1404
Fuel injector and fuel tube(QR20DEQR25DE) . EM-32
Fuel injector and fuel tube(YD22DDTi) ............ EM-157
Fuel line inspection(QR20DEQR25DE) . FL-3, MA-23
Fuel line inspection(YD22DDTi) ............ FL-16, MA-31
Fuel pressure check ............................ EC-48, EC-510
Fuel pressure release .......................... EC-48, EC-510
Fuel pump .......... EC-443, EC-835, EC-890, EC-1127,
EC-1416
Fuel pump and gauge(QR20DEQR25DE) .......... FL-4
Fuel rail pressure sensor ................. EC-997, EC-1307
Fuel system(QR20DEQR25DE) .......................... FL-3
Fuel system(YD22DDTi) ..................................... FL-16
Fuel tank(QR20DEQR25DE) ............................ FL-11
Fuel tank(YD22DDTi) ......................................... FL-23
Fuel temperature sensor ................. EC-993, EC-1303
Fuse ................................................................... PG-12
Fuse and fusible link box ................................... PG-76
Fusible link ......................................................... PG-12
G
Gauges ................................................................. DI-4
Gear components (M/T) ....................... MT-20, MT-25
Generator .......................................................... SC-12
Generator - See Alternator ................................ SC-12
Generic scan tool (GST) .................... EC-112, EC-931
Glass .................................................. GW-80, GW-83
GLOW - Wiring diagram EC-1070, EC-1170, EC-1458
Glow plug ....................................... EC-1169, EC-1457
Glow plug(YD22DDTi) ..................................... EM-152
Glow relay ...................... EC-1069, EC-1169, EC-1457
GPS antenna ..................................................... AV-43
Grille - See Exterior ............................................. EI-19
Ground distribution ............................................ PG-13
H
H/AIM - Wiring diagram ...................................... LT-29
H/LAMP - Wiring diagram ........................... LT-4, LT-7
H/MIRROR - Wiring diagram ............................ GW-21
Harness connector ............................................. PG-70
Harness layout ................................................... PG-30
Headlamp ............................................................. LT-4
Headlamp aiming control .................................... LT-29
Headlamp leveler - See Headlamp aiming control .......
LT-29
Headlamp washer ............................................ WW-20
Headlining - See Roof trim .................................. EI-39
Heated oxygen sensor 1 .... EC-176, EC-183, EC-193,
EC-318
, EC-324, EC-611, EC-618, EC-786
Heated oxygen sensor 1 heater ......... EC-138, EC-771
Heated oxygen sensor 2 .... EC-201, EC-208, EC-330,
EC-338
, EC-792
Heated oxygen sensor 2 heater ......... EC-144, EC-776
Heated seat ........................................... SE-18, SE-21
HEATER - Wiring diagram ................................ MTC-6
Heater and cooling unit (Heater core) ............ ATC-131
Heater mirror ..................................................... GW-21
Heater system - Wiring diagram ....................... MTC-6
Heater unit (heater core) .. ATC-136, MTC-27, MTC-30
HFC134a (R134a) system precaution ............... ATC-4
HFC134a (R134a) system service procedure ATC-141
HFC134a (R134a) system service tools .......... ATC-15
HFC134a system service equipment precaution ..........
ATC-10
HO2S1 - Wiring diaram ...... EC-178, EC-186, EC-196,
EC-613
, EC-620
HO2S1H - Wiring diagram ............................... EC-140
HO2S2 - Wiring diagram .... EC-203, EC-211, EC-333,
EC-341
HO2S2H - Wiring diagram ............................... EC-146
Hood .................................................................. BL-12
Horn ................................................................. WW-25
HORN - Wiring diagram ................................... WW-25
How to erase DTC ........................... EC-514, EC-1223
How to erase DTC for OBD system ..... EC-63, EC-895
I
IATS - Wiring diagram ...... EC-158
, EC-977, EC-1287
IATSEN - Wiring diagram ................................ EC-782
Identification ...................................... ATC-12, ATC-13
Idle air volume learning ........................ EC-46, EC-508
Idle speed ............. EC-79, EC-526, EC-905, EC-1231
Ignition coil ......................................... EC-417, EC-798
Ignition coil(QR20DEQR25DE) ....................... EM-29
Ignition control system ....................... EC-417, EC-798
Ignition timing ....................................... EC-79, EC-526
IGNSYS - Wiring diagram .................. EC-418, EC-799
ILL - Wiring diagram ........................................... LT-66
Illumination .......................................................... LT-66
In vehicle sensor ........... ATC-111, ATC-113, ATC-122
INJE/PW - Wiring diagram ............. EC-1158, EC-1446
INJECT - Wiring diagram . EC-429, EC-821, EC-1008,
Page 4176 of 4179
IDX-6
ALPHABETICAL INDEX
EC-1124, EC-1163, EC-1317, EC-1413, EC-1451
Injection nozzle(YD22DDTi) ........................... EM-157
Injector ............................................... EC-428, EC-820
Input shaft (FF M/T) .............................. MT-20, MT-25
