cooling Peugeot 307 2007.5 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2007.5, Model line: 307, Model: Peugeot 307 2007.5Pages: 212, PDF Size: 7.59 MB
Page 20 of 212
INSTRUMENTS and CONTROLS
23
Coolant temperature indicator Engine oil temperature gauge
When the needle is in zone A , the
temperature is correct.
When the needle is in zone B , the tem-
perature is too high. The central STOP
w a r n i n g l i g h t l a s h e s , a c c o m p a n i e d b y
an audible signal and a message on
the multifunction display.
Y o u m u s t s t o p i m m e d i a t e l y .
Warning: wait for the engine to cool
before topping up the level.
The cooling system is pressurised.
In order to avoid any risk of scalding,
unscrew the cap two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level.
Contact a PEUGEOT dealer. When the engine is running, this indi-
cates the oil temperature.
The temperature is too high if the
maximum graduation is reached.
Y o u m u s t s t o p i m m e d i a t e l y .
Contact a PEUGEOT dealer.
P a r k
A u t o m a t i c g e a r b o x l e v e r
p o s i t i o n s i n d i c a t o r
R e v e r s e
Neutral
Drive
Manual mode:
1
s t gear engaged
2
nd gear engaged
3
rd gear engaged
4
th gear engaged
5
th gear
engaged
***
6
th gear engaged ***
*** According to model.
Page 49 of 212
COMFORT
48
The air conditioning only operates
when the engine is running. When the engine is cold, to prevent
too great a distribution of cold air, the
a i r l o w w i l l r e a c h i t s o p t i m u m l e v e l
gradually.
The driver and his front
passenger can each adjust
the temperature to their re-
quirements.
The value indicated on the
display corresponds to a level of
comfort and not to a temperature in
degrees Celsius or Fahrenheit.
Turn control 2 or 3 to the left or to
the right respectively to decrease or
increase this value.
A setting around the v a l u e 2 1 provides
optimum comfort. However, depend-
ing on your requirements, a setting be-
tween 18 and 24 is normal. For optimum comfort, you are ad-
vised to avoid a left/right setting dif-
ference of more than 3.
For maximum cooling or heating of the
passenger compartment, it is possible
to go below the value 15 by turning un-
til
"LO" is displayed or above the value
27 by turning until "HI" is displayed.
4 . A u t o m a t i c v i s i b i l i t y p r o g r a m m e The automatic comfort pro-
gramme may not be suf-
i c i e n t t o q u i c k l y d e m i s t o r
de-ice the windscreen and
side windows (humidity,
several passengers, ice, etc.).
In this case, select the automatic vis-
ibility programme.
The system automatically controls
t h e a i r c o n d i t i o n i n g , t h e a i r l o w a n d
the air intake and provides optimum
distribution of the ventilation to the
windscreen and side windows.
To switch it off, press button 4 again
or press the "AUTO" button, the
button"s indicator light switches off
and "AUTO" is displayed.
A u t o m a t i c o p e r a t i o n
1 . A u t o m a t i c c o m f o r t p r o g r a m m e
Press the "AUTO" button.
The "AUTO" symbol is dis-
played.
We recommend the use of
this mode: it permits auto-
matic and optimised adjustment of
all of the functions, passenger com-
p a r t m e n t t e m p e r a t u r e , a i r l o w , a i r
distribution and air recirculation, in
accordance with the comfort value
that you have chosen. This system is
designed to operate effectively in all
seasons, with the windows closed.
2 . D r i v e r ' s s i d e a d j u s t m e n t
3 . P a s s e n g e r s i d e a d j u s t m e n t On entering the vehicle, if
the interior temperature is
much colder or warmer than
the comfort value, there is no
need to change the value displayed
in order to obtain the comfort re-
quired. The system corrects the dif-
ference in temperature automatically
and as quickly as possible.
DUAL ZONE AUTOMATIC AIR CONDITIONING
Page 50 of 212
49
COMFORT
M a n u a l o p e r a t i o n
If you wish, you can make a different
choice from that offered by the sys-
tem by changing a setting. The other
functions will still be controlled auto-
matically. Pressing the "AUTO" but-
ton returns the system to completely
automatic operation.
Press this button to stop air
cooling.
Avoid prolonged use of this
mode (risk of condensation,
odour, humidity).
Press this button again as soon as
possible to return to automatic op-
eration of the air conditioning. The
symbol "A/C" is displayed.
6 . A i r d i s t r i b u t i o n a d j u s t m e n t Pressing this button sev-
eral times in succession
e n a b l e s t h e a i r l o w t o b e
directed in turn towards:
- the windscreen and side windows (de-icing or demisting),
- the windscreen, the side windows and the footwells,
- the footwells,
- the centre vents, the side vents and the footwells,
- the centre and side vents. 7 . A i r l o w a d j u s t m e n t
Press the
" s m a l l f a n " or " l a r g e f a n "
button respectively to decrease or in-
c r e a s e t h e l o w o f a i r .
