fuse OPEL GT-R 1973 User Guide

98.40 1973 OPEL SERVICE MANUAL
2. Interconnect manifold and gage set (J-5725-01),
gage charging lines (J-5418) and gage adapters
(J-5420) to air conditioning system as shown in Figure
9B-40.3. Place transmission in “Park” for automatics and
in neutral for manuals. Apply hand brake.
4. Turn blower switch to the “Hi” position.
5. Turn temperature switch to “Max” position.
6. Run engine at 2000 RPM for ten (10) minutes with
car doors and windows closed and the hood up. Place
a high volume industrial type fan in front of radiator
if head pressure should exceed 250 psi and also at
high ambients to bring the pressures to within the
limits specified in the Functional Charts in Division
V.In the case of the Opel 1900 and the Manta, a ther-
mometer should be placed in a position to read the
temperature of the air discharging from the right-
hand A/C outlet. In case of the GT, a thermometer
should be placed in a position to read the tempera-
ture of the air discharging from the left-rear A/C
outlet.
HEATER-AIR CONDITIONER REFRIGERANT
CIRCUIT TROUBLE DIAGNOSIS GUIDE
Insufficient Cooling (Check Air Flow)
Normal Air Flow (Inspect system for visual defects.
Run functional tests.)
Discharge Air
- Normal Temp Check for air leaks
through dash, car body, windows, or from heater or
ventilators.
Discharge Air
- High Temp Check sight glass for
foaming and compressor clutch for engagement.
No Compressor Clutch Engagement Check connec-
tions at clutch switch, harness connectors, and check
clutch switch.
No Foaming Compare evaporator pressure to that
on functional test table.
Foaming System is probably low on refrigerant.
Check for leaks, repair, evacuate, and charge. If
foaming still occurs, check for restriction in refriger-
ant lines between condenser and receiver dehydrator.
Evaporator Pressure Normal Compare head pres-
sure to pressure on functional test table.
Evaporator Pressure Low Ice may be forming on
evaporator. Low volume of air discharging at A/C
outlet after system has been running above idle con-dition
,for approximately 15-30 min.utes. Discharging
air gradually elevating in temperature. Check expan-
sion valve. If valve isn’t permitting flow of liquid,
this will be indicated by a warm pipe out of the
evaporator. This may be caused by: 1) Clogged or
Plugged inlet screen in the expansion valve; 2)
Broken capillary line; or 3) Discharged temperature
bulb. If the valve is okay, the pipe out of the evapora-
tor will be cold.
Evaporator Pressure High Check the expansion
valve to determine if themobulb is making good con-
tact and is properly insulated. Operate engine at 2000
RPM with maximum air conditioning setting. If
evaporator pressure remains high, feel suction line.
If line feels frosty or extremely
(cold with relative
high ambient conditions, then partially cover the
condenser to obtain head pressures from 265 psi to
280 psi maximum. If evaporator pressure rises above
30 psi, change the expansion valve.
Also, check if compressor may be the cause due to
some internal or external mechanical trouble which
prevents reduction of pressure. Check for external
troubles, slipping belt, bad clutch and/or pulley, or
improper clutch engagement, before investigating
the compressor internally.
Head Pressure High Check for the following: Con-
denser air flow low, air in system, excessive refriger-
ant in system, restriction in condenser.Head.PressureLowRestriction in flow of refrigerant
to evaporator, or expansion valve plugged or defec-
tive.
Low Air Flow (Check blower operation and
evaporator. Check operation of controls.)
Ice BIocking Evaporator Run functional test. If
evaporator pressure is low, ice may form on evapora-
tor and reduce air flow.
Evaporator Pressure Low Ice may be forming on
evaporator. Low volume of air discharging at A/C
outlet after system has been running above idle con-
dition for approximately 15-30 minutes. Discharging
air gradually elevating in temperature. Check expan-
sion valve. If valve isn’t permitting flow of liquid,
this will be indicated by a warm pipe out of the
evaporator. This may be caused by: 1) Clogged or
plugged inlet screen in the expansion valve; 2)
Broken capillary line, or 3) Discharged temperature
bulb. If the valve is okay, the pipe out of the evapora-
tor will be cold.BlowerNot OperatingCheck for the following: Fuse
blown, blower switch defective, wire broken or loose
connection, poor ground connection, or blower mo-
tor defective.

