ignition Peugeot 407 Dag 2010 Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 407 Dag, Model: Peugeot 407 Dag 2010Pages: 249, PDF Size: 14.8 MB
Page 71 of 249
4ACCESS
64
Anti-theft protection
D o n o t m a k e a n y m o d i fi c a -
tions to the electronic engine
immobiliser system; this could
cause malfunctions. CHILD LOCK
Electric mode Always remove the ignition
key when leaving the vehicle,
even for a short time.
It is advisable to check the ac-
tivation of the child lock each time the
ignition is switched on.
In the event of a serious impact, the
electric child lock is deactivated auto-
matically to permit the exit of the rear
passengers.
This prevents opening of both of the
rear doors from the inside.
With the ignition on, press the button.
A message appears on the multifunc-
tion screen.
This system is independent and does
not take the place of the central lock-
ing control in any circumstances.
This prevents each of the rear doors
from being opened from inside.
Turn the switch on the edge of the
door a quarter of a turn using the
ignition key.
Manual mode
When purchasing a second-
hand vehicle
Have the key codes memorised by a
PEUGEOT dealer, to ensure that the
keys in your possession are the only
ones which can start the vehicle. Do not throw the remote con-
trol batteries away, they con-
tain metals which are harmful
to the environment.
Take them to an approved col-
lection point.
Page 72 of 249
4ACCESS
65
ALARM
For all work on the alarm system, con-
tact a PEUGEOT dealer.
- Exterior perimeter
The system checks for opening of the
vehicle.
The alarm is triggered if anyone tries
to open a door, the boot, the bonnet...
- Interior volumetric
The system checks for any variation in
the volume in the passenger compart-
ment.
The alarm is triggered if anyone breaks
a window, enters the passenger com-
partment or moves inside the vehicle.
Self-protection function
The system checks for the
putting out of service of its
components.
The alarm is triggered if the battery, the
central control or the wires of the siren
are put out of service or damaged. Locking the vehicle with full
alarm system
Activation
Switch off the ignition and get out
of the vehicle.
Press the locking button on the re-
mote control.
The monitoring system is active: the
i n d i c a t o r l a m p o n t h e b u t t o n fl a s h e s
once per second.
After the locking button on the remote
control is pressed, the exterior perime-
ter monitoring is activated after a delay
of 5 seconds and the interior volumet-
ric after a delay of 45 seconds.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitor-
ing will be activated after a delay of
45 seconds at the same time as the
interior volumetric monitoring.
System which protects and provides a
deterrent against theft and break-ins.
It provides the following types of moni-
toring.
Deactivation
Press the unlocking button on the
remote control.
The alarm system is deactivated: the in-
dicator lamp on the button switches off.
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric pro-
tection to avoid unwanted triggering of
the alarm in certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea.
Deactivation of the interior
volumetric monitoring
Switch off the ignition.
Within ten seconds, press the but-
ton until the indicator lamp is lit
continuously.
Get out of the vehicle.
Press the locking button on the re-
mote control immediately.
The exterior perimeter monitoring alone
is activated: the indicator lamp on the
b u t t o n fl a s h e s o n c e p e r s e c o n d .
To be effective, this deactivation must
be carried out each time the ignition is
switched off.
Page 73 of 249
4ACCESS
66
Reactivation of the interior
volumetric monitoring
Press the unlocking button on the
remote control to deactivate the
exterior perimeter monitoring.
Press the locking button on the
remote control to activate all the
monitoring functions.
The indicator lamp on the button again
fl a s h e s o n c e p e r s e c o n d . Triggering of the alarm
This is indicated by sounding of the
s i r e n a n d fl a s h i n g o f t h e d i r e c t i o n i n d i -
cators for thirty seconds.
The monitoring functions remain ac-
tive until the alarm has been triggered
eleven times in succession.
When the vehicle is unlocked using
t h e r e m o t e c o n t r o l , r a p i d fl a s h i n g o f
the indicator lamp on the button in-
forms you that the alarm was triggered
during your absence. When the igni-
t i o n i s s w i t c h e d o n , t h i s fl a s h i n g s t o p s
immediately.
Failure of the remote control
To deactivate the monitoring functions:
Unlock the vehicle using the key in
the driver's door lock.
Open the door; the alarm is trig-
gered.
Switch on the ignition; the alarm
stops. The indicator lamp on the
button switches off. Locking the vehicle without
activating the alarm
Lock or deadlock the vehicle using
the key in the driver's door lock.
Malfunction
W h e n t h e i g n i t i o n i s s w i t c h e d o n , fi x e d
lighting of the indicator lamp on the
button indicates a malfunction of the
system.
Have it checked by a PEUGEOT dealer.
* According to country.
Automatic activation *
2 minutes after the last door or the
boot is closed, the system is activated
automatically.
To avoid triggering the alarm on
e n t e r i n g t h e v e h i c l e , fi r s t p r e s s t h e
unlocking button on the remote
control.
Page 74 of 249
4ACCESS
67
ELECTRIC WINDOWS
Automatic operation:
To open or close the window, press or
pull switch fully: the window opens or
closes completely when the switch is
released. Pressing the switch again
stops the movement of the window.
