fuse diagram NISSAN X-TRAIL 2005 Service Service Manual

TROUBLE DIAGNOSES FOR SYMPTOMS
AT-291
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
MA
B
AT

O/D OFF Indicator Lamp Does Not Come OnECS00EBE
SYMPTOM:
O/D OFF indicator lamp does not come on for about 2 seconds
when turning ignition switch to “ON”.
1. CHECK TCM POWER SOURCE
1. Turn ignition switch to ON. (Do not start engine.)
2. Check voltage between TCM connector terminals 10, 19, 28 and ground.
3. Turn ignition switch to OFF.
4. Check voltage between TCM connector terminal 28 and ground.
OK or NG
OK >> GO TO 2.
NG >> Check the following items:

Harness for short or open between ignition switch and
TCM connector terminals 10, 19 and 28

Refer to AT- 3 9 5 , "Wiring Diagram — AT — MAIN" .

Ignition switch and fuse Refer to PG-2, "POWER SUPPLY ROUTING" .
2. CHECK TCM GROUND CIRCUIT
1. Turn ignition switch to OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM connector terminals 25, 48 and
ground.
If OK, check harness for short to ground and short to power.
OK or NG
OK >> GO TO 3.
NG >> Repair open circuit or short to ground or short to power
in harness or connectors. Refer to AT- 3 9 5 , "
Wiring Dia-
gram — AT — MAIN" .
3. CHECK COMBINATION METERS SYSTEM
Check combination meters system. Refer to DI-14, "
Combination Meter" .
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
SCIA4281E
Voltage: Battery voltage
Voltage: Battery voltage
SCIA0713E
Continuity should exist.
SCIA0766E

AT-338
[ALL]
VEHICLE SPEED SENSOR·A/T (REVOLUTION SENSOR)

6. CHECK HARNESS BETWEEN TCM AND REVOLUTION SENSOR (POWER)
1. Turn ignition switch OFF.
2. Disconnect the TCM connector and revolution sensor harness connector.
3. Check continuity between TCM connector and revolution sensor
harness connector. Refer to AT- 2 1 , "
Circuit Diagram" and AT-
395, "Wiring Diagram — AT — MAIN" .
4. If OK, check harness for short to ground and short power.
5. Reinstall any part removed.
OK or NG
OK >> Fuse or ignition switch are malfunctioning.
NG >> Repair open circuit or short to ground or short to power in harness or connectors.
7. CHECK HARNESS BETWEEN TCM AND REVOLUTION SENSOR (SENSOR GROUND)
1. Turn ignition switch OFF.
2. Disconnect the TCM connector and revolution sensor harness connector.
3. Check continuity between TCM connector and revolution sensor
harness connector.
4. If OK, check harness for short to ground and short power.
5. Reinstall any part removed.
OK or NG
OK >> GO TO 5.
NG >> Repair open circuit or short to ground or short to power in harness or connectors.
8. CHECK DTC
Perform AT- 3 3 2 , "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 5.
Item Connector No. Terminal No.
(Wire color) Continuity
TCM F46 10 (BR/W)
Ye s
Revolution sensor F15 1 (Y)
Item Connector No. Terminal No.
(Wire color) Continuity
TCM F46 19 (BR/W)
Ye s
Revolution sensor F15 1 (Y)
SCIA2617E
Item Connector No. Terminal No.
(Wire color) Continuity
TCM F47 42 (B)
Ye s
Revolution sensor F15 3 (B)
SCIA2618E

SRS-8
TROUBLE DIAGNOSIS

TROUBLE DIAGNOSISPFP:00004
Trouble Diagnosis IntroductionEHS000CL
CAUTION:

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harness can be identified by yellow and/or orange harnesses or har-
ness connector.

Do not attempt to repair, splice or modify the SRS wiring harness. If the harness is damaged,
replace it with a new one.

