change key battery OLDSMOBILE INTRIGUE 1998 Owners Manual

Programmable Automatic Power Door
Locks (ADL)
Programmable Automatic Power Door Locks is a
standard feature intended
to provide enhanced security
and convenience by automatically locking and
unlocking vehicle doors. The automatic locking and
unlocking of the vehicle will occur if the ignition key is
in
ON and the driver’s door is closed when the vehicle is
shifted out
of PARK (P). One of four operating modes
may be selected and programmed by the driver:
Mode 1: No automatic door lock or unlock.
Mode 2: Automatic all door lock when transaxle shifted
out of PARK (P).
No automatic door unlock.
Mode 3: Automatic all door lock when transaxle shifted
out of PARK
(P). Automatic all door unlock when
transaxle shifted into PARK
(P).
Mode 4: Automatic all door lock when transaxle shifted
out of PARK
(P). Automatic driver’s door only unlock
when transaxle shifted into PARK
(P).
The operating mode of the Programmable Automatic
Power Door Locks will be changed when the driver
performs the following sequence with the doors closed
and the ignition key is in
ON.
1. Press and hold the power door lock switch in the
lock position to change this feature.
2. While holding the door lock switch, cycle the
transaxle out of and back into PARK
(P).
3. After an initial transaxle cycle, each additional cycle
will increment the operating mode by one, starting
from the current operating mode.
4. During this customization procedure, the Automatic
Door Lock and Unlock functions shall operate as
defined by each mode listed, providing the customer
with feedback of the current operating mode.
5. If cycled beyond mode 4, the vehicle shall enter
operating mode
1. When the door lock switch is
released, the vehicle shall remain in the most recent
operating mode.
The Programmable Automatic Power Door Locks will
be in operating mode
3 when the vehicle is shipped from
the factory.
Disconnecting the battery for up to a year will not
change the programmed mode
of the Programmable
Automatic Power Door Locks.
2-6
ProCarManuals.com

You can customize the vehicle to activate the Last Door
Closed Locking feature as described previously
or to
completely disable the Last Door Closed Locking
feature at all times. If disabled, the doors will lock
immediately when a power door lock switch is pressed.
The Last Door Closed locking feature is enabled and
disabled when the doors are closed and the ignition key
is in
ON.
Press and hold the power door lock switch in the unlock
position. While holding the door unlock switch, cycle
the transaxle out of and back into PARK
(P). After an
initial transaxle cycle, each additional cycle will toggle
the enable/disable state
of the Last Door Closed Locking
feature. During this customization procedure, the chime
will sound, providing the driver feedback. A single
chime will be heard if the Last Door Closed Locking
feature
is disabled and two chimes will be heard if the
Last
Door Closed Locking feature is enabled. When the
door unlock switch is released, the vehicle will remain
in the most recent operating mode.
The Last Door Closed Locking feature will be enabled
when the vehicle is shipped from the factory.
Disconnecting the vehicle’s battery for up to a year will
not change the programmed mode of the Last Door
Closed Locking feature.
Keyless Entry System
If your vehicle has this option, you can lock and unlock
your doors or unlock your trunk from about
3 feet (1 m)
up to
30 feet (9 m) away using the remote keyless entry
transmitter supplied with your vehicle.
Your keyless entry system operates on a radio frequency
subject to Federal Communications Commission (FCC)
Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation of
the device.
Changes or modifications to this system by other than an
authorized service facility could void authorization to
use this equipment.
2-8
ProCarManuals.com

Disconnecting the battery for up to a year will not
change the programmed mode of the Remote Activation
Verification functions.
Illumination on Remote Activation
This feature is included on vehicles with the Remote
Keyless Entry (RKE) system. The interior illumination
will be activated when an
RKE door unlock command
is received. The ignition must be off for the Remote
Activation Illumination to work. The interior lamps will
illuminate until the ignition is turned to ON
or until the
illumination period of
40 seconds has elapsed.
If during the illumination period, a door is opened, the
timed illumination period will be canceled, though the
interior lamps will remain
on until all doors are closed.
Matching Transmitter(s) To Your Vehicle
Each remote keyless entry transmitter is coded to
prevent another transmitter from unlocking your vehicle.
If a transmitter is lost or stolen, a replacement can be
purchased through your retailer. Remember to bring any
remaining transmitters with you when you
go to your
retailer. When the retailer matches the replacement transmitter
to your vehicle, any remaining transmitters
must also be matched. Once your retailer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have only four transmitters
matched to it.
Battery Replacement
Under normal use, the battery in your remote keyless
entry transmitter should last about two years.
You can tell the battery is weak
if the transmitter won’t
work at the normal range in any location. If you have to
get close to your vehicle before the transmitter works,
it’s probably time to change the battery.
NOTICE:
When replacing the battery, use care not to touch
any of the circuitry. Static from your body
transferred to these surfaces may damage
the transmitter.
2-11
ProCarManuals.com

To replace your battery:
1. Insert a flat object like a dime into the slot on the
back
of the transmitter. Gently pry apart the front
and back.
2.
3.
4.
5.
Gently pry the battery out of the transmitter.
Put the new battery into the transmitter as shown
on
the transmitter (use a type CR2032 battery).
Put the two halves back together. Make sure the
halves are together tightly
so water won’t get in.
Resynchronize and then test the transmitter.
Resynchronizing Your Remote Keyless
Entry Transmitter
After you have changed the battery in your keyless
entry transmitter, you will need to resynchronize the
transmitter.
To do this, press the LOCK and UNLOCK
buttons together and hold for approximately seven
seconds (or until the horn chirps three times). You will
need to use this procedure
if your vehicle has lost
battery power for an extended period
of time.
-
ProCarManuals.com