reset Peugeot 208 2019 Owner's Manual

8
Instrument panels
Rev counter
Rev counter (x 1,000 rpm),
g raduation depends on the
engine.
Indicator
Engine coolant temperature
i n d i c a t o r.
Control button
Servicing reminder.
Setting the time.
Reset the function selected (ser vice indicator
or trip recorder).
Depending on version:
-

S

etting the time.
-
D

igital speedometer.
Instrument panel lighting
Adjusting the intensity of the
general lighting.
Speedometer
Analogue speedometer (mph
or km/h).
Gauge
Fuel gauge.
Instruments

10
Warning and indicator
lamps
Displayed as symbols, visual indicators
which inform the driver of the occurrence
of a malfunction (warning lamps) or of the
operating status of a
system (operation or
deactivation indicator lamps). Certain lamps
light up in two ways (fixed or flashing) and/or in
several colours.
Associated warnings
The illumination of a lamp may be accompanied
b y an audible signal and/or a message
displayed in a
screen.
Relating the type of alert to the operating status
of the vehicle allows you to determine whether
the situation is normal or a
fault has occurred:
refer to the description of each lamp for further
information.
When the ignition is switched on
Certain red or orange warning lamps come on
for a few seconds when the ignition is switched
on. These warning lamps should go off as soon
as the engine is started. (1)
:You must stop as soon as it is safe to do
so and switch off the ignition.
(2): Contact a PEUGEOT dealer or a qualified
workshop.
(3) : Go to a PEUGEOT dealer or a qualified
workshop.
Sport programme.
Snow programme (depending on
engine).
Trip recorder reset
With the trip distance displayed, press the
button for a few seconds.
Persistent warning lamp
When the engine is running or the vehicle is
being driven, the illumination of a red or orange
warning lamp indicates a
fault that needs
further investigation, using any associated
message and the description of the warning
lamp in the documentation.
Where a lamp remains lit
The references (1) , (2) and (3) in the warning
and indicator lamp description indicate whether
you should contact a
qualified professional
in addition to the immediate recommended
actions.
Instruments

20
Indicators
Service indicator
The ser vice indicator is displayed in the
instrument panel. Depending on the vehicle
version:
-
t
he distance recorder display line indicates
the distance remaining before the next
ser vice is due, or the distance travelled
since it was due preceded by the "-" sign.
Warning/indicator
lamp State
CauseActions/
Observations
Ser vice
spanner Lights up temporarily
when the ignition is
switched on.
Between 620 and
1 ,860 miles (1,000 and
3,000
km) remain before
the next ser vice is due.
Fixed, when the
ignition is switched on. The ser vice is due in
less than 620
miles
(1,000


km).Have your vehicle
serviced very soon.
+ Ser vice
spanner
flashing
Flashing then fixed,
when the ignition is
switched on.
(For BlueHDi Diesel
versions, associated
with the Ser vice
warning lamp). The servicing interval
has been exceeded.
Have your vehicle
ser viced as soon as
possible.
The distance indicated (in miles or
kilometres) is calculated according to the
distance covered and the time elapsed
since the last ser vice.
The alert may also be triggered close to
a
due date.
-
a
n alert message indicates the distance
remaining, as well as the period before
the next ser vice is due or how long it is
overdue.
Resetting the service indicator
The ser vice indicator must be reset after each
service.
If you have carried out the ser vice on your
vehicle yourself:
F

s
witch off the ignition,
If you have to disconnect the battery
following this operation, lock the vehicle
and wait at least 5
minutes for the reset to
be registered.
F

p
ress and hold the trip distance recorder
reset button,
F

s
witch on the ignition; the distance recorder
display begins a


countdown,
F

r
elease the button when " =0" is displayed;
the spanner disappears.
Instruments

21
Retrieving the service
information
You can access the ser vice information at any
time.
F
P
ress the trip distance recorder reset
button.
T

he ser vice information is displayed for
a


few seconds, then disappears.
Engine oil level indicator
(depending on version)
On versions fitted with an electric oil level
indicator, the state of the engine oil level is
displayed in the instrument panel for a few
seconds, after the servicing information.
The level read will only be correct if the
vehicle is on level ground and the engine
has been off for more than 30
minutes.
Oil level insufficient
This is indicated by the display of the message
"Oil level incorrect" in the instrument panel,
accompanied by the Ser vice warning lamp and
an audible signal.
Oil level indicator fault
This is signalled by the display of the message
"Oil level measurement invalid" in the
instrument panel.
Contact a PEUGEOT dealer or a qualified
workshop.
In the event of a
fault with the electric
indicator, the oil level is no longer
monitored.
If the system is faulty, you must check the
engine oil level using the manual dipstick
located under the bonnet.
For more information on Checking levels ,
refer to the corresponding section.
Engine coolant temperature
With the engine running, when the needle is:
- i n zone A , the temperature of the engine
coolant is correct, -

i
n zone B
, the temperature of the engine
coolant is too high; the maximum
temperature and the central STOP warning
lamps come on, accompanied by an
audible signal and a

warning message in
the screen.
You must stop as soon as it is safe to do so.
Wait a few minutes before switching off the
engine.
Contact a PEUGEOT dealer or a qualified
workshop. If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to
avoid damage to the engine.
For more information on Checking levels ,
refer to the corresponding section.
1
Instruments

