display Peugeot 307 CC 2003 Workshop Manual

22-09-2003
YOUR 307 CC IN DETAIL105
Automatic windscreen wipers In the
AUTOposition, the wind-
screen wipers operate automatically and adapt their speed to the inten-
sity of the rainfall.
Operating check ActivationWhen the function is activated, the message "Automatic wiping
active" appears on the multi-func-
tion display. Disarming In the event of malfunction , the dri-
ver is informed by an audible signal and the message "Auto wiper fault"
on the multi-function display. In the AUTOposition, the wind-
screen wiper will operate in intermit- tent mode.
Contact a PEUGEOT dealer to have the system checked. Do not cover the rain sen-sor located on the wind-screen behind the interior
mirror.
When using an automatic carwash, switch off the ignition orcheck that the wiper stalk is not inthe automatic position.
In winter, it is advisable to wait for the windscreen to completelyclear of ice before operating theautomatic wipe.

22-09-2003
YOUR 307 CC IN DETAIL
106
Colour screen DT
Ð the
"Current information" with:
¥ the range,
¥ the current consumption,
¥ the distance still to be driven.
Ð "Route 1" with:
¥ the distance travelled,
¥ the average consumption,
¥ the average speed,
Ð "Route 2" with the same features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-setWhen the required route is dis- played, press the button for morethan two seconds.
TRIP COMPUTER
Each time the button on the end of the wiper stalk
is pressed, the following
sequence of data is displayed:
Monochrome screen CT
Ð the "vehicle" tab with:
¥ range, current consumption and the distance still to be driven,
Ð tab "1'(route "1") with:
¥ the distance driven, the average consumption and the average speed calculated over route "1"
Ð tab "2"(route "2") with the same
features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-set When the required route is dis- played, press the button for morethan two seconds.
Monochrome screen B
Ð the remaining range
Ð the distance travelled
Ð the average consumption
Ð the current consumption
Ð the average speed In addition, it allows access to the warning log
information and to the
Excess speed warning* function.
Zero reset Press the stalk for more than two seconds.
* During the year.

22-09-2003
YOUR 307 CC IN DETAIL107
Distance remaining to be travelled This is the distance remaining to the destination. It can either be calculat-ed by the navigation if guidance is
activated, or entered by the user,minus the distance covered since thedistance was entered. Note:
if digits are missing, dashes
are displayed in their place.
Average speed This is the average speed calculated since the computer was last set tozero (with the ignition on). The warning log This summarises the active warning messages by displaying them on the
multi-function display. The excess speed warning function* This monitors the maximum speed required. In the event that the pro-grammed speed is exceeded, themessage ''Speed too high'' appears
on the multi-function display, accom-panied by an audible signal. Activation Keep pressing the control until the display indicates "Excess speed
ON" .
* During the year.
Range This shows the distance that can still be covered with the fuel remaining inthe tank. Note:
this figure may increase if
there is a change in the style of dri- ving or the road surface, producing asignificant drop in current consump-tion. If horizontal segments are displayed for long periods instead of digits,
contact a PEUGEOT dealer. Current consumption This is the average quantity of fuel consumed during the last few se-conds. This function is displayed only when the vehicle is travelling at a speedgreater than 20 mph (30 km/h).
Average consumption This is the average fuel consumption since the computer was last set tozero. Distance travelled This indicates the distance travelled since the computer was last set tozero. Programming
Press the control briefly. Accelerate to the desired speed.Keep pressing the control to store in
memory. Switching off Keep pressing the control until the display indicates
"Excess speed
OFF" .
The routes The routes "1"and "2"are indepen-
dent but have identical application.Route "1" for example allows you to
make daily calculations and route "2" monthly calculations.

22-09-2003
YOUR 307 CC IN DETAIL
106
Colour screen DT
Ð the
"Current information" with:
¥ the range,
¥ the current consumption,
¥ the distance still to be driven.
Ð "Route 1" with:
¥ the distance travelled,
¥ the average consumption,
¥ the average speed,
Ð "Route 2" with the same features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-setWhen the required route is dis- played, press the button for morethan two seconds.
TRIP COMPUTER
Each time the button on the end of the wiper stalk
is pressed, the following
sequence of data is displayed:
Monochrome screen CT
Ð the "vehicle" tab with:
¥ range, current consumption and the distance still to be driven,
Ð tab "1'(route "1") with:
¥ the distance driven, the average consumption and the average speed calculated over route "1"
Ð tab "2"(route "2") with the same
features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-set When the required route is dis- played, press the button for morethan two seconds.
Monochrome screen B
Ð the remaining range
Ð the distance travelled
Ð the average consumption
Ð the current consumption
Ð the average speed In addition, it allows access to the warning log
information and to the
Excess speed warning* function.
Zero reset Press the stalk for more than two seconds.
* During the year.

