ESP Peugeot 208 2012 Owner's Guide

119
5
Visibility











Courtesy lamp
In this position, the cour tesy lamp comes on gradually:


Take care to avoid leaving anything in contact with the courtesy lamp. - when the vehicle is unlocked,
- when the ke
y is removed from the ignition,
- when opening a door,
- when the remote control locking button is
pressed, in order to locate your vehicle.
It switches o
ff gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed.
Permanentl
y off.
Permanent lighting.
) With the ignition on, press
the corresponding switch.
1.Front cour tesy lamp2. Map reading lamp s
With the "permanent lighting" mode, the lightingtime varies according to the circumstances:

- with the ignition off, approximately ten
minutes,

- in energy economy mode, approximatelythirty seconds, -with the engine running, unlimited.



Front map reading lamps

121
6
Safety














Direction
indicators
)Lower the lighting control stalk fully when moving to the left. )Raise the lighting control stalk fully when moving to the right.


"Motorway" function

Move the stalk briefly upwards or downwards,
without going beyond the point of resistance;
the corresponding direction indicators will flash 3 times.
If you forget to cancel the direction indicators for more than twenty seconds, the volume of the audible signal will increase if the speed is above40 mph (60 km/h).







Hazard warning lamps
A visual warning by means of the direction indicators to aler t other road users to a vehicle
breakdown, towing or accident.
Automatic operation of
hazard warnin
g lamps
When braking in an emergency, depending on
the deceleration, the hazard warning lamps come on automatically.
They switch off automatically the first time you accelerate.)
You can also switch them off by pressingthe button.
)
Press this button, the direction indicators
flash.
They can operate with the ignition off.

123
6
Safety
Electronic Stability Programme incorporatingthe following systems:


- the anti-lock braking system (ABS) and the electronic brake force distribution (EBFD),

- the emergency braking assistance,

- the anti-slip regulation (ASR) or tractioncontrol,

- the d
ynamic stability control (DSC).






























Electronic stability programme (ESP)
Definitions
Anti-lock braking system (ABS)
and electronic brake force
distribution (EBFD)
This system improves the stability and
manoeuvrability of your vehicle when braking and provides improved control in corners, in par ticular on poor or slippery road surfaces.
The ABS prevents wheel lock in the event of
emergency braking.
The electronic brake
force distribution system
manages the braking pressure wheel by wheel.
Emergency braking assistance
In an emergency, this system enables you to reach the optimum braking pressure more
quickly and therefore reduce the stopping distance. It is triggered in relation to the speed at which
the brake pedal is pressed. This is felt by a reduction in the resistance of the pedal and an increase in the effectiveness of the braking.

Anti-slip regulation (ASR)

The ASR system (also known as Traction Control) optimises traction in order to avoid
wheel slip by acting on the brakes of the drivingwheels and on the engine. It also improves
the directional stability of the vehicle onacceleration.


Dynamic stability control(DSC)

If there is a difference between the path
followed by the vehicle and that required bythe driver, the DSC monitors each wheel and
automatically acts on the brake of one or more
wheels and on the engine to return the vehicle
to the required path, within the limits of the laws of physics.

131
6
Safety
Lateral airbags

Deployment
The lateral airbags are deployed unilaterally in
the event of a serious side impact applied to all
or par t of the side impact zone B , perpendicular
to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside
towards the inside of the vehicle.
The lateral airbag inflates between the hip andshoulder of the front occupant of the vehicle
and the corresponding door trim panel.
System which protects the driver and frontpassenger in the event of a serious side impact
in order to limit the risk of injury to the chest,
between the hip and the shoulder.
Each lateral airba
g is fitted in the seat backrestframe, door side.
Impact detection zones
A.
Front impact zone.
B. Side impact zone.


Curtain airbags
System which protects the driver and passengers (with the exception of the rear centre passenger) in the event of a serious sideimpact in order to limit the risk of injury to the side of the head.
Each curtain airbag is built into the pillars and
the upper passenger compar tment area.
In the event of a minor impact or bump on the side of the vehicle or if the vehicle rolls over, the airbag may not be deployed.
In the event of a rear or front collision, the airbag is not deployed.



Deployment

The cur tain airbag is deployed at the same
time as the corresponding lateral airbag in the event of a serious side impact applied to all or
part of the side impact zone B , perpendicular
to the longitudinal centreline of the vehicle on a
horizontal plane and directed from the outside
towards the inside of the vehicle.
The cur tain airbag inflates between the front or
rear occupant of the vehicle and the windows.
If this warnin
g lamp comes on in the instrument panel, accompanied byan audible signal and a message in
the screen, contact a PEUGEOT dealer or aqualified workshop to have the system checked.
The airbags may no longer be deployed in the event of a serious impact.

Operating fault

154
Practical information
Fitting a wheel
Fitting the "space-saver"spare wheel
If your vehicle is fitted with alloy wheels, when tightening the bolts on fitting,it is normal to notice that the washers
do not come into contact with the"space-saver" spare wheel. The wheel is secured by the conical surface of each bolt.
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. When using the "space-saver" typespare wheel, do not exceed 50 mph(80 km/h). Have the tightening of the bolts and thepressure of the spare wheel checked by a PEUGEOT dealer or a qualified workshop without delay. Have the punctured wheel repairedand refitted to the vehicle as soon as possible.