96-52 1973 OPEL SERVICE MANUAL
REMOVAL AND INSTALLATION OF EVAPORATOR
AND EXPANSION VALVE. OPEL 1900 - MANTA
Removal
1. Remove negative battery cable from battery.
2. Remove left side of distributor duct, and in line
fuse. See Figure
9B-61.3. Remove glove box. See Figure
9B-62.Figure 96-64 Delay Restrictor
and Check Valve Hose
Assembly Location
5. Disconnect the delay restrictor and check valve
hose assembly from the vacuum cut-off switch and
disconnect the electrical wiring. See Figures 9B-63
and 64.
6. Remove evaporator inlet and outlet pipes re-
tainer and rubber grommet. See Figure
9B-65.Figure
98.62 Glove Box Removed
4. Discharge refrigerant from system. (Refer to
DISCHARGING SYSTEM) and disconnect refrig-
erant hose from evaporator outlet and pipe from
evaporator inlet and tape the open ends of the refrig-
erant lines and evaporator pipes. See Figure
9B-63.Figure
98.65 Inlet and Outlet Pipes retainer and
Rubber Grommet-Opel 1900 - Manta
Figure
98.63 Location of Refrigerant Hoses, Pipes,
Vacuum Cut Off Switch and Evaporator Attaching Bolt
(Left Side) - Opel 1900
- Manta

96-54 1973 OPEL SERVICE MANUAL
valve. The filter screen at the inlet port may be re-
placed. Remove screen by threading a lo-32 NF
screw into old filter screen. With a washer and a nut
on the screw arranged to work as a puller screw, hold
the body of the screw and turn the nut. Insert the
new filter screen into the inlet port and lightly tap
screen only enough to seat.
1. Install expansion valve using new o-rings during
installation. Lubricate o-rings prior to installation
using No. 525 viscosity oil.
2. Install evaporator assembly and case attaching
screws. See Figure 9B-70.3. Install blower motor assembly into case and se-
cure with attaching screws. See Figure
9B-69.4. Install finger guard shields and fan housing case.
See Figure
9B-69.5. Install resistor assembly and electrical connector.
Install blower motor connector. See Figure
9B-69.6. Install assembly into car carefully guiding
evaporator pipes up through cowl opening. See Fig-
ure
9B-71.Figure 93-7 1 Inlet and Outlet Pipes and O-Rings
-Opel 1900 Manta
7. Install two (2) upper attaching evaporator at-
taching nuts. See Figures 9B-66 and
9B-67.8. Install two (2) attaching case mounting bracket
to instrument panel screws. See Figure
9B-67.9. Connect two (2) drain hoses underneath evapora-
tor.10. Install evaporator inlet and outlet pipes retainer
and rubber grommet. See Figure
9B-65.11. Connect vacuum cut-off switch and electrical
wiring, making sure the delay restrictor and checkvalve hoses are installed correctly. See Figures
9B-63and 64.
.gB-72 Delay Restrictor and Check Valve Hose.Assembly
12. Install refrigerant hoses and pipes using new
o-rings on line fittings and evacuate system. Refer to
EVACUATING SYSTEM.
13. While system is being evacuated, install in-line
fuse and left side of distributor duct. See Figure 9B-
61.14. Install glove box.
15. Install negative battery cable and charge system.
Refer to CHARGING SYSTEM.
REMOVAL AND INSTALLATION OF CONDENSER
ASSEMBLY -OPEL 1900. MANTA
Removal
1. Remove negative battery cable from battery.
2. Remove air cleaner.
3. Discharge system. Refer to DISCHARGING
SYSTEM.
4. While system is discharging, remove lower radia-
tor hose from radiator and drain coolant into a suita-
ble container.
5. Remove fan shroud.
6. On vehicles with automatic transmission, un-
screw oil lines from connectors on lower radiator
tank and plug lines. It is essential that no dirt enters
the oil lines. When unscrewing oil lines, hold connec-
tors on lower radiator tank with pliers to avoid leak-
ages. Ensure that no dirt enters oil cooler.
7. Remove upper radiator hose from radiator.
8. Remove lower attaching nut and slide radiator
upward and out of engine compartment.
9. Remove inlet and outlet hoses from condenser

