four wheel drive NISSAN X-TRAIL 2006 Owners Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2006, Model line: X-TRAIL, Model: NISSAN X-TRAIL 2006Pages: 281, PDF Size: 3.26 MB
Page 72 of 281
oil” in the “8. Maintenance and do-it-yourself”
section.
CAUTION
Running the engine with the oil pres-
sure warning light on could cause seri-
ous damage to the engine almost imme-
diately. Turn off the engine as soon as it
is safe to do so.
4WD warning light (4WD
models)
The 4WD warning light comes on when the key
switch is turned to ON. It turns off soon after the
engine is started.
If the 4WD system malfunctions or the revolu-
tion, or radius of the front and the rear wheel
differs, the warning light will either remain illumi-
nated or blink. See “Using four-wheel drive
(4WD)” in the “5. Starting and driving” section.
CAUTION
If the warning light comes on while
driving, 4WD mode will change to
2WD mode. Reduce the vehicle speed
and have your vehicle checked by a
NISSAN dealer as soon as possible.
Do not drive on dry hard surface
roads in the LOCK mode.
If the 4WD warning light blinks when
you are driving:
•blinks rapidly (about twice a sec-
ond):
Pull off the road in a safe area, and
idle the engine. The driving mode
will change to 2WD to prevent the
4WD system from malfunctioning.
If the warning light turns off, you
can drive again.
•blinks slowly (about once every 2
seconds):
Pull off the road in a safe area, and
idle the engine. Check that all tire
sizes are the same, tire pressure iscorrect and tires are not worn.
If the warning light is still on after the
above operation, have your vehicle
checked by a NISSAN dealer as soon as
possible.
Low washer fluid warning light
This light comes on when the washer tank fluid is
at a low level. Add washer fluid as necessary.
See “Window washer fluid” in the “8. Mainte-
nance and do-it-yourself” section.
Seat belt warning light
The light and chime remind you to fasten seat
belts. The light illuminates whenever the ignition
key is turned to ON, and will remain illuminated
until the driver’s seat belt is fastened. At the
same time, the chime will sound for about 6
seconds unless the driver’s seat belt is securely
fastened.
See “Seat belts” in the “1. Safety — Seats, seat
belt and supplemental restraint system” section
for precautions on seat belt usage.
Instruments and controls
2-9
06.4.14/T30-J/V5.0
Page 73 of 281
Supplemental air bag warning
light
After turning the ignition key to the ON position,
the supplemental air bag warning light will illu-
minate. The supplemental air bag warning light
will turn off after about 7 seconds if the system is
operational.
If any of the following conditions occur, the
supplemental front air bag, supplemental side air
bag and pre-tensioner seat belt need servicing,
and your vehicle must be taken to your nearest
NISSAN dealer.
The supplemental air bag warning light re-
mains on after approximately 7 seconds.
The supplemental air bag warning light
flashes intermittently.
The supplemental air bag warning light does
not come on at all.
Unless checked and repaired, the Supplemental
Restraint System and/or the pre-tensioner seat
belt may not function properly. For additional
information, see “Supplemental restraint system”
in the “1. Safety — Seats, seat belt and supple-
mental restraint system” section.
WARNING
If the supplemental air bag warning
light is on, it could mean that the
supplemental front air bag, supplemen-
tal side air bag and/or pre-tensioner
seat belt will not operate in an accident.
To help avoid injury to yourself or oth-
ers, have your vehicle checked by a
NISSAN dealer as soon as possible.INDICATOR LIGHTS
Cruise main switch indicator
light
The light comes on when the cruise control main
switch is pushed. The light goes out when the
main switch is pushed again. When the cruise
main switch indicator light comes on, the cruise
control system is operational.
Cruise set indicator light
The light comes on while the vehicle speed is
controlled by the cruise control system. If the
light blinks while the engine is running, it may
indicate the cruise control system is not func-
tioning properly. Have the system checked by a
NISSAN dealer.
4WD mode indicator light
(AUTO) (4WD models)
This light comes on when the ignition switch is
turned to ON, and turns off within 1 second.