Keep ground portion clean.
DIAGNOSIS FUNCTION
The SRS self-diagnosis results can be read by using “AIR BAG” warning lamp and/or CONSULT-II.
The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a system mal-
function through the operation of the “AIR BAG” warning lamp.
The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the “AIR BAG” warning lamp and CONSULT-II are as follows:
NOTE:
Seat belt pre-tensioner malfunction is indicated by “AIR BAG” warning lamp.
HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp-
toms or conditions for a customer complaint.
Information From Customer
WHAT..... Vehicle model
WHEN..... Date, Frequencies
WHERE..... Road conditions
HOW..... Operating conditions, Symptoms
Preliminary Check
Check that the following parts are in good order.

Battery (Refer to SC-4, "How to Handle Battery" .)

Fuse (Refer to SRS-11, "Wiring Diagram — SRS — /LHD models" or SRS-13, "Wiring Diagram — SRS
— /RHD models" .)

System component-to-harness connections
User mode Diagnosis mode Display type
“AIR BAG” warning lamp X X ON-OFF operation
CONSULT-II — X Monitoring

NATS (NISSAN ANTI-THEFT SYSTEM)
BL-121
C
D
E
F
G
H
J
K
L
MA
B
BL

SYMPTOM MATRIX CHART 2
Non self-diagnosis related item
DIAGNOSTIC SYSTEM DIAGRAM
Diagnostic Procedure 1EIS008F6
Self-diagnostic results:
“ECM INT CIRC-IMMU” displayed on CONSULT-II screen
1. Confirm SELF-DIAGNOSTIC RESULTS “ECM INT CIRC-IMMU”
displayed on CONSULT-II screen. Ref. part No. B.
2. Replace ECM.
3. Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II operation manual NATS”.
SYMPTOMDIAGNOSTIC PROCEDURE
(Reference page)SYSTEM
(Malfunctioning part or mode)REFERENCE PART NO. OF
ILLUSTRATION ON SYSTEM
DIAGRAM
Security Ind. does not light up.PROCEDURE 6
(BL-128
)Security Ind. —
Open circuit between Fuse and
IMMU—
Continuation of initialization
mode—
IMMU A
Security Ind. does not blink just
after initialization even if the
vehicle is equipped with don-
gle unit.
PROCEDURE 8
(BL-130
)NATS might be initialized with-
out connecting dongle unit
properly.—
Open circuit in ground line of
dongle unit circuitC6
Security Ind. does not blink just
after ignition switch is turned to
ON when some malfunction
related to NATS is detected
even if the vehicle is equipped
with dongle unit.Open or short circuit in commu-
nication line between IMMU
and dongle unitC5
Dongle unit G
SEL028X
SEL152X

