key battery Peugeot 206 CC 2003 Owner's Manual

30-06-2003
YOUR 206 CC IN DETAIL
72
Changing the battery of the remote control
Warning that the battery is flat is given by an audible signal accompa-nied by the message
''Remote
control battery low'' on the multi-
function display.
To replace the battery, remove the screw then unclip the casing using acoin at the ring (CR 2016/3 volt battery). If the remote control does not work after the battery has been changed,reprogramme the remote control.
THE KEYS The keys allow you to
independent-
ly operate the locks on the doors,
the tailgate (opening), the fuel filler cap, the steering lock, the glove boxand the passenger air bag disarmingcontrol and to switch on the ignition. Central locking From the driver's door the keys allow you:
Ðto lock or unlock the doors and tail-
gate simultaneously,
Ð to unlock simultaneously just thedoors.
Unlocking the boot is possible
only by using the boot key. If one of the doors is open, the cen- tral locking does not work. The remote control This fulfils the same functions as the
key, at a distance. Locking Pressing button
Alocks the vehicle
by remote control. This is displayed by the continuouslighting of the direction indicators forapproximately two seconds. Unlocking Pressing button Bunlocks just the
doors. This is shown by the rapid flashingof the direction indicators. Notes: if the vehicle is locked and
the unlocking control is pressed inadvertently without the doorsbeing opened within 30 seconds, the
vehicle will lock again automatically.
Avoid pressing the buttons of your remote control out of range of your
vehicle. You risk causing it not towork and the remote control wouldhave to be reprogrammed.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition. Locating your car
To locate your car in a car park, if you have locked it: 
press button A, the courtesy light
comes on and the direction indi- cators flash for a few seconds.Programming the remote control  Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove the remote control key from the
ignition lock. The remote control isnow working again.

30-06-2003
Important After deadlocking the vehicle, the doors can only be unlocked fromthe outside of the vehicle; if anyo-ne is inside the vehicle, it is impos-sible to unlock the vehicle from theinside. If the battery is disconnected:- the deadlocking remains activa- ted
- it is possible to open one of the front doors using the ignition
key, but the key only opens the
corresponding door.
CENTRAL LOCKING Pressing button Aallows you to lock
or unlock the doors from the inside. Note: on vehicles fitted with this
control, the door handles only ope- rate the door concerned.
SPECIAL FEATURES 129
Warning: it is dangerous to activate the deadlocking ifanyone is inside the vehicle Make a careful note of the
number of the key.
If the key is lost or stolen you will
then be able to obtain a new key. Check that the batteries are not flat.

30-06-2003
The alarm Setting and deactivating the alarm system Switching off the siren. The alarm completes the security
equipment for your vehicle. It offerstwo types of protection. -external protection: when it is
set, the alarm sounds if one of
the doors, the boot lid or the bonnet is opened ;
- internal protection: when it is
set, the alarm sounds if the sen-
sors detect air movement in thepassenger compartment (a bro-ken window) or movementwithin the car .
Note: the internal protection does
not operate when the vehicle roof isopen or is not closed properly (e.g.catches unlocked). The alarm also has an anti-tamper function. If there is an attempt to tamper with the wires to the siren, control unit or
the battery,the siren sounds and thedirection indicators light. Setting the alarm (external andinternal protection)
Switch the ignition off and get out of the vehicle. Deadlock the vehicle.The doors lock.The direction indicators light for two seconds. The red light on the switch flashes once a second.
5 seconds later, internal protection is set.
45 seconds later, external protection is set. Note:
when the alarm is triggered,
the siren sounds for thirty seconds. After the thirty seconds it stops, butthe alarm remains set.
Warning: When the alarm is trigge-
red, if a door, the boot lid, roof or
bonnet are not closed correctly, thesiren sounds for a moment. If thevehicle is closed correctly in the fol-lowing 45 seconds, the alarm is acti-vated and the direction indicatorsremain on for two seconds. In allcases, the alarm is activated after 45seconds. Disarming the alarm (internal and external protection) Press the release button of the
remote control key. The doors unlock.The direction indicators flash for two seconds. The red light on the switch goes out. Note:
if the warning light continues
to flash after de-activation of the alarm, it is a sign that the alarm has
been triggered. The flashing willstop when the ignition is switchedon.
SPECIAL FEATURES
130

30-06-2003
Emergency cut-off (If the remote control is not working)
Unlock the doors with the key.
Open the door.The alarm is triggered.
- Turn on the ignition.
- The locking system recognisesthe key.
- The siren stops and the alarm is disarmed. Selection of the type of protection
To set the alarm to external
protection only. If you want to leave a window par- tially open, or a pet inside thevehicle, you need to select externalprotection only:
- Switch off the ignition.
- Within the next ten seconds,
press the internal protection but- ton 1 until the warning light comes
on continuously. Get out of thevehicle.
- Deadlock the vehicle.
- The doors lock.
- The direction indicators light for two seconds.
- The red light on the switch flashes once a second.
To de-activate external protection only Press the release button on the remote control. The doors unlock.The direction indicators flash for two seconds. The red light on the switch goes out. To lock the vehicle without setting the alarm It is the remote control which sets the alarm. Therefore, to lock the vehicle without setting the alarm: use the
key.
To recharge or replace the battery:
- Turn on the ignition.
- You have 10 seconds after turning
on the ignition to press the inter- nal protection switch 1and hold it
down for two seconds.
- The warning light flashes rapidly for three seconds.
- You can now disconnect the battery.
After reconnecting the battery:
- Deadlock, then unlock the vehicle using the remote control.
The alarm will be set after the next deadlocking operation.
SPECIAL FEATURES 131
In no circumstances must you carry out modificationsto the alarm.

30-06-2003
PRACTICAL INFORMATION
112
BATTERY
To charge the battery using a battery charger:
- Disconnect the battery,
- Follow the instructions for use given by the battery charger manufacturer,
- Reconnect starting with the negative (-) terminal,
- Check that the terminals and connectors are clean. If they are covered with
sulphate (white or greenish deposit), disconnect them and clean them.
To start the vehicle from another battery:
- Connect the red cable to the positive (+) terminals of the two batteries,
- Connect one end of the green or black cable to the negative (-) terminal of the slave battery,
- Connect the other end of the green or black cable to an earth point on the bro- ken down vehicle as far as possible from the battery,
Operate the starter, let the engine run.
Wait for the engine to return to idle, then disconnect the cables. ECONOMY MODE FUNCTION After the engine has stopped, with the key in the accessories position,
certain functions (windscreen wiper,electric windows, courtesy lights,audio equipment etc.) can only beused for thirty minutes, to prevent
discharging the battery.
Once the thirty minutes are over, the message
"Economy mode active"
appears on the multifunction displayand the active functions are put on
standby.
A flat battery will prevent the engine from starting.
- Wait for 2 minutes after switching off the ignition before disconnec- ting the battery.
- Never disconnect a terminal when the engine is running.
- Never charge a battery without first disconnecting the terminals.
- Close the windows and the folding roof before disconnecting the battery. If the windows do not operate normally following re-connection of the battery, you must re-initialise them (see section "Electric windows - ¤ Safety auto-reverse).
- After every reconnection of the battery, switch on the ignition and wait 1 minute before starting to allow the electronic systems to be initialised. If slight difficulties are experienced after this, please contact a PEUGEOT
dealer. It is advisable to disconnect the battery if the vehicle is not
to be used for a period of more than one month.