AIR CONDITIONER SYSTEM -OPEL 1900 - MANTA9B- 91FAN DOES NOT RUN Correct electrical fault.
FAN RUNS
- Check air velocity.
NOT OK Clean evaporator inlets.
Clean evaporator core.
Clean evaporator outlets.
OK Check refrigeration (refer to Refrigeration
Diagnosis Guide).
MAINTENANCE AND ADJUSTMENTS
ADJUSTMENT OF THERMOSTATIC SWITCHThe system makes use of a thermostatic switch with
a self-supporting air sensing capillary. This capillary
controls the switch by sensing the temperature of the
air leaving the evaporator fins.
Checking for Proper Operation
I. Install the gauge set and set up the vehicle as
described under FUNCTIONAL TESTING SYS-
TEM iti Refrigerant Components Section.
2. Movement of the temperature control knob
should result in a definite change in suction pressure
and cycling of the compressor clutch.
3. If compressor continues to operate regardless of
the knob adjustment, it indicates that the switch
points are fused, which will lead to evaporator
freeze- up. The switch should be replaced.
Adjusting Switch
If, after ihe foregoing checks, the switch seems to be
operating correctly, adjust for proper setting if neces-
sary, as
~follows:1. Set up car as described in FUNCTIONAL
TESTING SYSTEM in Refrigerant Components
Section.2. The suction side of the system, read on the low
pressure gauge, should pull down to the pressure
shown in the chart in SPECIFICATIONS in Refrig-
erant Components Section.
3. Remove the face plate retaining screws and
remove face plate assembly noting the position of the
air sensipg capillary so that it can be reinstalled in
the same location as when removed. See Figure 98.170. ,:Figure
98.170 Location of Air Sensing Capillary
4. Remove the thermostatic switch retaining screws
and remove switch. Remove the non-metal end plate
from the switch to gain access tq the switch adjusting
screw. Check the screw for stripped or otherwise
damaged threads.
5. If the low side pressure
was less than the pre-
scribed pressure at the end of each cooling cycle, turn
the adjusting screw a partial turn clockwise. See Fig-
ure
9B-171.Figure 9B-17 1 Adjusting
Thkmosfatic Switch
6. If the pressure was more than the prescribed
value, turn the adjusting screw counter-clockwise.
7. Reinstall switch end plate and install switch in
face plate. Install face plate on ,evaporator assembly
assuring that the air sensing
c&pillary has been re-
placed properly.
8. Check system performance. Fffurther adjustment
is needed, repeat steps 3 thru 7 until the correct
pressure is reached.
Do not attempt to run a performance test with the
face plate and switch removed
,from the evaporator
assembly
- inaccurate reading, will result. Always
replace the switch and face plate assemblies before
checking the system performance.

AIR CONDITIONER SYSTEM. OPEL 1900. MANTA9B- 93
2. Remove the left side of distributor duct, and the
in-line fuse. See Figure 9B-174.98.139Figure SB-174 Location of Distributor Duct (Left Side)
Retaining Screws
Figure SB-175 Removing Left Side Distributor Duct
3. Rembve the glove box assembly. See Figure 9B-
176.
4. Discharge refrigerant from system, (refer to DIS-
CHARGING SYSTEM) and disconnect refrigerant
hose from evaporator outlet and pipe from evapora-
tor inlet’and tape the open ends of the refrigerant
lines and evaporator pipes. See Figure
9B-178.5. Disconnect the delay restrictor and check valve
hose assembly from the vacuum cut-off switch and
disconnect the electrical wiring. See Figure
9B-180.6. Rempve evaporator inlet and outlet pipes re-
tainer and rubber grommet. See Figure
9B-178.Figure SB-176 Glove
Bdx Removed
Figure SB-178 Location of Refrigerant Hoses, Pipes,
Vacuum Cut Off Switch and Evaporator Attaching Bolt
(Left Side)
Figure 9B-180 Vacuum Hoses and Wiring