24
Starting preventedYou have exceeded the authorised driving
limit: the starting prevention system does
not allow the engine to be started.
To be able to restart the engine, you must call
on a
PEUGEOT dealer or a qualified workshop.
Each time the ignition is switched on, these
warning lamps come on and the AdBlue
warning lamp flashes, accompanied by an
audible signal and the display of the message
"Emissions fault: Starting prevented".
Trip computer
Instrument panel screen
F Each press on the end of the wiper
control stalk displays the information in
turn. -
Trip
1 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the first trip.
- Trip
2 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the second trip.
-
T
he current information with:
•
t
he range,
•
t
he current fuel consumption,
•
t
he Stop & Start time counter.
With touch screen
The information is accessible via the
Driving/Vehicle
.
Reset trip
F When the desired trip is displayed, press
the button located on the end of the wiper
control stalk for more than 2
seconds.
Trips 1
and 2 are independent and are used
identically.
For example, trip 1
can be used for daily figures
and trip 2
for monthly figures.
Display of information on the touch screen
Instruments

25
Permanent display:
F Sel ect the " Applications " menu, then the
" Vehicle apps " tab, then "Trip computer ".
The trip computer information is displayed in
tabs.
F

P
ress one of the buttons to display the
desired tab.
Temporar y display in a
specific window:
F

P
ress the end of the wiper control stalk
to access the information and display the
different tabs.
The current information tab with:
-

T
he range.
-

T
he current fuel consumption.
-

T
he Stop & Start time counter.
The trip " 1" tab with:
-

T
he average speed for the first trip.
-
T

he average fuel consumption.
-

T
he distance travelled.
The trip " 2" tab with:
-

T
he average speed for the second trip.
-
T

he average fuel consumption.
-

T
he distance travelled.Trip reset
F When the desired trip is displayed, press the reset button or on the end of the wiper
control stalk.
Tr i p s " 1" and " 2" are independent and are used
identically.
For example, trip " 1" can be used for daily
figures and trip " 2" for monthly figures.
A few definitions
Range
(miles or km)
The distance which can still be
travelled with the fuel remaining in
the tank (related to the average fuel
consumption over the last few miles
(kilometres) travelled).
This value may fluctuate if a
change
of driving style or terrain results in
a
significant change in the current fuel
consumption.
Dashes are displayed when the range falls
below 19
miles (30 km).
After filling with at least 5
litres of fuel, the
range is recalculated and is displayed if it
exceeds 60
miles (100 km).
If dashes instead of figures continue
to be displayed when driving, contact
a PEUGEOT dealer or a qualified workshop.
Current fuel consumption
(mpg or l/100 km or km/l)
C alculated over the last few seconds.
1
Instruments

26
This function is only displayed from
19 mph (30 km/h).
Average fuel consumption
(mpg or l/100 km or km/l)
C alculated since the last trip computer
reset.
Distance travelled
(miles or km)
Calculated since the last trip computer
reset.
Average speed
(mph or km/h) Calculated since the last trip
computer reset.
Total time in stop mode
(minutes/seconds or hours/minutes)
If your vehicle is fitted with Stop & Start, a time
counter adds up the time spent in STOP mode
during a

journey.
It resets to zero every time the ignition is
switched on.
Setting the time and date
Instrument panel
F Each press of this button toggles between the following settings:
-


h o u r,
-


minutes,
-

1
2 or 24 hour format.
With PEUGEOT Connect
Radio
F Select the Settings menu in
the upper banner of the touch
screen.
F

Sel

ect " System configuration ".
F

Sel
ect "Date and time ".
F

Sel

ect " Date " or "Time ".
F

C

hoose the display formats.
F

C

hange the date and/or time using the
numeric keypad.
F

C

onfirm with " OK".
With PEUGEOT Connect
Nav
Setting of the time and date is only available if
synchronisation with the GPS is deactivated.
F

Sel
ect the "Settings " menu.
F

P
ress the " OPTIONS " button to go to the
secondary page.
F

Sel
ect "Setting the time- date".
F

Sel
ect the " Date" or " Time" tab.
F

A
djust the date and time using the numeric
keypad and confirm.
F

I
n the selected tab, press this
key to confirm.
Additional settings
You can choose:
- T o change the date format (DD/MM/ Y Y Y Y,
YYYY/MM/DD, etc.)
-

