ECU Peugeot 207 CC 2014 Owner's Guide

7
!
DRIVING
11 7
207CC_EN_CHAP07_CONDUITE_ED01-2014
When the cruise control is switched
on, be careful if you maintain the
pressure on one of the programmed
speed changing buttons: this may
result in a very rapid change in the
speed of your vehicle.
Do not use the cruise control on
slippery roads or in heavy traffi c.
On a steep descent, the cruise
control will not be able to prevent
the vehicle from exceeding the pro-
grammed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is secured correctly,
- never fi t one mat on top of an- other.
Programming
 Turn dial 1 to the "CRUISE" po-
sition: the cruise control mode is
selected but is not switched on
(OFF).
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed
speed results in fl ashing of this speed on the display.
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically can-
cels the fl ashing of the speed.
Return to normal driving
 Turn dial 1 to the "0" position: the cruise control mode is
deselected. The display returns to the distance recorder.
Operating fault
In the event of a cruise control mal-
function, the speed is cleared result-
ing in fl ashing of the dashes. Contact a
PEUGEOT dealer or a qualifi ed work-
shop to have the system checked.
 Set the programmed speed by
accelerating to the required
speed, then press button 2 or 3
(e.g.: 70 mph (110 km/h)).
 Switch off the cruise control by pressing button 4 : the
display confi rms that it has been switched off (OFF).
 Switch the cruise control back on by pressing button 4
again.
You can then change the programmed speed using but-
tons
2 and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.

8
i
!
CHECKS
121
207CC_EN_CHAP08_VERIFICATIONS_ED01-2014
BONNET
Protects the components of the engine
and provides access for checking levels.
 Push the exterior safety catch B to
the left and raise the bonnet.  Unclip the stay
C from its housing.
 Fix the stay in one of the two notch- es to hold the bonnet open.
Closing
 Take the stay out of the support notch.
 Clip the stay in its housing.
 Lower the bonnet and release it at the end of its travel.
 Pull on the bonnet to check that it is secured correctly.
RUNNING OUT OF FUEL
(DIESEL)
Opening
 Open the front left door.
 Pull the interior release lever A ,
located at the bottom of the door
frame.
The location of the interior release
lever prevents opening of the bon-
net while the left hand front door is
closed.
When the engine is hot, handle the
exterior safety catch and bonnet
stay with care (risk of burns).
1.6 litre HDi engine
 Fill the fuel tank with at least fi ve li-tres of diesel.
 Open the bonnet.
 If necessary, unclip the styling cover for access to the priming pump.
 Squeeze and release the priming pump repeatedly until resistance is
felt (there may be resistance at the
fi rst press).

Operate the starter until the engine
starts (if the engine does not start at the
fi rst attempt, wait around 15 seconds
before trying again).
 If the engine does not start after a few attempts, operate the priming
pump again then start the engine.
 Clip the styling cover back in place.
 Close the bonnet. On vehicles fi tted with HDi engines, the
fuel system must be primed if you run
out of fuel; refer to the corresponding
engine compartment view.
If the tank on your vehicle is fi tted with
a misfuel prevention device, refer to the
"Misfuel prevention (Diesel)" section.
Because of the presence of elec-
trical equipment under the bonnet,
it is recommended that exposure
to water (rain, washing, ...) be re-
stricted. If the engine does not start fi rst time,
don't keep trying but start the procedure
again from the beginning.

9
i
PRACTICAL INFORMATION
133
207CC_EN_CHAP09_INFO PRATIQUES_ED01-2014
* According to country.
CHANGING A WHEEL *
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.
Access to the tools
The tools are installed in a box at the
bottom of the boot under the spare
wheel.
For access to them, refer to the para-
graph "Access to the spare wheel" on
the following page. List of tools
1. Wheelbrace.
For removal of the wheel trim and
removal of the wheel fi xing bolts.
2. Jack with integral handle.
For raising the vehicle.
3. "Bolt cover" tool.
For removal of the bolt protectors (covers) on alloy wheels.
4.
Socket for the security bolts (located
in the glove box).
For adaptation of the wheelbrace to the special "security" bolts. 5. Removable towing eye.
Refer to the paragraph "Towing the vehicle".
All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.
Other accessories
Wheel with trim
When removing the wheel ,
detach the trim fi rst using the
wheelbrace 1 pulling at the valve
passage hole.
When refi tting the wheel , re-
fi t the trim starting by placing its
notch facing the valve and press
around its edge with the palm of
your hand.