AIR CONDITIONER SYSTEM -OPEL 1900 - MANTA9B- 95
Figure 96.185 Evaporator Inlet and Outlet Pipes andO-Rings
7. Connect the 2 drain hoses underneath evapora-
tor.
8. Install evaporator inlet and outlet pipes retainer
and rubber grommet. See Figure
9B-178.
9. Connect vacuum cut-off switch and electrical
wiring,, making sure the delay restrictor and check
valve hose are installed correctly. See Figure
9B-180.
10. Install refrigerant hoses and pipes using new o-
rings on line fittings and evacuate system. Refer to
EVACUATING SYSTEM.
Il. While system is being evacuated install the in-line
fuse and left side of distributor duct. See Figure
9B-
174.
12. Install the glove box.
Figure 98.186 Delay Restrictor and Check Valve Hose
Assembly
Figure 9B-187 Fuse Block Connections
13. Install negative battery cable and charge the sys-
tem. Refer to CHARGING SYSTEM.

98.96 1973 OPEL SERVICE MANUALr DARK BLUE
LIGHT BLUE STRIPE
CUTOUT111111DARK GREEN DARK GREEN
,,
I
,\,\
BATTERYl LJ
\flu- +tL-2+- -7- -RESISTOR
A
EXlSilNG‘IWIRE
I
I
IFUSE BLOCK*,*,- I./SWITCH
r
ti‘WIREfIfI
1- IAAI
i$+.-lAC~,‘XESW WIRE
I I
TTEVAPO.RATOREVAPO.RATOR
BLACK WITH RED STRIPE BLACK WITH RED
Sl96-143
Figure 9B-188 Wiring Schematic‘RIPE96-143
Figure 9B-188 Wiring Schematic
SPECIFICATIONS
Blower Motor Type
......................................................................................................12 VDC
Blower Fan Type
..................................................................................................Squirrel Cage

98.98 1973 OPEL SERVICE MANUALDIAGNOSISTROUBLE DIAGNOSIS GUIDE
Insufficient Cooling
CHECK AIR FLOW
FAN DOES NOT RUN
- Correct electrical fault.
FAN RUNS
- Check air velocity.
NOT OK
- Clean evaporator inlets.
Clean evaporator core.
Clean evaporator outlets.
OK
- Check refrigeration (refer to Refrigeration
Diagnosis Guide).
MAINTENANCE AND ADJUSTMENTS
ADJUSTMENT OF THERMOSTATIC SWITCHThe system makes use of a thermostatic switch with
a self-supporting air sensing capillary. This capillary
controls the switch by sensing the temperature of the
air leaving the evaporator tins.
Checking for Proper Operation
1. Install the gauge set, and set up the vehicle as
described under FUNCTIONAL TESTING SYS-
TEM in Refrigerant Components Section.
2. Movement of the temperature control knob
should result in a definite change in suction pressure
and cycling of the compressor clutch.
3. If compressor continues to operate regardless of
the knob adjustment it indicates that the switch
points are fused, which will lead to evaporator
freeze-up. The switch should be replaced.
Adjusting Switch
If after the foregoing checks, the switch seems to be
operating correctly, adjust for proper setting if neces-
sary, as follows:
1. Set up car as described in FUNCTIONAL
TESTING SYSTEM in Refrigerant Components
Section.
2. The suction side of the system, read on the lowpressure gauge, should pull down to the pressure
shown in the chart in SPECIFICATIONS in Refrig-
erant Components Section.
3. Remove the duct assembly mtaining screws and
remove the duct assembly noting the position of the
air sensing capillary so that it can be reinstalled in
the same location as when removed. See Figure 9B-
190.Figure 98.190 Duct Assembly and Retaining Screws
Figure 9B-13 1 Duct Assembly
4. Remove the thermostatic switch retaining screws
and remove switch. Remove the non-metal end plate
from the switch to gain access to the switch adjusting
screw. Check the screw for stripped or otherwise
damaged threads.