T
o change the time format (12h/24h).
-

T
o change the time zone.
-

T
o activate or deactivate synchronisation
with the GPS (UTC).
Instruments

56
Automatic rain sensitive
windscreen wipers
The windscreen wipers operate
automatically, without any action
on the part of the driver, when rain
is detected (sensor behind the rear
view mirror), adapting their speed to
the intensity of the rainfall.
Switching on
This indicator lamp comes on in the
instrument panel and a message is
displayed.
Give a

short downwards push to the control
stalk.
A wiping cycle confirms that the instruction has
been accepted.
Switching off
This indicator lamp goes off in the
instrument panel and a message is
displayed.
Give another short downwards push to
the control stalk or shift the control stalk to
a

different position (Int, 1 or 2). If the wipers operate in intermittent mode
when in AUTO mode, have the system
checked by a
PEUGEOT dealer or
a

qualified workshop.
Do not cover the rain sensor, combined with
the sunshine sensor, located at the top of
the windscreen behind the rear view mirror.
When using an automatic car wash, switch
off the automatic rain sensitive wipers.
In winter, it is advisable to wait until the
windscreen is completely clear of ice before
activating the automatic rain sensitive
wipers.
Front screenwash
Pull the wiper control stalk towards you. The
screenwash and then the wipers operate for
a
preset time.
Front wipers
Fast (heavy rain).
Normal (moderate rain).
Intermittent (proportional to the
speed of the vehicle).
Of f.
Single wipe (press down and
release). The automatic rain sensitive windscreen
wipers must be reactivated by pushing the
control stalk downwards, if the ignition has
been off for more than 1
minute.
Lighting and visibility

88
With PureTech petrol and manual or
automatic gearbox:
-

A
s soon as the vehicle stops or the speed
is less than 2
mph (3 km/h) (with manual
gearbox and depending on version).
-

W
ith gear lever in neutral and clutch pedal
released (manual gearbox).
-

W
ith brake pedal pressed or gear lever in
position N (automatic gearbox).
Special cases: STOP mode not
available
STOP mode is not triggered when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain
a


comfortable temperature in the passenger
compartment,
-

d
emisting is active,
-

s
ome temporary conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) make this
necessary to ensure control of a
system.
This indicator lamp flashes for a
few
seconds, then goes off.
This operation is perfectly normal. A time counter calculates the
time spent in STOP mode during
a
journey. It is reset to zero every
time the ignition is switched on
using the key.
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The Stop & Start system does not affect
the functionalities of the vehicle, such as
braking.
With a
manual gearbox in STOP mode, if
a
gear is engaged without fully depressing
the clutch pedal, a message is displayed
asking you to depress the clutch pedal
again to restart the engine.
START mode
This indicator lamp goes off and the
engine restarts. With manual gearbox
:
-
W
ith clutch pedal depressed.
With automatic gearbox:
-
W
ith gear lever in position D or M
.
-
W
ith brake pedal released.
or
-
W
ith gear lever in position N.
-
W
ith brake pedal released.
-
T
hen gear lever in position D or M
.
or
-
W
ith reverse gear engaged.
Special cases: START mode
triggered automatically
As a safety measure and for your convenience,
S TART mode is triggered automatically when:
-
y

ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-

s
ome temporary conditions (battery charge,
engine temperature, braking assistance,
air conditioning setting, etc.) make this
necessary to ensure control of a
system or
the vehicle.
This indicator lamp flashes for a
few
seconds, then goes off.
This operation is perfectly normal.
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.
Driving

140
Quick-release terminal clamp
Disconnecting the (+) terminalReconnecting the (+) terminal
Do not force the lever as locking will not
be possible if the clamp is not positioned
correctly; start the procedure again.
Before disconnecting
Wait 2 minutes after switching off the ignition
b efore disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.
Following reconnection
After each time that the battery has been
reconnected, switch on the ignition and wait
1
minute before starting the engine, to allow
the electronic systems to initialise. However,
if minor problems persist after this procedure,
contact a
PEUGEOT dealer or a qualified
workshop.
Referring to the corresponding section, you
must yourself reinitialise:
-

t
he remote control key,
-

t
he date and time,
-

t
he radio preset stations.
F

Ra

ise the lever A fully to release the
clamp B .
F

R

emove the clamp B by lifting it off. F

Ra

ise the lever A fully.
F

R

efit the open clamp B on the (+) terminal.
F

P

ush the clamp B fully down.
F

L

ower the lever A to lock the clamp B .
To w i n g
Procedure for having your vehicle towed or for
towing another vehicle using the towing eye.
F

s

witch off all electrical consumers (audio
system, wipers, lighting, etc.),
F

s

witch off the ignition and wait for 4

m

inutes.
At the battery, it is only necessary to
disconnect the (+) terminal.
In the event of a breakdown