turn signal NISSAN X-TRAIL 2005 Service Repair Manual

LT-94
TURN SIGNAL AND HAZARD WARNING LAMPS

Bulb ReplacementEKS0034D
FRONT TURN SIGNAL LAMP
1. Remove the front turn signal lamp. Refer to LT- 9 4 , "Removal
and Installation of Front Turn Signal Lamp"
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
4. Installation is the reverse order of removal.
SIDE TURN SIGNAL LAMP
1. Remove side turn signal lamp. Refer to LT- 9 5 , "Removal and
Installation of Side Turn Signal Lamp"
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
4. Installation is the reverse order of removal.
REAR TURN SIGNAL LAMP
Refer to LT- 11 9 , "Bulb Replacement" in “REAR COMBINATION LAMP”.
Removal and Installation of Front Turn Signal LampEKS003BH
REMOVAL
1. Press the upper pawl to remove front turn signal lamp forward
the front of the vehicle.
2. Disconnect front turn signal lamp connector.
INSTALLATION
1. Connect front turn signal lamp connector.
2. Insert the pawl into head lamp hole, and install front turn signal lamp.Front turn signal lamp : 12V - 21W (amber)
SKIA0053E
Side turn signal lamp : 12V - 5W
PKIA0468E
SKIA0054E

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-95
C
D
E
F
G
H
I
J
L
MA
B
LT

Removal and Installation of Side Turn Signal LampEKS003BI
REMOVAL
1. Push the side turn signal lamp toward A direction in the figure,
and pull up B direction in the figure.
2. Disconnect the side turn signal lamp connector.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Rear Turn Signal LampEKS003BJ
Refer to LT- 11 9 , "Removal and Installation" in “REAR COMBINATION LAMP”.
PKIA0469E

LT-96
LIGHTING AND TURN SIGNAL SWITCH

LIGHTING AND TURN SIGNAL SWITCHPFP:25540
Removal and InstallationEKS0034F
REMOVAL
1. Remove the steering column cover. Refer to IP-10, "INSTRU-
MENT PANEL ASSEMBLY" in “INSTRUMENT PANEL (IP)”
section.
2. Remove two screws, then remove the lighting and turn signal
switch from the spiral cable.
3. Disconnect the lighting and turn signal switch connector.
INSTALLATION
Installation is the reverse order of removal.
Switch Circuit InspectionEKS0034G
Using circuit tester, check continuity between the lighting and turn signal switch connector terminals in each
operation status of the switch.
Lighting switch is refer to LT- 2 8 , "
Wiring Diagram — H/LAMP —" .
Turn signal lamp switch is refer to LT- 8 9 , "
Wiring Diagram — TURN —" .
Front fog lamp switch is refer to LT- 1 0 9 , "
Wiring Diagram — F/FOG —" .
Rear fog lamp switch is refer to LT- 11 3 , "
Wiring Diagram — R/FOG —/Without Front Fog Lamp" ,LT- 11 4 , "Wir-
ing Diagram — R/FOG —/With Front Fog Lamp" .
SKIA0018E

REAR COMBINATION LAMP
LT-119
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS00164
1. Remove rear combination lamp mounting bolts.
2. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins.
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb.
5. Installation is the reverse order of removal.
Removal and InstallationEKS00165
REMOVAL
1. Remove luggage-side lower finisher. Refer to EI-35, "BODY
SIDE TRIM" in “EI EXTERIOR & INTERIOR” section.
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts.
4. Pull rear combination lamp rearward the vehicle. Disengage
locating pins.
5. Pull harness grommet and remove harness.
INSTALLATION
Installation is the reverse order of removal.Stop/tail lamp : 12V - 21/5W
Rear turn signal lamp : 12V - 21W
Back-up lamp : 12V - 21W
PKIC0923E
PKIA8620E
Rear combination lamp mounting bolts
: 5.4 N·m (0.55 kg-m, 48 in-lb)

LT-120
COMBINATION SWITCH

COMBINATION SWITCHPFP:25567
Removal and InstallationEKS001V6
Refer to SRS-33, "SPIRAL CABLE" in “SUPPLEMENTAL RESTRAINT SYSTEM (SRS)” section.
Switch Circuit InspectionEKS001V7
Refer to LT- 9 6 , "Switch Circuit Inspection" in “LIGHTING AND TURN SIGNAL SWITCH”, and WW-8, "Te r m i -
nal and Reference Values for Combination Switch" , WW-16, "Terminal and Reference Values for Combination
Switch" in “Wiper, Washer&Horn (WW)” section.