PG-1
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION PG
A
B
PG

POWER SUPPLY, GROUND & CIRCUIT ELEMENTS
POWER SUPPLY ROUTING ...................................... 2
Schematic ................................................................ 2
Wiring Diagram — POWER — ................................. 3
BATTERY POWER SUPPLY — IGNITION SW.
IN ANY POSITION ................................................ 3
ACCESSORY POWER SUPPLY — IGNITION
SW. IN “ACC” OR “ON” ......................................... 7
IGNITION POWER SUPPLY — IGNITION SW.
IN “ON” AND/OR “START” .................................... 8
Fuse ....................................................................... 12
Fusible Link ............................................................ 12
Circuit Breaker ....................................................... 12
GROUND .................................................................. 13
Ground Distribution ................................................ 13
MAIN HARNESS/LHD MODELS ........................ 13
MAIN HARNESS/RHD MODELS ........................ 16
ENGINE ROOM HARNESS/LHD MODELS ....... 19
ENGINE ROOM HARNESS/RHD MODELS ....... 21
ENGINE ROOM HARNESS ................................ 23
ENGINE CONTROL HARNESS/GASOLINE
ENGINE MODELS .............................................. 24
ENGINE CONTROL HARNESS/DIESEL
ENGINE MODELS .............................................. 25
BODY HARNESS/LHD MODELS ....................... 26
BODY HARNESS/RHD MODELS ....................... 27
BODY NO. 2 HARNESS/LHD MODELS ............. 28
BODY NO. 2 HARNESS/RHD MODELS ............ 29
ROOM LAMP HARNESS .................................... 30
BACK DOOR SUB HARNESS/REAR WINDOW
DEFOGGER HARNESS ..................................... 31
HARNESS ................................................................. 32
Harness Layout ...................................................... 32
HOW TO READ HARNESS LAYOUTS ............... 32
OUTLINE/LHD MODELS .................................... 33
OUTLINE/RHD MODELS .................................... 34
MAIN HARNESS/LHD MODELS ........................ 35MAIN HARNESS/RHD MODELS ........................ 37
ENGINE ROOM HARNESS/LHD MODELS ........ 39
ENGINE ROOM HARNESS/RHD MODELS ....... 45
ENGINE CONTROL HARNESS .......................... 51
BODY HARNESS/LHD MODELS ....................... 56
BODY HARNESS/RHD MODELS ....................... 57
BODY NO. 2 HARNESS/LHD MODELS ............. 58
BODY NO. 2 HARNESS/RHD MODELS ............. 59
ROOM LAMP HARNESS .................................... 60
FRONT DOOR HARNESS/LHD MODELS .......... 61
FRONT DOOR HARNESS/RHD MODELS ......... 62
REAR DOOR HARNESS .................................... 63
BACK DOOR HARNESS .................................... 64
Wiring Diagram Codes (Cell Codes) ...................... 65
ELECTRICAL UNITS LOCATION ............................ 69
Electrical Units Location ......................................... 69
ENGINE COMPARTMENT .................................. 69
PASSENGER COMPARTMENT/LHD MODELS ... 70
PASSENGER COMPARTMENT/RHD MODELS ... 72
HARNESS CONNECTOR ......................................... 74
Description .............................................................. 74
HARNESS CONNECTOR (TAB-LOCKING
TYPE) .................................................................. 74
HARNESS CONNECTOR (SLIDE-LOCKING
TYPE) .................................................................. 75
ELECTRICAL UNITS ................................................ 76
Terminal Arrangement ............................................ 76
STANDARDIZED RELAY .......................................... 77
Description .............................................................. 77
NORMAL OPEN, NORMAL CLOSED AND
MIXED TYPE RELAYS ........................................ 77
TYPE OF STANDARDIZED RELAYS ................. 77
FUSE BLOCK - JUNCTION BOX (J/B) .................... 79
Terminal Arrangement ............................................ 79
FUSE AND FUSIBLE LINK BOX .............................. 80
Terminal Arrangement ............................................ 80