List of operations
)Put the wheel in place on the hub. )Screw in the bolts fully by hand.)Pre-tighten the security bolt using the
wheelbrace 1fitted with the security socket 4 (if your vehicle has them). )Pre-tighten the other bolts using the
wheelbrace 1only.

161
7
Practical information
Changing brake lamp, reversing lamp and direction indicator bulbs
These three bulbs are changed from inside the boot:
)open the boot, )remove the access grille from the corresponding side trim panel,)slacken and remove the nut,)disconnect the lamp unit connector, )unclip the lamp unit carefully extract itpulling in line towards the outside,
)
press the four tabs and remove the bulbholder,)
turn the bulb a quar ter of a turn and change it.
To reassemble, carry out these operations inreverse order.
Take care to engage the lamp unit in its guides,while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but without damaging the lamp.

162
Practical information
Changing the third brake lamp
bulbs
)Unscrew the fixing pins on each side of the lamp, without removing them completely.)Push on the screws to unclip the lamp.
)Disconnect the lamp connector.)Remove the lamp from the outside. )Turn the bulb holder which corresponds
to the faulty bulb one quar ter of a turn and remove it.)Pull the bulb and change it.
To r e f i t , c a r ry out these operations in reverse order.
Number plate lamps
To facilitate the removal of the lamp, carry out
this operation with the tailgate half open.
) Insert a thin screwdriver into the lenscutout. )
Push it outwards. )
Remove the lens. )
Change the faulty bulb.
To refit, press on the lens to clip it in place.
Access is by passing a hand under the bumper. )Turn the bulb holder a quarter of a turn and
pull it out. )Disconnect the connector on the bulb holder. )Pull the bulb out and change it.
To r e f i t , c a r ry out these operations in reverse order.
You can also contact a PEUGEOT dealer or a qualified workshop for the replacement of thesebulbs.

Changing a foglamp bulb

164
Practical information
To replace a fuse, you must: )use the special tweezer to extract the fuse
from its housing and check the condition of its filament.)always replace the failed fuse with a fuse
of the same rating (same colour); using a
different rating could cause faults (risk of fire).
If the fuse fails again soon after replacement,have the vehicle's electrical system checked bya PEUGEOT dealer or a qualified workshop.
Changing a fuse
Before changing a fuse:
)the cause of the failure must be identifiedand rectified, )all electrical consumers must be switched
off, )the vehicle must be immobilised with theignition off,)identify the failed fuse using the tables andlayout drawings in the following pages.Good Failed
PEUGEOT will not accept responsibilityfor the cost incurred in repairing your vehicle or for rectifying malfunctions resulting from the installation of accessories not supplied and not
recommended by PEUGEOT andnot installed in accordance with its instructions, in par ticular when thecombined consumption of all of the additional equipment connectedexceeds 10 milliamperes.



Installing electricalaccessories

Your vehicle's electrical system isdesigned to operate with standard or optional equipment.
Before installing other electrical equipment or accessories on your vehicle, contact a PEUGEOT dealer or a qualified workshop.
The replacement of a fuse not shown in the tables below may cause a serious malfunction of your vehicle. Contacta PEUGEOT dealer or a qualified workshop.
Tweezer

168
Practical information
Fuse N°RatingFunctions
F1
615 A
Front foglamps.
F18 10 A
Right hand main beam headlamp.
F1
910 A
Left hand main beam headlamp.
F25
30 A Headlamp wash relay (accessory).
F2
940 A Front wiper motor.
F3
080 A Pre-heater plugs (Diesel).
Engine compartment fuses
The fusebox is placed in the engine compartment near the battery (left-hand side).
Access to the fuses
)Unclip the cover. )Change the fuse (see corresponding paragraph). )When you have finished, close the cover carefully to ensure correct sealing of the
fusebox.



Fuse table

171
7
Practical information








Load reduction mode

System which manages the use of cer tainfunctions according to the level of charge
remaining in the battery.
When the vehicle is bein
g driven, the load
reduction function temporarily deactivates certain functions, such as the air conditioning,
the heated rear screen...
The deactivated functions are reactivatedautomatically as soon as conditions permit.


It is advisable to disconnect the battery if the vehicle is to be left unused for more than one month.
The batteries contain harmful substances such as sulphuric acid and lead. They must be disposed of in accordancewith regulations and must not, in any circumstances, be discarded with household waste.
Take used remote control batteries andvehicle batteries to a special collection point.

Do not reverse the polarity and use only a 12 V charger. Do not disconnect the terminals whilethe engine is running.
Do not charge the batteries withoutdisconnecting the terminals first.
Do not push the vehicle to star t the engine if you have an electronicgearbox or automatic gearbox.
Before disconnecting the battery
Wait 2 minutes after switching off the ignition
before disconnecting the battery.
Close the windows and the doors before disconnecting the battery.
Following reconnection of thebattery
Following reconnection of the battery, switch on
the ignition and wait 1 minute before star ting to permit initialisation of the electronic systems. However, if problems remain following this
operation, contact a PEUGEOT dealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise:
- the remote control key,
- the on-board satellite navi
gation system.