INTERIOR ROOM LAMP
LT-133
C
D
E
F
G
H
I
J
L
MA
B
LT

When map lamp switch is ON, ground is supplied (with sunroof)

to map lamp terminal 2

through ground M27 and M70.
INTERIOR ROOM LAMP TIMER OPERATION
When interior room lamp and map lamp (with sunroof) switch is in the DOOR position, the time control unit
keeps the interior room lamp and map lamp (with sunroof) illuminated for about 30 seconds when

unlock signal is supplied from driver's door unlock sensor while all doors are closed and key is out of igni-
tion key cylinder

key is removed from ignition key cylinder while all doors are closed

driver's door is opened and then closed while key is out of the ignition key cylinder. (However, if the
driver's door is closed with the key inserted in the ignition key cylinder after the driver's door is opened
with the key removed, the timer is operated.)
The timer is canceled when

driver's door is locked,

driver's door is opened, or

ignition switch is turned ON.
ON-OFF CONTROL
When the driver’s door, passenger’s door, rear LH door or rear RH door is opened, the interior room lamp and
map lamp (with sunroof) turns on while the interior room lamp and map lamp (with sunroof) switch is in the
DOOR position.

LT-138
INTERIOR ROOM LAMP

Interior Room Lamp Timer Does Not OperateEKS00OM7
1. CHECK POWER SUPPLY SIGNAL
1. Turn ignition switch OFF.
2. Disconnect time control unit connector.
3. Check voltage between time control unit harness connector and
ground.
OK or NG
OK >> GO TO 2.
NG >> Check the following.

10A fuse [No. 28, located in fuse block (J/B)]

Harness for open or short between time control unit and 10A fuse (No. 28)
2. CHECK FRONT DOOR SWITCH (DRIVER SIDE) INPUT SIGNAL
1. Connect time control unit connector.
2. Check voltage between time control unit harness connector and
ground.
OK or NG
OK >> GO TO 4.
NG >> GO TO 3.
3. CHECK FRONT DOOR SWITCH (DRIVER SIDE)
1. Disconnect front door switch (driver side) connector.
2. Check continuity between front door switch (driver side) termi-
nals.
OK or NG
OK >> Check the following.

Front door switch (driver side) ground circuit condition

Harness for open or short between time control unit and front door switch (driver side)
NG >> Replace front door switch (driver side).
Te r m i n a l
Voltage (+)
(−)
Connector Terminal (Wire color)
M30 1 (L) Ground Battery voltage
PKIA5561E
Terminal
Condition Voltage (+)
(−)
Connector Terminal (Wire color)
M31 30 (SB) GroundOFF (closed) Approx. 5V
ON (open) Approx. 0V
PKIA5562E
Connector Terminal Condition Continuity
B16 2 3Pushed (closed) No
Released (open) Yes
PKIC0928E

INTERIOR ROOM LAMP
LT-141
C
D
E
F
G
H
I
J
L
MA
B
LT

8. CHECK KEY SWITCH INPUT SIGNAL
Check voltage between time control unit harness connector and
ground.
OK or NG
OK >> Replace time control unit.
NG >> GO TO 9.
9. CHECK KEY SWITCH
1. Disconnect key switch connector.
2. Check continuity between key switch terminals.
OK or NG
OK >> Check the following.

Harness for open or short between key switch and
10A fuse (No. 28)

Harness for open or short between time control unit and key switch
NG >> Replace key switch.
Interior Room Lamp Timer Does Not CancelEKS00OM8
1. CHECK IGNITION ON SIGNAL
1. Turn ignition switch OFF.
2. Disconnect time control unit connector.
3. Check voltage between time control unit harness connector and
ground.
OK or NG
OK >> GO TO 2.
NG >> Check the following.

