light Peugeot 407 C 2008 Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008, Model line: 407 C, Model: Peugeot 407 C 2008Pages: 211, PDF Size: 11.74 MB
Page 73 of 211
4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is rec-
ognised and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
If the system does not
f u n c t i o n c o r r e c t l y , the
warning light comes on on
the instrument panel display,
accompanied by an audible
signal and a message on the
multifunction display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work af-
ter the battery has been changed, re-
programme the remote control.
Page 75 of 211
4
68
THE ALARM
This provides two types of surveillance:
- exterior protection: it sounds if
a door, the boot or the bonnet is
opened.
- interior protection: it sounds if
the volume inside the passenger
compartment changes (breaking
of a window or a movement inside
the vehicle). When the alarm is triggered, the siren
sounds and the direction indicator lights
fl a s h f o r a p p r o x i m a t e l y t h i r t y s e c o n d s .
After triggering, the alarm remains set,
ten times in succession.
On the eleventh time it will become
inactive again, until the next cycle of
disarming then setting of the alarm.
Warning: if button A indicator light
fl a s h e s r a p i d l y , t h e a l a r m h a s b e e n
triggered while you were away from
your vehicle.
Incorrect operation
When the ignition is switched on, if
button A lights for ten seconds, there
is a fault in the siren connection.
Contact a PEUGEOT dealer to have
the system checked.
R e m o t e c o n t r o l f a i l u r e , a l a r m set
Unlock the doors with the key and
open the door. The alarm is trig-
gered.
Switch on the ignition. The alarm is
disarmed.
* According to country.
Setting the alarm
Switch off the ignition and get out
of the vehicle.
Set the alarm, by locking or dead-
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once per second).
If you wish to lock or deadlock your ve-
hicle without setting the alarm, lock it
(one turn of the key) or deadlock it (a
s e c o n d t u r n w i t h i n fi v e s e c o n d s m a x i -
mum) using the lock.
The alarm is activated automatically
two minutes after the last closure of a
door or the boot.
In order to avoid accidental triggering
of the alarm when a door or the boot
is opened, it is essential to press the
unlocking button on the remote control
again.
Before setting the alarm, en-
sure that all of the accesses
(doors, bonnet, boot) are
closed correctly.
Disarming
Unlock the vehicle with the remote
control key.
The alarm is disarmed, indicator light A
goes out when the ignition is switched on.
T o s e t t h e a l a r m w i t h e x t e r i o r protection only
If, while you are away from the vehi-
cle, you wish to leave a window par-
tially open or a pet inside the vehicle,
you should choose exterior protection
only.
Switch off the ignition,
In the next ten seconds, press but-
ton A until the indicator light is on
continuously,
Get out of the vehicle,
Set the alarm by locking or dead-
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once a second).
Page 81 of 211
4
73
FILLING WITH FUEL
T h e f u e l fi l l e r fl a p i s e l e c t r i c , y o u c a n
only open it by pressing button A .
Button A is deactivated auto-
matically from 6 mph (10 km/h).
W h e n fi l l i n g w i t h f u e l , t h e
e n g i n e m u s t b e s w i t c h e d o f f
w i t h t h e i g n i t i o n o f f : O p e r a t i n g f a u l t
A fuel gauge fault is indicated by the
fuel level indicator needle returning to
zero.
Consult a PEUGEOT dealer.
F u e l w a r n i n g
Turn the cap to the left.
Remove the cap and hang the end
on the hook located on the inside
o f t h e fl a p .
A l a b e l a f fi x e d t o t h e i n s i d e o f t h e f u e l
fi l l e r fl a p i n d i c a t e s w h i c h t y p e o f f u e l
to use.
W h e n y o u fi l l y o u r t a n k , d o n o t c o n -
tinue after the third cut-off of the pump.
This could cause your vehicle to mal-
function.
The capacity of the tank is approxi-
m a t e l y 6 7 l i t r e s .
A f t e r fi l l i n g t h e t a n k , s c r e w o n t h e
c a p a n d c l o s e t h e f u e l fi l l e r fl a p .
E n s u r e t h a t t h e f u e l fi l l e r fl a p i s
closed correctly. When this warning light comes
on in certain driving conditions
and depending on the engine,
the distance which can be
travelled with the fuel remain-
ing may be less than 30 miles
(50 kilometres).
Note: should you run out of fuel, you
must add at least 6 litres.
Page 82 of 211
5
74
LIGHTS STALK
Lights off
Side lights Dipped/main beam head-
lamps Lights on
With the ignition and the automatic
lights function switched off, on open-
ing the driver's door a buzzer sounds
to warn you that you have left your
lights on.
Front and rear fog lamps (ring B)
Turn ring B forwards to switch on
and backwards to switch off. The
p o s i t i o n i s c o n fi r m e d b y t h e l i g h t
on the instrument panel.