The electric window switches remain
operational for approximately one min-
ute after the key has been removed
from the ignition.
Once this time has elapsed, the elec-
tric windows will not operate. To re-
activate them, switch the ignition on
again.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the windows, you must re-
verse the movement of the window. To
do this, press the switch concerned.
When the driver operates the passen-
ger electric window switches, he must
ensure that no one is preventing cor-
rect closing of the windows.
The driver must ensure that the pas-
sengers use the electric windows cor-
rectly.
Be aware of children when operating
the windows. REINITIALISATION OFTHE ELECTRIC WINDOWS
Following reconnection of the battery,
the safety anti-pinch function must be
reinitialised: the safety anti-pinch func-
tion is not active during these opera-
tions.
- lower the window completely, then raise it, it will rise in steps of a few
centimetres each time the switch is
pressed. Repeat the operation un-
til the window closes completely,
- continue to press the switch for at least one second after reaching
this position, window closed.
Safety anti-pinch
When the window rises and meets an
obstacle, it stops and immediately par-
tially lowers again.
In the event of unwanted opening
of the window on closing, press the
switch until the window opens com-
pletely, then pull the switch immediate-
ly until the window closes. Continue to
hold the switch for approximately one
second after the window has closed.
The safety anti-pinch function is not
active during this operation.
Deactivating the rear window
controls
For the safety of your children, press
switch 5 to prevent operation of the rear
windows irrespective of their position.
When the button is pressed down, the
switches are deactivated. When the but-
ton is raised, the switches are active.
Manual operation:
To open or close the window, press
or pull the switch gently. The win-
dow stops as soon as the switch is
released.
1. Driver's electric window switch.
2. Passenger's electric window
switch.
3. Rear right electric window
switch.
4. Rear left electric window
switch.
5. Deactivating the rear electric
window switches (child safety).
Page 78 of 249
4ACCESS
70
Notes:
After reconnecting the battery, you
must reinitialise the safety anti-pinch:
- place the control in the maximum partial opening position (3rd notch
to the right),
- wait until the roof is in the maxi- mum partially open position,
- press the control for at least one second.
In the event of unwanted opening of
the roof on closing (for example, in the
presence of ice), and immediately af-
ter the roof stops:
- move the control to the "O" posi- tion and press the control immedi-
ately,
- continue to press the control until the roof is fully closed. SUNROOF (SALOON) Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the roof, you must reverse
the movement of the roof. To do this,
press the switch concerned.
When the driver operates the roof
switch, they must ensure that no one
is preventing correct closing of the
roof.
The driver must ensure that passen-
gers use the sunroof correctly.
Be aware of children when operating
the roof.
- To partially open the roof: Turn the switch to the right (three possible
settings).
- To open the roof completely: Turn the switch to the left (six possible
settings).
- To close it completely: Turn the switch back to position "O".
- Safety anti-pinch: When the sun- roof is closing and meets an ob-
stacle, it stops then partially opens
again.
The sunroof blind is manual.
Page 83 of 249
5
74
LIGHTING CONTROL STALK
Lighting on
With the ignition off, on opening the
driver's door an audible signal indi-
cates that you have left the lighting on
when leaving the vehicle.
Switch the lighting off. Direction indicators
Dipped/main beam change
Pull the stalk fully towards you. Front and rear foglamps (ring B)
Turn ring B forwards to switch on
and rearwards to switch off. The
s t a t u s i s c o n fi r m e d b y t h e l a m p o n
t h e i n s t r u m e n t p a n e l .
F r o n t f o g l a m p s ( t u r n o n c e )
Left: downwards. The
direction arrow indica-
t o r l a m p fl a s h e s o n t h e
i n s t r u m e n t p a n e l .
Right: upwards. The
direction arrow indica-
t o r l a m p fl a s h e s o n t h e
i n s t r u m e n t p a n e l .
If you forget to return the di-
r e c t i o n i n d i c a t o r t o i t s n o r m a l
p o s i t i o n , t h e v o l u m e o f t h e
audible signal will increase, if
you are driving at a speed greater than
4 0 m p h ( 6 0 k m / h ) o r i f t h e c o n t r o l s t a l k
i s h e l d o n f o r m o r e t h a n 2 0 s e c o n d s .
T h e s e o p e r a t e w i t h t h e s i d e l a m p s a n d
t h e d i p p e d o r m a i n b e a m h e a d l a m p s .
R e a r f o g l a m p s ( t u r n t w i c e )
These operate when the front fo-
g l a m p s a r e a l r e a d y o n .
Front and rear lamps (ring A)
Turn ring A to the position re-
quired.
A u t o m a t i c i l l u m i n a t i o n o f
h e a d l a m p s ,
Lighting off,
S i d e l a m p s ,
D i p p e d / m a i n b e a m h e a d -
l a m p s .