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Fork rod (M/T) ....................................... MT-25, MT-43
Freeze frame data EC-56, EC-566, EC-999, EC-1373
FRO2 - Wiring diagram ...................... EC-847, EC-862
Front bumper ....................................................... EI-14
Front disc brake ................................................. BR-27
Front door ........................................................... BL-18
Front Door Trim ................................................... EI-32
Front fog lamp .................................................. LT-108
Front passenger air bag .................................. SRS-35
Front seat .......................................................... SE-24
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner .... SB-2, SRS-3, SRS-40
Front side air bag ............................................. SRS-37
Front suspension ............................................... FSU-5
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FRPS - Wiring diagram .................. EC-1111, EC-1467
FTS - Wiring diagram .................... EC-1107, EC-1463
FUEL - Wiring diagram ...................... EC-221, EC-227
Fuel check valve ................................ EC-522, EC-962
Fuel cut control (at no load high engine speed) EC-38,
EC-551
, EC-988, EC-1364
Fuel filler lid ...................................................... BL-103
Fuel filter .......................................... EC-994, EC-1370
Fuel filter replacement(QR20DE-QR25DE) .......... FL-4
Fuel filter replacement(YD22DDTi) ....... FL-17, MA-34
Fuel gauge ............................................................ DI-4
Fuel injection control system ........... EC-986, EC-1362
Fuel injection system ......................... EC-219, EC-225
Fuel injector adjustment resistor .... EC-1251, EC-1590
Fuel injector and fuel tube(QR20DE-QR25DE) . EM-34
Fuel injector and fuel tube(YD22DDTi) ............ EM-167
Fuel line inspection(QR20DE-QR25DE) . FL-3, MA-24
Fuel line inspection(YD22DDTi) ............ FL-16, MA-34
Fuel pressure check ............................ EC-49, EC-562
Fuel pressure release .......................... EC-49, EC-562
Fuel pump .......... EC-466, EC-906, EC-994, EC-1263,
EC-1602
Fuel pump and gauge(QR20DE-QR25DE) .......... FL-4
Fuel rail pressure sensor ............... EC-1110, EC-1466
Fuel system(QR20DE-QR25DE) .......................... FL-3
Fuel system(YD22DDTi) ..................................... FL-16
Fuel tank(QR20DE-QR25DE) ............................ FL-11
Fuel tank(YD22DDTi) ......................................... FL-23
Fuel temperature sensor ............... EC-1106, EC-1462
Fuse ................................................................... PG-12
Fuse and fusible link box ................................... PG-80
Fusible link ......................................................... PG-12
G
Gauges ................................................................. DI-4
Gear components (M/T) ....................... MT-23, MT-41
Generator .......................................................... SC-13
Generator - See Alternator ................................ SC-13
Generic scan tool (GST) .................. EC-113, EC-1040
Glass .................................................. GW-80, GW-83
GLOW - Wiring diagram EC-1183, EC-1306, EC-1644
Glow plug ....................................... EC-1305, EC-1643
Glow plug(YD22DDTi) .................................... EM-162
Glow relay ..................... EC-1182, EC-1305, EC-1643
Grille - See Exterior ............................................ EI-19
Ground distribution ............................................ PG-13
H
H/LAMP - Wiring diagram ......................... LT-9
, LT-28
H/MIRROR - Wiring diagram ............................ GW-21
Harness connector ............................................. PG-74
Harness layout ................................................... PG-32
Headlamp ............................................................. LT-5
Headlamp aiming control .................................... LT-66
Headlamp washer ............................................ WW-20
Headlining - See Roof trim .................................. EI-39
Heated oxygen sensor 1 .... EC-179, EC-186, EC-196,
EC-322
, EC-328, EC-666, EC-673, EC-861
Heated oxygen sensor 1 heater ......... EC-139, EC-846
Heated oxygen sensor 2 .... EC-204, EC-211, EC-334,
EC-342
, EC-867
Heated oxygen sensor 2 heater ......... EC-145, EC-851
Heated seat ........................................... SE-18, SE-21
HEATER - Wiring diagram ................................ MTC-6
Heater and cooling unit (Heater core) ............ ATC-131
Heater mirror ..................................................... GW-21
Heater system - Wiring diagram ....................... MTC-6
Heater unit (heater core) .. ATC-136, MTC-27, MTC-30
HFC134a (R134a) system precaution ............... ATC-4
HFC134a (R134a) system service procedure ATC-141
HFC134a (R134a) system service tools .......... ATC-15
HFC134a system service equipment precaution ..........
ATC-10
HO2S1 - Wiring diaram ...... EC-181, EC-189, EC-199,
EC-668
, EC-675
HO2S1H - Wiring diagram ............................... EC-141
HO2S2 - Wiring diagram .... EC-206, EC-214, EC-337,
EC-345
HO2S2H - Wiring diagram ............................... EC-147
Hood .................................................................. BL-12
Horn ................................................................. WW-27
HORN - Wiring diagram ................................... WW-27
How to erase DTC ........................... EC-566, EC-1372
How to erase DTC for OBD system ..... EC-63, EC-999
I
IATS - Wiring diagram .... EC-161
, EC-1089, EC-1445
IATSEN - Wiring diagram ................................ EC-857
Identification ...................................... ATC-12, ATC-13
Idle air volume learning ........................ EC-47, EC-560
Idle speed ........... EC-79, EC-578, EC-1012, EC-1382
Ignition coil ......................................... EC-440, EC-873
Ignition coil(QR20DE-QR25DE) ....................... EM-31
Ignition control system ....................... EC-440, EC-873
Ignition timing ....................................... EC-79, EC-578
IGNSYS - Wiring diagram .................. EC-441, EC-874
ILL - Wiring diagram ......................................... LT-122
Illumination ........................................................ LT-122
In vehicle sensor ........... ATC-111, ATC-113, ATC-122