Front fog lamps (one press)
These operate with the side lights, dipped
headlamps or main beam headlamps. Rear fog lamps (two presses)
These operate with the side lights and
the front fog lamps, or with the dipped
or main beam headlamps.
Left
: downwards.
Right
: upwards
D i r e c t i o n i n d i c a t o r s ( fl a s h e r s )
If you forget to return the di-
rection indicator to its normal
position, the volume of the au-
dible signal will increase, if you
are driving at a speed greater
than 45 mph (70 km/h).
Parking lights *
The side lights are lit on the side the
t r a f fi c i s o n f o r a f e w h o u r s .
With the engine switched off and with-
in 45 seconds maximum, place the in-
d i c a t o r l i g h t s s t a l k o n t h e t r a f fi c s i d e
(for example: for parking on the right;
switching on of the lights on the left).
This is indicated by an audible signal
and lighting of the corresponding di-
rection indicator on the instrument
panel for a few seconds. If the parking lights are activated
when your vehicle switches to
economy mode, they will remain
on. However, you cannot acti-
vate the parking lights if your vehicle is
already in economy mode.
Dipped/main beam change
Pull the stalk fully towards you.
* According to version.
Automatic switching on of
the lights.
In the case of vehicles which
a r e n o t fi t t e d w i t h a l i g h t s s t a l k
with the "AUTO" position,
you can deactivate or activate
the automatic lighting via the multi-
function display "Personalisation -
C o n fi g u r a t i o n " menu.
Front and rear lights (ring A)
Turn ring A to the position required
Page 83 of 211
5
75
The timed duration must also
be set, via the multifunction
display "Personalisation -
C o n fi g u r a t i o n " menu.
A u t o m a t i c s w i t c h i n g o n o f t h e lights
To switch the function on
or off, use the multifunction
display "Personalisation -
C o n fi g u r a t i o n " menu. Activation
Deactivation
When this function is activat-
ed, the indicator light on the
instrument panel comes on.
When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
M a n u a l " f o l l o w - m e - h o m e " l i g h t i n g
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
A u t o m a t i c " f o l l o w - m e - h o m e "
lighting
When you leave your vehicle with
the
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
activated , the side lights and dipped
headlamps remain on for the duration se-
lected when the ignition is switched off.
To activate or deactivate this func-
tion, pass via the multifunction display
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
In foggy weather, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi -
cient light. As a consequence,
the lights will not come on au-
tomatically.
This function is active when the vehi-
cle is supplied to the customer.
If the brightness sensor does not
f u n c t i o n c o r r e c t l y , if the system is
activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes on
on the instrument panel.
* According to country.
This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.
The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.
Page 84 of 211
5
75
The timed duration must also
be set, via the multifunction
display "Personalisation -
C o n fi g u r a t i o n " menu.
A u t o m a t i c s w i t c h i n g o n o f t h e lights
To switch the function on
or off, use the multifunction
display "Personalisation -
C o n fi g u r a t i o n " menu. Activation
Deactivation
When this function is activat-
ed, the indicator light on the
instrument panel comes on.
When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
M a n u a l " f o l l o w - m e - h o m e " l i g h t i n g
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
A u t o m a t i c " f o l l o w - m e - h o m e "
lighting
When you leave your vehicle with
the
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
activated , the side lights and dipped
headlamps remain on for the duration se-
lected when the ignition is switched off.
To activate or deactivate this func-
tion, pass via the multifunction display
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
In foggy weather, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi -
cient light. As a consequence,
the lights will not come on au-
tomatically.
This function is active when the vehi-
cle is supplied to the customer.
If the brightness sensor does not
f u n c t i o n c o r r e c t l y , if the system is
activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes on
on the instrument panel.
* According to country.
This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.
The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.
Page 85 of 211
5
76
AUTOMATIC HEADLAMP ADJUSTMENT
W h e n s t a t i o n a r y a n d w h e n t h e v e h i -
cle is moving , the system automati-
cally corrects the height of the beam,
whatever the load of the vehicle. The
driver is then assured of having opti-
mum lighting and not causing a nui-
sance to other road users.
DIRECTIONAL HEADLAMPS
Activation/Deactivation
When the dipped or main beam head-
lamps are on, this function enables the
light beam to follow the direction of the
road.
The quality of your lighting when turning
is improved considerably.
I n c a s e s o f m a l f u n c t i o n ,
the warning light comes on
on the instrument panel dis-
play, accompanied by an au-
dible signal and a message
on the multifunction display. The sys-
tem places your headlamps to the low
position.
Do not touch the xenon bulbs. Consult
a PEUGEOT dealer. F u n c t i o n a c t i v a t e d
F u n c t i o n d e a c t i v a t e d To deactivate or acti-
vate the function, go to
the
"Personalisation -
C o n fi g u r a t i o n " menu on
your multifunction display.