Intake air temperature sensor ........... EC-156, EC-781,
EC-976
, EC-1286
Intake door control linkage adjustment ............ ATC-81
Intake door motor ATC-79, ATC-128, MTC-11, MTC-26
Intake manifold(QR20DEQR25DE) ................. EM-17
Intake manifold(YD22DDTi) ............................ EM-136
Intake sensor ................................................. ATC-117
Intake valve timing control ................. EC-135, EC-582
Intake valve timing control solenoid valve ....... EC-286
Interior ....................... EI-32, EI-34, EI-35, EI-38, EI-39
Interior lamp ........................................................ LT-76
Interior lamp on-off control ...................... LT-76, LT-77
ISO 15031-5 Mode 1 - 9 ...................... EC-51, EC-892
IVC - Wiring diagram ....................................... EC-287
J
Joint connector (J/C) .......................................... PG-75
K
Keyless entry system - See Multi-remote control system
BL-74
Knock sensor (KS) ............................. EC-242, EC-633
KS - Wiring diagram ........................... EC-243, EC-634
L
LAN system circuit ........................................... ATC-69
License lamp ....................................................... LT-47
Line pressure test (A/T) ....................... AT-68, AT-260
Liquid gasket application ......................... LU-3, LU-17
Liquid gasket application(QR20DEQR25DE) ... EM-6,
EM-123
, CO-3, CO-25
LOAD - Wiring diagram ...................... EC-457, EC-849
Location of electrical units ................................. PG-65
Lock, door ............................................... BL-91, BL-95
Lubricant (R134a) A/C ........................ ATC-5, ATC-24
Lubrication circuit (engine)(QR20DEQR25DE) .. LU-5
Lubrication circuit (engine)(YD22DDTi) ............. LU-19
Lubrication oil A/C .......................................... ATC-164
Lubrication-locks, hinges and hood latches ...... MA-45
M
M/T major overhaul ............................... MT-28
, MT-37
M/T oil replacement ........................................... MT-11
M/T removal and installation .............................. MT-17
MAFS - Wiring diagram ..... EC-151, EC-592, EC-965,
EC-972
, EC-1282
Magnet clutch ................................. ATC-88, ATC-146
MAIN - Wiring diagram ...... EC-124, EC-571, EC-938,
EC-1262
Mainshaft (M/T) ..................................... MT-20, MT-25
Maintenance (engine)(YD22DDTi) ................... MA-27
Major overhaul (Transfer) .................................. TF-57
Malfunction indicator (MI) .... EC-64, EC-516, EC-896,
EC-1224
Mass air flow sensor (MAFS) ........... EC-149, EC-590,
EC-963
, EC-970, EC-1280
Master cylinder (brake) ...................................... BR-14
Master cylinder (clutch) ........................................ CL-8
Meter ..................................................................... DI-4
METER - Wiring diagram ......................... DI-14, DI-17
MIL/DL - Wiring diagram ............... EC-1202, EC-1498
MIRROR - Wiring diagram ............................... GW-87
Mirror defogger ................................................ GW-21
Mirror, door ...................................................... GW-86
Mirror, out side ................................................. GW-86
Misfire .............................................................. EC-237
Mode door control linkage adjustment ........... ATC-75,
ATC-134
, MTC-9, MTC-31
Mode door motor ............................ ATC-73, ATC-134
Molding - See Exterior ................... EI-22, EI-24, EI-25
Mud guard - See Exterior .................................... EI-24
MULTI - Wiring diagram ..................................... BL-77
Multiport fuel injection (MFI) system ... EC-34, EC-496
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system ............................... BL-74
N
NATS - Wiring diagram .................................... BL-111
NATS (Nissan anti-theft system) ..................... BL-108
NATS (Nissan anti-theft system) precautions ....... GI-3
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (Transfer) ........................... TF-8
O
Oil cooler (engine)(QR20DEQR25DE) ............. LU-11
Oil cooler (engine)(YD22DDTi) .......................... LU-28
Oil filter(QR20DEQR25DE) .............................. LU-10
Oil filter(YD22DDTi) ........................................... LU-23
Oil pan (engine)(QR20DEQR25DE) ................ EM-25
Oil pan (engine)(YD22DDTi) ........................... EM-147
Oil pressure (engine)(QR20DEQR25DE) ........... LU-7
Oil pressure (engine)(YD22DDTi) ...................... LU-20
Oil pump (engine)(QR20DEQR25DE) .............. LU-13
Oil pump (engine)(YD22DDTi) ........................... LU-30
Oil seal replacement (engine)(QR20DEQR25DE) ......
EM-44
, EM-67, EM-82
On board diagnostic system . EC-51, EC-513, EC-892
Operating cylinder (clutch) ................................. CL-10
Out side mirror ................................................. GW-86
Overdrive control switch .................... AT-240, AT-327
Overheat ........... EC-348, EC-700, EC-1011, EC-1320
Oversize piston(QR20DEQR25DE) ............... EM-104
Oversize piston(YD22DDTi) ........................... EM-230
P
Park/Neutral position switch EC-373
, EC-725, EC-816,
EC-1182
, EC-1479