While the engine is running, this light will illumi-
nate when selecting AUTO mode. See “Using
four-wheel drive (4WD)” in the “5. Starting and
driving” section.
4WD mode indicator light
(LOCK) (4WD models)
This light comes on when the ignition switch is
turned to ON, and turns off within 1 second.
When selecting LOCK mode while the engine is
running, this light will illuminate simultaneously
with the 4WD mode indicator light (AUTO)
illuminating. See “Using four-wheel drive
(4WD)” in the “5. Starting and driving” section.
Front fog light indicator light (if
so equipped)
The light comes on when the front fog light
switch is turned on.
High beam indicator light
(Blue)
This light comes on when the headlight high
2-10
Instruments and controls
06.4.14/T30-J/V5.0
Page 154 of 281
5 Starting and drivingPrecautions when starting and driving ............................ 5-2
Exhaust gas (Carbon monoxide) ................................. 5-2
Three way catalyst .......................................................... 5-3
Avoiding collision and rollover ..................................... 5-3
On-pavement and offroad driving precautions ....... 5-4
Drinking alcohol/drugs and driving ............................ 5-4
Driving safety precautions ............................................ 5-4
Ignition switch ....................................................................... 5-6
Automatic transmission (AT) ........................................ 5-6
Manual transmission (MT) ............................................ 5-7
Key positions ................................................................... 5-8
NISSAN Vehicle Immobilizer System ........................ 5-8
Before starting the engine ................................................. 5-9
Starting the engine ............................................................... 5-9
Driving the vehicle ............................................................. 5-10
Automatic transmission ............................................... 5-10
Manual transmission .................................................... 5-14
Parking brake ...................................................................... 5-15
Cruise control ..................................................................... 5-16
Precautions on cruise control ................................... 5-16
Cruise control operations ........................................... 5-17Break-in schedule .............................................................. 5-18
Increasing fuel economy .................................................. 5-18
Using four-wheel drive (4WD) (if so equipped) ........ 5-19
4WD mode switch operations .................................. 5-20
4WD warning light ....................................................... 5-21
Parking/parking on hills .................................................... 5-23
Power steering .................................................................... 5-24
Brake system ....................................................................... 5-24
Braking precautions ..................................................... 5-24
Anti-lock brake system (ABS) .................................. 5-25
Vehicle dynamic control (VDC) system
(if so equipped) .................................................................. 5-26
Cold weather driving ......................................................... 5-28
Freeing a frozen door lock ......................................... 5-28
Antifreeze ........................................................................ 5-28
Battery ............................................................................. 5-28
Draining of coolant water ........................................... 5-28
Tire equipment .............................................................. 5-28
Special winter equipment .......................................... 5-29
Driving on snow or ice ................................................ 5-29
Engine block heater ..................................................... 5-30
06.4.14/T30-J/V5.0
Page 158 of 281
Many hills are too steep for any ve-
hicle. If you drive up them, you may
stall. If you drive down them, you may
not be able to control your speed. If
you drive across them, you may roll
over.
Do not shift gears while driving on
downhill grades as this could cause
loss of control of the vehicle.
Be sure to use the engine brake. The
foot brake performance may be re-
duced, resulting in a possible acci-
dent.
Stay alert when driving to the top of a
hill. At the top there could be a drop-
off or other hazard that could cause
an accident.
If your engine stalls or you cannot
make it to the top of a steep hill,
never attempt to turn around. Your
vehicle could tip or roll over. Always
back straight down in R (Reverse)
gear. Never back down in N (Neutral)
or with the clutch depressed (manual
transmission vehicles), using only thebrake, as this could cause loss of
control.
Heavy braking going down a hill
could cause your brakes to overheat
and fade, resulting in loss of control
and an accident. Apply brakes lightly
and use a low range to control your
speed.
Unsecured cargo can be thrown
around when driving over rough ter-
rain. Properly secure all cargo so it
will not be thrown forward and cause
injury to you or your passengers.