9
i
i
PRACTICAL INFORMATION
134
207CC_EN_CHAP09_INFO PRATIQUES_ED01-2014
Access to the spare wheel
The "space-saver" spare wheel is in-
stalled in the boot under the fl oor.
To gain access to it:
 place the vehicle in the "coupé" con-fi guration,
 open the boot,
 raise the fl oor.
Fixing the "space-saver" spare
wheel
If your vehicle is fi tted with alloy
wheels, it is normal to notice, when
tightening the bolts on fi tting, that
the washers do not come into con-
tact with the "space-saver" spare
wheel. The wheel is secured by the
conical contact of each bolt.
Taking out the wheel
 Slacken and remove the retaining
strap.
 Raise the spare wheel towards you from the rear.
 Take the wheel out of the boot.
Putting the wheel back in place
 Put the spare wheel back in its housing.
 Put the retaining strap back in place and tighten it.
 Put the boot fl oor back in place.
Tyre under-infl ation detection
The spare wheel is not fi tted with a
sensor. The punctured wheel must
be repaired by a PEUGEOT dealer.

9
i
PRACTICAL INFORMATION
135
207CC_EN_CHAP09_INFO PRATIQUES_ED01-2014
Parking the vehicle
Immobilise the vehicle where it
does not block traffi c: if possible,
park the vehicle on level, stable
and non-slippery ground.
Apply the parking brake, switch off
the ignition and engage fi rst gear *
to lock the wheels.
If necessary, place a chock under
the wheel diagonally opposite the
wheel to be changed.
It is imperative that you ensure that
the occupants get out of the vehicle
and wait in a safe location.
Never go underneath a vehicle
raised using a jack; use an axle
stand.
Removing a wheel List of operations
 Remove the chromed bolt cover from each of the bolts using the tool 3 .
 If your vehicle is equipped with this, fi t the security socket 4 on the
wheelbrace 1 to slacken the security
bolt.
 Slacken the other bolts using the wheelbrace 1 only.
 Place the jack 2 in contact with one
of the two front A or rear B locations
provided on the underframe, which-
ever is closest to the wheel to be
changed.
 Extend the jack 2 until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A
or B used.
 Raise the vehicle until there is suf- fi cient space between the wheel and
the ground to admit the spare (not
punctured) wheel easily.
 Remove the bolts and store them in a clean place.
 Remove the wheel.
*
position P for the automatic gearbox.

9
i
PRACTICAL INFORMATION
136
207CC_EN_CHAP09_INFO PRATIQUES_ED01-2014
After changing a wheel
Using the "space-saver" spare wheel:
 do not fi t the wheel trim,
 do not exceed a speed of 50 mph (80 km/h).
Have the tightening of the bolts and
the pressure of the spare wheel
checked by a PEUGEOT dealer
without delay.
Have the punctured wheel repaired
and replace it on the vehicle as
soon as possible.
Fitting a wheel List of operations
 Put the wheel in place on the hub.
 Screw in the bolts by hand.
 Pre-tighten the security bolt us- ing the wheelbrace 1 fi tted with the
security socket 4 (if your vehicle is
equipped with this).
 Pre-tighten the other bolts using the wheelbrace 1 only.
 Lower the vehicle fully.
 Fold the jack 2 and detach it.
 Tighten the security bolt using the wheelbrace 1 fi tted with the security
socket 4 (if your vehicle is equipped
with this).
 Tighten the other bolts using the wheelbrace 1 only.
 Refi t the chromed bolt covers on each of the bolts.
 Store the tools in the box at the bottom of the boot.
 Store the punctured wheel in a corner of the boot.