22-09-2003
YOUR 307 CC IN DETAIL107
Distance remaining to be travelled This is the distance remaining to the destination. It can either be calculat-ed by the navigation if guidance is
activated, or entered by the user,minus the distance covered since thedistance was entered. Note:
if digits are missing, dashes
are displayed in their place.
Average speed This is the average speed calculated since the computer was last set tozero (with the ignition on). The warning log This summarises the active warning messages by displaying them on the
multi-function display. The excess speed warning function* This monitors the maximum speed required. In the event that the pro-grammed speed is exceeded, themessage ''Speed too high'' appears
on the multi-function display, accom-panied by an audible signal. Activation Keep pressing the control until the display indicates "Excess speed
ON" .
* During the year.
Range This shows the distance that can still be covered with the fuel remaining inthe tank. Note:
this figure may increase if
there is a change in the style of dri- ving or the road surface, producing asignificant drop in current consump-tion. If horizontal segments are displayed for long periods instead of digits,
contact a PEUGEOT dealer. Current consumption This is the average quantity of fuel consumed during the last few se-conds. This function is displayed only when the vehicle is travelling at a speedgreater than 20 mph (30 km/h).
Average consumption This is the average fuel consumption since the computer was last set tozero. Distance travelled This indicates the distance travelled since the computer was last set tozero. Programming
Press the control briefly. Accelerate to the desired speed.Keep pressing the control to store in
memory. Switching off Keep pressing the control until the display indicates
"Excess speed
OFF" .
The routes The routes "1"and "2"are indepen-
dent but have identical application.Route "1" for example allows you to
make daily calculations and route "2" monthly calculations.

22-09-2003
YOUR 307 CC IN DETAIL
108
Trip computer configuration This function allows the distance to the destination to be input (whenguidance is not activated; otherwisethis information is given by the navi-gation system) and also changing of
the units of measurement (¡C or ¡F,km and litres or miles and gallons). Distance to destination When guidance is not activated, this enables an approximate value to beentered to make all the trip computercalculations possible.
Specific features of the monochrome screen CT and the colour screen DT General menu Press the
"MENU" button to access
the general menu.Select the icon "Trip computer"
using the dial, then validate to
access the ''Trip computer'' menu.
The ''trip computer'' menu offers var- ious choices:
Ð Trip computer configuration,
Ð Warning log.
"Trip computer" context menu The context menu associated with the "Trip Computer" application
appears as a superimposed display
when the Trip Computer is the appli-cation currently being used in the
main screen window. Briefly press the continuous applica-
tion "Trip computer" button to selectone of the following functions:
Ð Warning log,
Ð Distance to destination.

YOUR 307 CC IN DETAIL117
S
: sport programme


: snow programme
P ark: to immobilise the vehicle or start the engine ,
with the handbrake on or off.
R everse: to reverse(select this function with the vehi-
cle stationary, engine at idle).
N eutral: to start the engine and to park, with the hand-
brake on. Note: if function Nis engaged inadvertently while dri-
ving, allow the engine to return to idle before engaging function Dto accelerate.
D rive: for drivingin automatic mode.
M anual: for drivingin manual mode. Moving off
With the engine running, to move off from position
P:
 it is essential to press the
brake pedal to exit position P,
 select function R, D or M, then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
You can also move off from positionN :
 release the handbrake, with yourfoot on the brake,
 select function R, D or M, then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
WARNING When the engine is at idle, brakes not applied, if function R, D or Mis
selected the vehicle moves evenwithout the accelerator beingpressed. For this reason, do not leave chil-
dren unsupervised inside the vehicle, with the engine running .
When maintenance operations needto be carried out with the engine run-ning, apply the handbrake and selectposition P.
"PORSCHE TIPTRONIC SYSTEM" AUTOMATIC GEARBOX The four speed automaticgearbox offers a choice between the comfort of inte-
gral automatic operation , enhanced by a sportand a snow programme, or the
pleasure of manual gear changing .
Gear selection gate  Move the lever in the gate to select a function. Once the function is selected, the corresponding indicator light appears on
the instrument panel display.
22-09-2003