When the engine is switched on, the
status of activation/deactivation of this
function selected when the engine was
switched off is retained.
By default, this function is activated.
Note: when stationary or driv-
ing at very low speed, or in
reverse gear, this function is
inactive.
I n t h e e v e n t o f a m a l f u n c -
tion, t h i s w a r n i n g l i g h t fl a s h e s
on the instrument panel.
O n v e h i c l e s fi t t e d w i t h d a y t i m e
lights, the function is only acti-
vated if the lights stalk is in the
dipped/main beam headlamps
position.
On starting, with the engine
running, the headlamps initial-
ise automatically and perform
a vertical sweep.
Consult a PEUGEOT dealer.
Page 86 of 211
5
77
WINDSCREEN WIPER STALK
In the Intermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In the AUTO position, no further action
on your part is required.
A u t o m a t i c w i n d s c r e e n w i p e r
The automatic wiping is controlled by a
r a i n s e n s o r , fi t t e d o n t h e w i n d s c r e e n .
In AUTO mode, the wipers operate
automatically and a d j u s t t h e i r s p e e d
t o t h e i n t e n s i t y o f t h e r a i n f a l l .
Activation Deactivation
This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver presses the
wipers stalk down in AUTO
mode. This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver moves the
wipers stalk to position
I , 1
or 2 .
I n t h e e v e n t o f a m a l f u n c t i o n , the
driver is informed of this by a message
on the multifunction display.
In AUTO mode, the wipers will then
operate in intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Do not cover the rain sensor,
located on the windscreen be-
hind the interior mirror.
When using a car wash, switch
off the ignition.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic wipers.
When parking in snowy weather, position
the blades at the top of the windscreen
(maintenance position) to prevent the ac-
cumulation of snow.
T h e w i p i n g m u s t b e r e a c t i -
vated if the ignition has been
switched off for more than one
minute . Manual operation of the wipers stalk
by moving the lever
A up and return-
ing it to position "0" cancels the AUTO
position, the deactivation warning light
comes on on the instrument panel dis-
play accompanied by a message on
the multifunction display.
W i n d s c r e e n w i p e r s
2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
I Intermittent wipe
0 Off
AUTO Automatic wipe then single
sweep.
Page 87 of 211
5
78
Maintenance position
This position enables the wiper blades
to be removed.
In the minute following switching off of
the ignition, any action on the wipers
stalk positions the wipers at the top
of the windscreen (parking in winter,
cleaning, replacement of the blades).
To reposition the wipers after this has
been done, switch on the ignition and
operate the stalk. W i n d s c r e e n a n d h e a d l a m p w a s h
Pull the windscreen wiper stalk to-
wards you. The windscreen wash then
the windscreen wipers operate for a
fi x e d p e r i o d .
The headlamp wash is also activated,
i f t h e h e a d l a m p s a r e o n .
S c r e e n w a s h / h e a d l a m p w a s h l o w
When the minimum level of
the reservoir is reached, this
warning light comes on, ac-
companied by an audible
signal and a message on the
multi-function display.
N e x t t i m e y o u s t o p , fi l l t h e s c r e e n -
wash/headlamp wash reservoir.
The warning light comes on each time
the stalk is operated, until the reser-
v o i r i s fi l l e d .
Page 88 of 211
5
77
WINDSCREEN WIPER STALK
In the Intermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In the AUTO position, no further action
on your part is required.
A u t o m a t i c w i n d s c r e e n w i p e r
The automatic wiping is controlled by a
r a i n s e n s o r , fi t t e d o n t h e w i n d s c r e e n .
In AUTO mode, the wipers operate
automatically and a d j u s t t h e i r s p e e d
t o t h e i n t e n s i t y o f t h e r a i n f a l l .
Activation Deactivation
This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver presses the
wipers stalk down in AUTO
mode. This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver moves the
wipers stalk to position
I , 1
or 2 .
I n t h e e v e n t o f a m a l f u n c t i o n , the
driver is informed of this by a message
on the multifunction display.
In AUTO mode, the wipers will then
operate in intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Do not cover the rain sensor,
located on the windscreen be-
hind the interior mirror.
When using a car wash, switch
off the ignition.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic wipers.
When parking in snowy weather, position
the blades at the top of the windscreen
(maintenance position) to prevent the ac-
cumulation of snow.
T h e w i p i n g m u s t b e r e a c t i -
vated if the ignition has been
switched off for more than one
minute . Manual operation of the wipers stalk
by moving the lever
A up and return-
ing it to position "0" cancels the AUTO
position, the deactivation warning light
comes on on the instrument panel dis-
play accompanied by a message on
the multifunction display.
W i n d s c r e e n w i p e r s
2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
I Intermittent wipe
0 Off
AUTO Automatic wipe then single
sweep.