9
!
PRACTICAL INFORMATION
147
207CC_EN_CHAP09_INFO PRATIQUES_ED01-2014
BATTERY
Procedure for charging your battery
when it is fl at or for starting the engine
using another battery.
Access to the battery
Starting using another battery
 Connect the red cable to the posi-tive terminal (+) of the fl at battery A ,
then to the positive terminal (+) of
the slave battery B .
 Connect one end of the green or black cable to the negative termi-
nal (-) of the slave battery B .
 Connect the other end of the green or black cable to the vehicle's offset
earth point.
 Start the support vehicle.
 Operate the starter of the broken down vehicle and let the engine run.
 Wait until the engine returns to idle and disconnect the cables.
The battery is located under the bonnet.
To gain access to it:
 open the bonnet using the interior re-
lease lever, then the exterior safety
catch,
 secure the bonnet stay,
 lift the plastic cover on the (+) terminal.
Certain vehicle functions may not
be available if the battery is not suf-
fi ciently charged.

9
i
!
i
PRACTICAL INFORMATION
153
207CC_EN_CHAP09_INFO PRATIQUES_ED01-2014
ACCESSORIES
A wide range of accessories and genu-
ine parts is available from the PEUGEOT
dealer network.
These accessories and parts have
been tested and approved for reliability
and safety.
They are all adapted to your vehicle and
benefi t from PEUGEOT's recommen-
dation and warranty. Depending on the legislation in
force in the country, certain safety
equipment may be compulsory:
high visibility safety vests, warn-
ing triangles, breathalyzers, spare
bulbs, spare fuses, a fi re extin-
guisher, a fi rst aid kit, mud fl aps at
the rear of the vehicle.
The fi tting of electrical equipment
or accessories which are not rec-
ommended by PEUGEOT may
result in a failure of your vehicle's
electronic system and excessive
electrical consumption.
Please note this precaution. You are
advised to contact a PEUGEOT rep-
resentative to be shown the range of
recommended equipment and ac-
cessories.
"Comfort":
door defl ectors, side blinds and rear
blind, coat hanger fi xed to head re-
straint, front centre armrest, under shelf
storage, front and rear parking sen-
sors...
Installation of radio
communication transmitters
Before installing any after-market ra-
dio communication transmitter, you
can contact a PEUGEOT dealer for
the specifi cation of transmitters which
can be fi tted (frequency, maximum
power, aerial position, specifi c instal-
lation requirements), in line with the
Vehicle Electromagnetic Compatibil-
ity Directive (2004/104/EC).
"Transport solutions":
boot liner, luggage net, cigarette lighter,
roof bars, bicycle carrier on roof bars,
ski carrier, roof box...
Towbar, which must be fi tted by PEUGEOT
dealer or a qualifi ed workshop.
"Styling":
aluminium gear lever knob, spoiler, styling
strips, alloy wheels, trims, chromed mirror
shells, body kit... * To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned and secured correctly,
- never fi t one mat on top of another.
"Security":
anti-theft alarm, window engraving,
wheel security bolts, child seats and
booster cushions, breathalyzer, fi rst aid
kit, warning triangle, high visibility jacket,
stolen vehicle tracking system, tempo-
rary puncture repair kit, snow chains,
non-slip covers, front foglamps kit...
"Protection":
mats * , seat covers compatible with lateral
airbags, aluminium or PVC door aperture
fi nishers...
"Multimedia":
audio systems, satellite navigation
systems, hands-free kit, CD changer,
speakers, DVD player, connection kit
for MP3 or CD player, USB Box...
You can also obtain products for clean-
ing and maintenance (exterior and in-
terior), topping up (screenwash...), and
refi lls (cartridge for the temporary punc-
ture repair kit...) by visiting a PEUGEOT
dealer.