22-09-2003
YOUR 307 CC IN DETAIL
118
Automatic operation Automatic changing of the
four
gears :
 select function Din the gate.
The gearbox always selects the most suitable gear according to the follow-ing parameters:
Ð the style of driving,
Ð the road profile,
Ð the vehicle load. The gearbox is then operating in auto-adaptive mode, without anyaction on your part.
WARNING Never select function Nwhen the
vehicle is moving. Never select functions Por Runless
the vehicle is stationary.Never change between functions to optimise braking on a slippery sur-face. Notes For immediate maximum acceleration
without touching the gear lever, pressthe accelerator pedal down as far as
it will go (kickdown). The gearbox willautomatically change down or main-tain the gear selected until maximumengine speed is reached. When braking, the gearbox will auto- matically change down in order to
provide efficient engine braking. If you take your foot off the accelera-
tor suddenly, the gearbox will notchange to a higher gear for reasons
of safety.
Sport and snow programme In addition to the auto-adaptive pro- gramme, there are two special pro-grammes. The programme is displayed on the instrument panel screen. Sport programme  Press button Sonce the vehicle
has been started and function D
selected.
The gearbox automatically favours sporty driving and more dynamicacceleration. Snow programme This programme improves starting
and drive when traction is poor.  Press button

once the vehicle
has been started and function D
selected.
The gearbox adapts to driving on slippery roads. Note: you can return to the auto-
adaptive programme at any time.  Press button Sor

again to
switch off the programme you are in. Manual operation Manual changing of the
four gears:
 select function Min the gate,
 push the lever to the +sign to
change to a higher gear,
 pull the lever to the Ðsign to
change to a lower gear.
You can change from position D(dri-
ving in automatic mode) to position M (driving in manual mode) at any
time. Note It is only possible to change from one gear to another if the vehicle speedand engine speed permit. If they donot, the vehicle will operate tem-porarily in automatic mode. When the vehicle is stationary or
moving very slowly, the gearboxautomatically selects gear M1.
Programme S(sport) and

(snow)
do not operate in manual mode.

22-09-2003
YOUR 307 CC IN DETAIL119
Releasing Pull on the handle and press the but- ton to release the handbrake.
Illumination of this warninglight and of the STOPwarn-
ing light, accompanied byan audible signal (while thevehicle is being driven) and
the message "handbrake on" on
the multi-function display, indicatesthat the handbrake is still on or hasnot been properly released.
Operating abnormality Any operating abnormality is indicat- ed by an audible signal, accompa-nied by the message
"Automatic
gear fault" on the multi-function dis-
play, "Ð"and flashing of the Sport
and Snow warning lights on theinstrument panel. In this situation the gearbox operates in downgrade mode (locked in 3rd
gear). You may feel a substantialknock when changing from Pto R
and from Nto R(this will not cause
any damage to the gearbox). Do not exceed 60 mph (100 km/h), keeping within the limit of localspeed restrictions.
Contact a PEUGEOT dealer as soon as possible. HANDBRAKE Applying Pull the handbrake to immobilise your vehicle.
Warning:
when parking on a slope,
direct your wheels towards the pave- ment and pull the handbrake.
If the battery is flat and the lever is in position P, it will
be impossible to change toanother position.

22-09-2003
YOUR 307 CC IN DETAIL119
Releasing Pull on the handle and press the but- ton to release the handbrake.
Illumination of this warninglight and of the STOPwarn-
ing light, accompanied byan audible signal (while thevehicle is being driven) and
the message "handbrake on" on
the multi-function display, indicatesthat the handbrake is still on or hasnot been properly released.
Operating abnormality Any operating abnormality is indicat- ed by an audible signal, accompa-nied by the message
"Automatic
gear fault" on the multi-function dis-
play, "Ð"and flashing of the Sport
and Snow warning lights on theinstrument panel. In this situation the gearbox operates in downgrade mode (locked in 3rd
gear). You may feel a substantialknock when changing from Pto R
and from Nto R(this will not cause
any damage to the gearbox). Do not exceed 60 mph (100 km/h), keeping within the limit of localspeed restrictions.
Contact a PEUGEOT dealer as soon as possible. HANDBRAKE Applying Pull the handbrake to immobilise your vehicle.
Warning:
when parking on a slope,
direct your wheels towards the pave- ment and pull the handbrake.
If the battery is flat and the lever is in position P, it will
be impossible to change toanother position.