T h e a i r l o w s y m b o l , t h e f a n , i l l s p r o -
gressively in relation to the value re-
quired.
8 . A i r i n t a k e / A i r r e c i r c u l a t i o n 9 . D e m i s t i n g t h e r e a r s c r e e n a n d
t h e m i r r o r s
Press this button for recir-
culation of the interior air.
The air recirculation symbol
8 is displayed.
Air recirculation enables the
passenger compartment to be isolat-
ed from exterior odours and smoke.
Avoid prolonged recirculation of inte-
rior air (risk of condensation and de-
terioration of the air quality).
As soon as possible, press this but-
ton again to permit the intake of out-
side air and prevent condensation.
5 . A i r c o n d i t i o n i n g O n / O f f
Press this button to demist
the rear screen and the ex-
terior mirrors. The button
9
indicator light comes on.
Demisting switches off au-
tomatically to prevent an excessive
consumption of current. It is possible
to stop operation of the demisting be-
fore it is switched off automatically by
pressing the button again.
1 0 . S w i t c h i n g t h e s y s t e m o f f
Press the " s m a l l f a n " button of the
a i r l o w 7 until the fan symbol disap-
pears.
This action switches off all of the
functions of the air conditioning sys-
tem, with the exception of the demist-
ing of the rear screen 9 .
Temperature related comfort is no
l o n g e r g u a r a n t e e d b u t a s l i g h t l o w o f
air, due to the movement of the ve-
hicle, can still be felt.
Pressing the " l a r g e f a n " button of
t h e a i r l o w 7 again or the AUTO but-
ton reactivates the system with the
values set before it was switched off.
Page 91 of 212
LAYOUT
81
INTERIOR LAYOUT
2. Front ashtray
Pull the lid to open the ashtray.
To empty it after opening, press the
tab and remove the ashtray.
3. Storage
4. 12 volt socket (100 W max)
T h i s i s a l i g h t e r t y p e s o c k e t , i t t e d
with a cap. It is supplied with current
from the running position.
5. Door tray
6. Storage/Can holder
7. Coin storage
8. Waste container
To empty this, open it fully (past the
point of resistance) then pull on the
receptacle to remove it.
T o r e i t , l o c k i t i n p l a c e o n t h e c o v e r .
It contains three sockets * B for con-
necting video equipment.
The layout allows storage of a water
bottle, a pen, the vehicle handbook,
a pair of spectacles, tokens, etc.
1. Glove box with cooling facility
T h i s i s i t t e d w i t h a l o c k .
T o o p e n t h e g l o v e b o x , l i f t t h e h a n d l e .
T h e g l o v e b o x l i g h t s w h e n t h e l i d i s
opened.
I t h a s a v e n t i l a t i o n n o z z l e t h a t c a n
be closed A , distributing the same
cooled air as the vents of the pas-
senger compartment.
* With colour display only.
Page 127 of 212
CHECKS
115
CHECKING THE LEVELS
There are two marks on
the dipstick:
A = maximum
N e v e r i l l p a s t t h i s m a r k .
B = minimum
Oil change
According to the information given in
the servicing booklet.
Viscosity selection
In all cases, the oil selected must
meet the manufacturer’s require-
ments.
Note: the coolant does not need to
be changed.
Dipstick
Cooling system
U s e t h e l u i d r e c o m m e n d e d b y t h e
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. This fan can oper-
ate with the ignition off.
I n t h e c a s e o f v e h i c l e s i t t e d w i t h
a p a r t i c l e e m i s s i o n i l t e r , t h e f a n
can operate after the vehicle has
s t o p p e d , e v e n w h e n t h e e n g i n e i s
cold.
In addition, as the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying out any work.
Slacken the cap by two turns to re-
lease the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and
top up the level.
Windscreen and headlamp
w a s h l e v e l
Diesel additive level (Diesel
w i t h p a r t i c l e e m i s s i o n f i l t e r )
If the service warning light comes on,
accompanied by a message and an
audible signal, this indicates a low
diesel additive level.
This additive must be topped up.
Contact a PEUGEOT dealer as soon
as possible.
Brake fluid level
* According to engine.
Oil level
To maintain the reliability of
engines and emission control
systems, the use of additives
in engine oil is prohibited.
The level should always be
above the MIN mark and
close to the MAX mark.
P o w e r s t e e r i n g r e s e r v o i r
Remove the style trim * (see §
"Changing a bulb - Front lights").