RADIO. GT9c- 105
RADIO
GTCONTENTS
Subject
DESCRIPTION AND OPERATION: (Not Applicable)
DIAGNOSIS:
RadioTroubleDiagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAINTENANCE AND ADJUSTMENTS:
Antenna Trimmer Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAJOR REPAIR:
RemovingandInstallingRadio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SPECIFICATIONS: (Not Applicable)
Page No.
9c-105
9C-106
9c-107
DIAGNOSIS
RADIO TROUBLE DIAGNOSISBecause radio problems are most often repaired at
United Delco authorized warranty repair stations,
the tendency for many dealer servicemen is to
remove the set when a problem is reported, without
any preliminary diagnosis. This results in a large
number of radios showing up as “NO TROUBLE
FOUND” units when received by the warranty re-
pair stations. This indicates that the trouble can
often be corrected without removal of the radio.
The inconvenience to an owner of driving without a
radio while his set is being serviced at a warranty
station can frequently be avoided if the following
quick checks are used to eliminate external radio
system :problems before removing the radio for re-
pair.
Always determine from the owner the exact nature
of the radio problem as an aid to diagnosis. Knowing
whether the condition is intermittent or constant,
whether it occurs with engine off or running, with
car stationary or moving, will help to pinpoint the
problem. Never turn on radio with speaker discon-
nected.
Radio Ii
Inoperative.1. Turn on the radio. The dial should light and a
thump should be heard from the speaker.a. If a thump is heard, go to Step No. 2 for antenna
check.b. If no thump is heard,
check the fuse.
(1) If fuse is bad, replace and try radio again. Race
engine and, if fuse blows again,‘remove the radio and
speaker assembly for repair by
4 trained radio techni-
cian.
(2) If fuse is good, check to
s&e that the speaker-to-
receiver interconnecting cable is connected securely.
If there is still no thump when the radio is turned on,
remove the receiver and speaker for repair.
2. Check the antenna by substituting with one held
out the car window.
a. If radio is still dead with substitute antenna,
remove the receiver and spea!er for repair.
b. If radio operates near normal with substitute an-
tenna, some part of the car antenna or lead-in is at
fault.
Radio Reception Is Weak1. Check to see if antenna trimmer is peaked.
a. Position antenna at a height of 31 inches.
b. Tune radio to weak station at or near 1400 KHz
on the dial, and turn volume control to maximum.

RADIO - OPEL 1900 - MANTA9c- 109
RADIO
OPEL 1900
- MANTA
CONTENTS
Subject
DESCRIPTION AND OPERATION: (Not Applicable)
DIAGNOSIS:
RadioTroubleDiagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAINTENANCE AND ADJUSTMENTS:
Antenna Trimmer Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAJOR REPAIR:
Removal&InstallationRadio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal81InstallationAntenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SPECIFICATIONS:Page No.
9c-109
9c-110
9c-111
9c-111
DIAGNOSIS
RADIO TROUBLE DIAGNOSISBecause radio problems are most often repaired at
United Delco authorized warranty repair stations,
the tendency for many dealer servicemen is to
remove the set when a problem is reported, without
any preliminary diagnosis. This results in a large
number of radios showing up as “NO TROUBLE
FOUND” units when received by the warranty re-
pair stations. This indicates that the trouble can
often time be corrected without removal of the radio.
The inconvenience to an owner of driving without a
radio while his set is being serviced at a warranty
station can frequently be avoided if the following
quick checks are used to eliminate external radio
system Problems before removing the radio for re-
pair.
Always determine from the owner the exact nature
of the radio problem as an aid to diagnosis. Knowing
whether! the condition is intermittent or constant,whether::it occurs with engine off or running, with
car stationary or moving, will help to pinpoint theproblem: Never turn on radio with speaker discon-
nected.
Radio Is Inoperative
1. Turn on the radio. The dial should light and a
thump should be heard from the speaker.a. If a thump is heard, go to
Step No. 2 for antenna
check.b. If no thump is heard, check the fuse.
(1) If fuse is bad, replace and try radio again. Race
engine and, if fuse blows again, remove the radio and
speaker assembly for repair by a trained radio techni-
cian.
(2) If fuse is good, check to see that the speaker to
receiver interconnecting cable is connected securely.
If there is still no thump when the radio is turned on,
remove the receiver and speak+ for repair.
2. Check the antenna by substituting with one held
out the car window.
a. If radio is still dead with’substitute antenna,
remove the receiver and speaker for repair.
b. If radio operates near normal with substitute an-
tenna, some part of the car antenna or lead-in is at
fault.
Radio Reception Is Weak1. Check to see if antenna
tri$mer is peaked.
a. Position antenna at a height,of 31 inches.
b. Tune radio to weak station at or near 1400 KHz
on the dial, and turn volume control to maximum.