10A fuse [No. 5, located in fuse block (J/B)]

Harness for open or short between time control unit and 10A fuse (No. 5)
Terminal
Condition Voltage (+)
(−)
Connector Terminal (Wire color)
M31 18 (W/L) GroundInserted Battery voltage
Removed Approx. 0V
PKIA5568E
Connector Terminal Condition Continuity
M9 1 2Inserted Yes
Removed No
PKIA5569E
Terminal Ignition switch position
(+)
(−)OFFACCON
ConnectorTe r m i n a l
(Wire color)
M31 17 (G) Ground Approx. 0V Approx. 0VBattery
voltage
PKIA5570E

LT-152
BULB SPECIFICATIONS

BULB SPECIFICATIONSPFP:26297
HeadlampEKS003GS
Exterior LampEKS003GT
Interior Lamp/IlluminationEKS003GU
Item Wattage (W)
Xenon typeLow 35 (D2R)
High 55 (H1)
Conventional type High/Low 60/55 (H4)
Driving lamp65 (H1R1)
Item Wattage (W)
Front combination lamp Clearance lamp 5
Front turn signal lamp21 (amber)
Side turn signal lamp5
Fog lampFront fog lamp 55 (H11)
Rear fog lamp 21
Rear combination lampStop/Tail lamp 21/5
Rear turn signal lamp 21
Back-up lamp 21
License plate lamp5
High-mounted stop lamp5
Item Wattage (W)
Interior room lamp10
Map lampWithout sunroof 8
With sunroof 10
Luggage room lamp10
Ste p lamp2.7
Ashtray illumination lamp1.4

COMBINATION METERS
DI-5
C
D
E
F
G
H
I
J
L
MA
B
DI

TACHOMETER
The tachometer indicates engine speed in revolutions per minute (rpm).
ECM provides an engine speed signal to combination meter for tachometer with CAN communication line.
SPEEDOMETER
ESP/TCS/ABS control unit (with ESP) or ABS actuator and electric unit (without ESP) provides a vehicle
speed signal to the combination meter for the speedometer with CAN communication line.
FUEL GAUGE
The fuel gauge indicates the approximate fuel level in the fuel tank.
The fuel gauge is regulated by a variable ground signal supplied

from grounds B8 and B18 (LHD models)

from grounds B107 and B119 (RHD models)

through terminal 1 and 4 of the fuel level sensor unit

through terminal 3 and 1 of the sub fuel level sensor unit and

to combination meter terminal 8 for the fuel gauge.
AMBIENT TEMPERATURE INDICATOR
The ambient temperature is indicated by the signal from ambient sensor.
Combination meter inputs voltage conversed from resistance which ambient sensor detects.
Indication range is between −30 and 55 °C (−22 and 131 °F). When ambient air temperature is less than −30
°C (−22 °F) or more than 55 °C (131 °F), display shows “---°C”. When indicated temperature becomes less
than 3 °C (37 °F), ambient temperature indicator flashes as a sign of warning.
Without Auto A/C
Power is supplied

through combination meter terminal 27

to ambient sensor terminal 1.
Ground is supplied

to combination meter terminal 28

through ambient sensor terminal 2.
Signal is supplied

through ambient sensor terminal 1

to combination meter terminal 27.
With Auto A/C
Power is supplied

through auto amp terminal 9

to ambient sensor terminal 1.
Ground is supplied

to combination meter terminal 28 and auto amp terminal 24

through ambient sensor terminal 2.
And combination meter receives ambient sensor signal from ambient sensor

through ambient sensor terminal 1

to combination meter terminal 27.
NOTE:
Combination meter distinguishes whether or not the combination meter terminal 29 receives voltage (auto A/C
recognition signal) from auto amp terminal 28. If the terminal receives, combination meter discerns as auto A/
C.
Indication When Turning Ignition Switch OFF

In a case that temperature detected by ambient sensor is higher than indicated temperature before turn-
ing ignition switch OFF.
–In a case of more than 3.5 hours after turning ignition switch OFF, temperature detected by ambient sen-
sor is indicated when turning ignition switch ON.