Open the reservoir, with the engine
at ambient temperature. The level
should always be above the MIN.
mark and close to the MAX. mark.
For best quality cleaning and
for your safety, we would ad-
vise that you use products
recommended by PEUGEOT.
Check the level regularly and
top up between changes. The
maximum consumption is 0.5 l
per 600 miles (1 000 km).
Check the level with the ve-
hicle level, engine cold, using the oil
level gauge on the instrument panel
or the dipstick. Replacement must be car-
ried out according to the
manufacturer’s servicing
schedule.
U s e l u i d s r e c o m m e n d e d b y
t h e m a n u f a c t u r e r , w h i c h f u l i l D O T 4
standards.
Page 151 of 212
10PRACTICAL INFORMATION
136
D r i v i n g a d v i c e
D i s t r i b u t i o n o f l o a d s :
Distribute the load in the trailer so
that the heaviest items are as close
as possible to the axle and the nose
weight approaches the maximum
permitted without exceeding it.
Cooling:
towing a trailer on a slope increases
the temperature of the coolant.
As the fan is electrically controlled,
its cooling capacity is not dependent
on the engine speed.
To lower the engine speed, reduce
your speed.
The maximum towing load on a long
slope depends on the gradient and
the outside temperature.
In all cases, pay attention to the
coolant temperature.
If the warning light comes on, stop
the vehicle and switch off the engine
as soon as possible. T y r e s :
check the tyre pressures of the towing
vehicle and of the trailer, observing
the recommended pressures.
Braking:
towing increases the
braking distance.
Lights: check the electrical
signalling on the trailer.
S i d e w i n d : take into account the
increased sensitivity to side wind.
T O W I N G A T R A I L E R , A
C A R A V A N , A B O A T , E T C . . .
Your vehicle is primarily designed
for transporting people and luggage
but it may also be used for towing a
trailer.
We recommend the use of original
PEUGEOT towbars and their
harnesses that have been tested and
approved from the design stage of
y o u r v e h i c l e a n d t h a t t h e i t t i n g o f t h e
towbar is entrusted to a PEUGEOT
dealer.
I f t h e t o w b a r i s n o t i t t e d b y a
PEUGEOT dealer, it is imperative
t h a t i t i s i t t e d u s i n g t h e e l e c t r i c a l
pre-equipment located at the rear of
the vehicle in accordance with the
manufacturer’s instructions.
Driving with a trailer subjects the
t o w i n g v e h i c l e t o m o r e s i g n i i c a n t
stress and its driver must be
particularly careful.
Air density decreases with altitude,
thus reducing engine performance.
Above 1 000 metres, the maximum
towing load must be reduced by 10 %
and so on for every 1 000 metres of
altitude.
The rear parking assistance function
will be disarmed automatically when
a t o w b a r i s i t t e d .
Page 152 of 212
10PRACTICAL INFORMATION
Saloon: w h e n i t t i n g t r a n s v e r s e r o o f
bars, use the four threads provided
for this purpose. To access these,
p u s h t h e c o n c e a l i n g l a p s i n t h e
direction of the arrow.
Estate: w h e n i t t i n g t r a n s v e r s e r o o f
bars, observe their positioning. This
is indicated by marks on each of the
longitudinal bars.
Use accessories approved by
PEUGEOT and follow the manufac-
t u r e r ’ s i t t i n g i n s t r u c t i o n s .
M a x i m u m a u t h o r i s e d w e i g h t
o n t h e r o o f r a c k , f o r a l o a d i n g
h e i g h t n o t e x c e e d i n g 4 0 c m
( w i t h t h e e x c e p t i o n o f b i c y c l e
c a r r i e r s ) : 8 0 k g ( s a l o o n ) , 1 0 0 k g ( e s -
tate).
I f t h e h e i g h t e x c e e d s 4 0 c m ,
a d a p t t h e s p e e d o f t h e v e h i c l e t o
t h e p r o i l e o f t h e r o a d t o a v o i d
d a m a g i n g t h e r o o f b a r s a n d t h e
i x i n g s o n t h e r o o f .
FITTING ROOF BARS V E R Y C O L D C L I M A T E S C R E E N *
The very cold climate screen is
installed on the lower part of the front
bumper to prevent the accumulation
of snow at the radiator cooling fan.
W h e n t h e s n o w h a s c l e a r e d
( t e m p e r a t u r e a b o v e 1 0 ° C ) , r e m o v e
t h e v e r y c o l d c l i m a t e s c r e e n .
FITTING
Offer up the very cold climate
screen facing the front bumper .
Put it in place by pressing at each
clip .
R E M O V A L
Insert a screwdriver into the hole
located near each of the clips.
Use the screwdriver as a lever to
unclip each clip in turn.
* According to country.