To avoid raising the center of gravity
excessively, do not exceed the rated
capacity of the roof rack (if so
equipped) and evenly distribute the
load. Secure heavy loads in the cargo
area as far forward and as low as
possible. Do not equip the vehicle
with tires larger than specified in this
manual. This could cause your ve-
hicle to roll over.
Do not grip the inside or spokes of
the steering wheel when driving off-road. The steering wheel could move
suddenly and injure your hands. In-
stead drive with your fingers and
thumbs on the outside of the rim.
Before operating the vehicle, ensure
that the driver and all passengers
have their seat belts fastened.
Always drive with the floor mats in
place as the floor may become hot.
Lower your speed when encountering
strong crosswinds. With a higher
center of gravity, your NISSAN is
more affected by strong side winds.
Slower speeds ensure better vehicle
control.
Do not drive beyond the performance
of the tires, even with 4WD engaged.
Accelerating quickly, sharp steering
maneuvers or sudden braking may
cause loss of control.
If at all possible, avoid sharp turning
maneuvers, particularly at high
speeds. Your NISSAN four wheel
drive vehicle has a higher center of
Starting and driving
5-5
06.4.14/T30-J/V5.0
Page 159 of 281
gravity than a two wheel drive ve-
hicle. The vehicle is not designed for
cornering at the same speeds as con-
ventional two wheel drive vehicles.
Failure to operate this vehicle cor-
rectly could result in loss of control
and/or a roll over accident.
Always use tires of the same type,
size, brand, construction (bias, bias-
belted or radial), and tread pattern on
all four wheels. Install tire chains on
the front wheels when driving on slip-
pery roads and drive carefully.
Be sure to check the brakes immedi-
ately after driving in mud or water.
See “Brake system” later in this sec-
tion for wet brakes.
Avoid parking your vehicle on steep
hills. If you get out of the vehicle and
it rolls forward, backward or side-
ways, you could be injured.
Whenever you drive off-road through
sand, mud or water as deep as the
wheel hub, more frequent mainte-
nance may be required. See “Peri-odic maintenance” in the “Service
and Maintenance Guide”.
Do not drive continuously on sandy
or muddy roads with the front wheels
spinning. The 4WD warning light
blinks and the driving mode changes
to 2WD. This could reduce traction
force remarkably. Be especially care-
ful when towing a trailer. (4WD mod-
els)
Do not use 2-wheel chassis dyna-
mometers or 2-wheel free rollers.
(4WD models)
Never operate the accelerator pedal
with any wheels raised and the other
wheels on the ground while jacking
up or with any wheels on a roller and
the other wheels on the ground. Oth-
erwise, the vehicle could lurch for-
ward or backward. (4WD models)
When a wheel is off the ground due
to an unlevel surface, do not spin the
wheel excessively. (4WD models)
AUTOMATIC TRANSMISSION (AT)The ignition lock is designed so that the key
cannot be turned to LOCK and removed until the
selector lever is moved to the P (Park) position.
When removing the key from the ignition, make
sure the selector lever is in the P (Park) position.
If the selector lever is not returned to P (Park)
position, the key cannot be moved toward
LOCK.
When the key cannot be turned toward the
LOCK position, proceed as follows to remove
the key:
SSD0392
Automatic Transmission (AT)
IGNITION SWITCH
5-6
Starting and driving
06.4.14/T30-J/V5.0
Page 172 of 281
leave the windows closed to reduce drag.
The ALL MODE 4X4 system is used to select
2WD, AUTO or LOCK depending on the driving
conditions.
ALL MODE 4X4 system electronically controls
the coupling. Move the 4WD mode switch to
select 2WD, AUTO or LOCK.
WARNING
A vehicle equipped with 4WD (Four-
Wheel Drive) should never be tested
using a two wheel dynamometer, orsimilar equipment. Make sure you in-
form the test facility personnel that your
vehicle is a 4WD equipped vehicle be-
fore it is placed on a dynamometer.
Failure to do so may result in transmis-
sion damage or unexpected vehicle
movement which could result in serious
vehicle damage or personal injury.
