spare wheel Peugeot 206 P Dag 2010 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 206 P Dag, Model: Peugeot 206 P Dag 2010Pages: 107, PDF Size: 3.94 MB
Page 73 of 107
!
78
TEMPORARY REPAIR OF
A TYRE
Vehicles which are not equipped with a
spare wheel have two tyre repair aero-
sols stored in an insulated storage box
in the boot.
(See also the instructions on the aero-
sols). - Remove the foreign body if possible.
- Position the wheel so that the valve
is vertical to the ground.
- Shake the aerosol vigorously before use. (In very cold weather, warm the
aerosol for a few minutes in your
hands).
- F i x t h e a e r o s o l ’ s fl e x i b l e c o n n e c - tor onto the valve, keeping it cen-
tralised.
- Hold the valve against the hole in the wheel rim.
- Empty the 2 aerosols one after the other, held upright, until the tyre is
s a t u r a t e d ( n o f u r t h e r fl o w v i s i b l e i n
the connector)
- Remove the connector and immedia- tely drive at least 3 miles (5 km),
at moderate speed .
- If possible, check the pressure of the tyre.
- Then immediately drive at moderate
speed to the nearest garage. The aerosol cans enable you to
carry out a temporary repair (maxi-
mum speed 50 mph (80 km/h)).
After use, have the vehicle exam-
ined by a professional who will
assess whether the tyre can be
repaired or must be replaced.
As the aerosol cans are pres-
surised, they must not be exposed
to a temperature above 50 °C.
Store them away from heat in
their insulated storage box.
Page 74 of 107
79
CHANGING A WHEEL
Operating procedure for replacing a
faulty wheel with the spare wheel using
the tools provided with the vehicle.
Parking the vehicle
- If possible, park the vehicle on level, stable and non-slippery ground.
- Apply the parking brake, engage fi r s t o r r e v e r s e g e a r . Access to the spare wheel and
the jack
The wheel is located outside the ve-
hicle, under the boot, supported by a
metal carrier.
- Remove the wheelbrace
1 , secured
on the rear right inner panel of
the boot .
- Using the wheelbrace 1 , slacken the
spare wheel carrier retaining bolt,
located inside the boot under the
carpet .
- Lift the carrier to release the hook rearwards, then lower it.
- Remove the jack storage case 2
located in the spare wheel. Removing a wheel
- Chock the rear of the wheel diagonally
opposite the wheel to be changed.
- Remove the wheel trim using the wheelbrace, by pulling at the valve
passage hole.
- Slacken the wheel bolts.
- Place the jack under the locating point on the sub-frame E that is
closest to the wheel to be changed.
Ensure that the entire surface of the
jack base plate is in contact with the
ground.
- Extend the jack, completely unscrew the bolts and remove the wheel.
Page 75 of 107
!
80
Fitting the wheel
- Once the wheel is in place, pre-tight-en it lightly using the wheelbrace.
- Fold the jack and remove it.
- Tighten the bolts using the wheel- brace.
- R e fi t t h e w h e e l t r i m s t a r t i n g a t t h e valve passage hole and press with
the palm of the hand. Putting the wheel back in place
- Put the jack storage case back in
the wheel.
- Put the wheel back in the carrier.
- Raise the wheel, then the carrier and reposition the hook.
- Do not forget to retighten the spare wheel carrier retaining bolt fully.
- Stow the wheelbrace. For your safety, always change a
wheel:
- on level, stable and non slip-
pery ground,
- with the parking brake applied, ignition off,
- w i t h fi r s t o r r e v e r s e g e a r e n - gaged,
- with the vehicle chocked,
- you must ensure that the oc- cupants get out of the vehicle
and wait in a safe location,
- never go underneath a vehicle raised using a jack (use an
axle stand).
The jack and all of the tools are
s p e c i fi c t o y o u r v e h i c l e . D o n o t
use them for other purposes.
After changing the wheel
- Have the tightening of the bolts and the pressure of the
spare tyre checked as soon
as possible by a PEUGEOT
dealer.
- Have the punctured tyre re- paired and replace it on the
vehicle as soon as possible.
Page 76 of 107
81
SPECIAL FEATURES OF ALLOY WHEELS
Bolt covers
Alloy wheel bolts are covered by chrome
trims.
Use the yellow tool 4 to remove the
trims before slackening the bolts.
The yellow tool 4 is located:
- in the glove box or,
- in the jack storage case. Fitting the spare wheel
If your vehicle is equipped with a steel
s p a r e w h e e l , w h e n fi t t i n g i t , i t i s
normal
to notice that the bolt washers do not
come into contact with the rim. The
spare wheel is secured by the cone
shape of each bolt.
Fitting snow tyres
I f y o u fi t s n o w t y r e s t h a t a r e m o u n t e d o n
steel rims on your vehicle, it is essential
that you use special bolts available from
PEUGEOT dealers.