SSD0349A
4WD MODE SWITCH
USING FOUR-WHEEL DRIVE
(4WD) (if so equipped)
Starting and driving
5-19
06.4.14/T30-J/V5.0
Page 173 of 281
4WD mode switch Wheels driven4WD mode indicator light
(
,
) Use conditions
2WDFront wheels
The wheel drive mode is in
Two-Wheel Drive (2WD) when
driving on the normal road.*1Goes offFor driving on dry, paved
roads (Economy drive)
AUTODistribution of torque to the
front and rear wheels changes
automatically, depending on
road conditions encountered
[ratio; 100 : 0 (2WD)→50 :
50 (4WD)]. This results in im-
proved driving stability.
For driving on paved or
slippery roads
LOCK Four-Wheel Drive (4WD)*2
/
For driving on rough
roads
*1: 2WD mode may change to 4WD mode automatically during quick acceleration.
The 4WD mode indicator light does not illuminate.
*2: LOCK mode will change to AUTO mode automatically, when the vehicle is accelerated.
4WD MODE SWITCH OPERATIONSThe 4WD mode switch electronically controls
the coupling. Move the switch to select between
each mode, 2WD, AUTO and LOCK, depending
on driving conditions.
WARNING
Depending on the driving condition, the
4WD mode may automatically changefrom 2WD to 4WD even when the 2WD
mode switch is selected.*
Do not start engine while in the 2WD,
AUTO or LOCK mode in the following
cases:
When on a free-roller or jacking up
the front tires with the rear tires on
the ground.
When towing with the rear tires
raised from the ground.
* The 4WD mode indicator light does not illumi-
nate even if the mode automatically changes
from 2WD to 4WD while driving.
4WD shift tipsIf the 4WD mode switch is operated while
making a turn, accelerating or decelerating,
or if the key switch is turned off while in the
AUTO or LOCK, you may feel a jerk. This is
normal.
The oil temperature of power train parts will
increase if the vehicle is continuously oper-
ated under conditions where the difference in
rotation between the front and rear wheels is
large (wheels slip) by driving the vehicle
5-20
Starting and driving
06.4.14/T30-J/V5.0
Page 179 of 281
vehicle to a NISSAN dealer for repair at your
earliest convenience.
WARNING
The anti-lock brake system is a sophis-
ticated device, but it cannot prevent ac-
cidents resulting from careless or dan-
gerous driving techniques. It can help
maintain vehicle control during braking
on slippery surfaces, but remember that
the stopping distance on slippery sur-
faces will be longer than on normal
surfaces, even with the anti-lock sys-
tem. Stopping distances may also be
longer on rough, gravel or snow covered
roads, or if you are using tire chains.
Always maintain a safe distance from
the vehicle in front of you. Ultimately,
the responsibility for safety of self and
others rests in the hands of the driver.
Tire type and condition of tires may also
affect braking effectiveness.
When replacing tires, install the
specified size of tires on all fourwheels.
When installing a spare tire, make
sure it is the proper size and type as
specified on the tire placard. See
“Vehicle identification” in the “9.
Technical and consumer informa-
tion” section for tire placard location.When accelerating or driving on a slippery sur-
faces, the tires may spin or slide. With the
Vehicle Dynamic Control (VDC) system, sensors
detect these movements and control the braking
and engine output to help improve vehicle sta-
bility.
When the VDC system is operating, the
“SLIP” indicator in the instrument panel
blinks.
When only the Traction Control System
(TCS) portion of the VDC system is operat-
ing, the “SLIP” indicator in the instrument
panel blinks.
If the “SLIP” indicator blinks, the road condi-
tions are slippery. Be sure to adjust your
speed and driving to these conditions. Be
sure to drive carefully. See “Slip indicator
light”, and “Vehicle Dynamic Control (VDC)
OFF indicator light” in the “2. Instruments and
controls” section.
Indicator light
If a malfunction occurs in the system, the
“SLIP” and “VDC OFF” indicator lights illumi-
nate in the instrument panel. As long as these
indicators are illuminated, the VDC system
function is canceled.
The VDC system uses an Active Brake Limited
Slip (ABLS) system to improve vehicle traction.
VEHICLE DYNAMIC CONTROL
(VDC) SYSTEM (if so equipped)
5-26
Starting and driving
06.4.14/T30-J/V5.0
Page 182 of 281
to meet the SAE standard minimum clear-
ances between the tire and the closest ve-
hicle suspension or body component re-
quired to accommodate the use of a winter
traction device (tire chains or cables). The
minimum clearances are determined using
the factory equipped tire size. Other types
may damage your vehicle. Use chain tension-
ers when recommended by the tire chain
manufacturer to ensure a tight fit. Loose end
links of the tire chain must be secured or
removed to prevent the possibility of whip-
ping action damage to the fenders or under-
body. If possible, avoid fully loading your
vehicle when using tire chains. In addition,
drive at a reduced speed. Otherwise, your
vehicle may be damaged and/or vehicle han-
dling and performance may be adversely
affected.
Do not use tire chains on dry roads.
Tire chains must be installed only on the
front wheels and not on the rear wheels.
Do not drive with tire chains on paved roads
which are clear of snow. Driving with chains in
such conditions can cause damage to the vari-
ous mechanisms of the vehicle due to some
overstress.
4. For all wheel drive:
If you install snow tires, they must also be thesame size, brand, construction and tread
pattern on all four wheels.
SPECIAL WINTER EQUIPMENTIt is recommended that the following items be
carried in the vehicle during winter:
a scraper and stiff-bristled brush to remove
ice and snow from the windows and wiper
blades.
a sturdy, flat board to be placed under the
jack to give it firm support.
a shovel to dig the vehicle out of snow-drifts.
extra window washer fluid to refill the reser-
voir tank.DRIVING ON SNOW OR ICE
WARNING
Wet ice (32°F, 0°C and freezing rain),
very cold snow or ice can be slick and
very hard to drive on. The vehicle will
have a lot less traction or grip under
these conditions. Try to avoid driving
on wet ice until the road is salted or
sanded.Whatever the condition, drive with
caution. Accelerate and slow down
with care. If accelerating or down-
shifting too fast, the drive wheels will
lose even more traction.
Allow more stopping distance under
these conditions. Braking should be
started sooner than on dry pavement.
Allow greater following distances on
slippery roads.
Watch for slippery spots (glare ice).
These may appear on an otherwise
clear road in shaded areas. If a patch
of ice is seen ahead, brake before
reaching it. Try not to brake while
actually on the ice, and avoid any
sudden steering maneuvers.
Do not use cruise control on slippery
roads.
Snow can trap dangerous exhaust
gases under your vehicle. Keep snow
clear of the exhaust pipe and from
around your vehicle.
Starting and driving
5-29
06.4.14/T30-J/V5.0
Page 194 of 281
TOWING RECOMMENDED BY
NISSAN
Two-Wheel drive modelsNISSAN recommends that your vehicle be
towed with the driving (front) wheels off the
ground or place the vehicle on a flatbed truck as
illustrated.
CAUTION
Never tow automatic transmission
models with the front wheels on theground or four wheels on the ground
(forward or backward) as this may
cause serious and expensive damage
to the transmission.
If it is necessary to tow the vehicle
with the rear wheels raised, always
use towing dollies under the front
wheels.
When towing automatic transmission
models with the front wheels on tow-
ing dollies:•Turn the ignition key to the OFF
position, and secure the steering
wheel in a straight ahead position
with a rope or similar device.
Never secure the steering wheel
by turning the ignition key to the
LOCK position. This may damage
the steering lock mechanism.
•Move the selector lever to the N
(Neutral) position.
When towing Two-Wheel drive auto-
matic transmission model with the
rear wheels on the ground (if you do
not use towing dollies): Always re-
lease the parking brake.
SCE0495
Two-Wheel drive models
In case of emergency
6-11
06.4.14/T30-J/V5.0