Model without AUTO lighting
Model with AUTO lighting
Page 86 of 249
5
7 6
MANUAL HEADLAMP ADJUSTMENT AUTOMATIC HEADLAMP ADJUSTMENT
In cases of malfunction , the
w a r n i n g l a m p c o m e s o n o n
t h e i n s t r u m e n t p a n e l s c r e e n ,
a c c o m p a n i e d b y a n a u d i b l e
s i g n a l a n d a m e s s a g e o n t h e m u l t i -
f u n c t i o n s c r e e n . T h e s y s t e m p l a c e s
y o u r h e a d l a m p s t o t h e l o w p o s i t i o n .
Do not touch the xenon bulbs. Consult
a PEUGEOT dealer.
Daytime running lamps *
On vehicles which are equipped with day-
t i m e r u n n i n g l a m p s , t h e d i p p e d b e a m h e a d -
l a m p s c o m e o n w h e n t h e v e h i c l e i s s t a r t e d .
T h i s i n d i c a t o r l a m p c o m e s o n o n
t h e i n s t r u m e n t p a n e l s c r e e n .
T h e i n s t r u m e n t s a n d c o n t r o l s
( m u l t i f u n c t i o n s c r e e n , a i r c o n -
d i t i o n i n g c o n t r o l p a n e l . . . ) a r e
only lit on switching to the
a u t o m a t i c i l l u m i n a t i o n o f h e a d l a m p s
m o d e o r w h e n t h e l i g h t i n g i s s w i t c h e d
o n m a n u a l l y .
* According to country. F o r v e h i c l e s fi t t e d w i t h h a l o g e n b u l b s ,
depending on the load in your vehicle,
a d j u s t i n g t h e b e a m o f y o u r h e a d l a m p s
i s r e c o m m e n d e d .
0. 1 o r 2 p e o p l e i n t h e f r o n t s e a t s .
-. 3 people.
1. 5 people.
-. I n t e r m e d i a t e a d j u s t m e n t
2. 5 p e o p l e + m a x i m u m a u t h o r i s e d
loads.
-. I n t e r m e d i a t e a d j u s t m e n t
3. D r i v e r + m a x i m u m a u t h o r i s e d
loads.
Initial setting is position 0.
When stationary with the ignition
on , t h e s y s t e m a u t o m a t i c a l l y c o r r e c t s
t h e h e i g h t o f t h e b e a m , w h a t e v e r t h e
load of the vehicle. The driver is then
a s s u r e d o f h a v i n g o p t i m u m l i g h t i n g
and not causing a nuisance to other
road users.
Page 87 of 249
5
77
WINDSCREEN WIPER CONTROL STALK
Windscreen wiper with intermittent
wipe Windscreen wiper with automatic
wipe
The windscreen wiping
must be reactivated if the
ignition has been switched off
f o r m o r e t h a n o n e m i n u t e .
2 F a s t w i p e ( h e a v y r a i n ) .
1 N o r m a l w i p e ( m o d e r a t e r a i n ) .
l I n t e r m i t t e n t w i p e .
0 Off.
S i n g l e w i p e ( p r e s s d o w n w a r d s ) .
I n t h e I n t e r m i t t e n t p o s i t i o n , t h e w i p i n g
speed is in proportion to the vehicle
speed.
2 F a s t w i p e ( h e a v y r a i n ) .
1 N o r m a l w i p e ( m o d e r a t e r a i n ) .
AUTO A u t o m a t i c w i p e .
0 Off.
S i n g l e w i p e ( p r e s s d o w n w a r d s ) .
In the AUTO position, no action on
your part is necessary.
2 F a s t w i p e ( h e a v y r a i n ) .
1 N o r m a l w i p e ( m o d e r a t e r a i n ) .
I I n t e r m i t t e n t w i p e .
0 Off.
Windscreen wiper with Intermittent
and automatic wipe
The windscreen wiping
must be reactivated if the
ignition has been switched off
f o r m o r e t h a n o n e m i n u t e . A u t o m a t i c , t h e n s i n g l e w i p e
( s e e f o l l o w i n g p a g e ) .
In the AUTO position, no action on
your part is necessary.
I n t h e I n t e r m i t t e n t p o s i t i o n , t h e w i p i n g
speed is in proportion to the vehicle
speed.
Page 88 of 249
5
78
Automatic rain sensitive
windscreen wipers
Activation REAR WIPER CONTROL (407 SW)
Deactivation
Do not cover the rain sensor
located on the windscreen be-
h i n d t h e r e a r v i e w m i r r o r .
W h e n u s i n g a n a u t o m a t i c c a r
wash to wash your vehicle, switch off
the ignition or check that the wiper
s t a l k i s n o t i n t h e a u t o m a t i c p o s i t i o n .
In winter, it is advisable to wait for the
w i n d s c r e e n t o c o m p l e t e l y c l e a r o f i c e
b e f o r e o p e r a t i n g t h e a u t o m a t i c w i p e r s . Automatic rear wiper
If the windscreen wipers control is ac-
tivated and you engage reverse gear,
t h e r e a r w i p e r o p e r a t e s i n i n t e r m i t t e n t
m o d e .
Note: if a bicycle carrier is
used, deactivate this function
by going to the "personalisa-
t i o n - c o n fi g u r a t i o n " m e n u o n
t h e m u l t i f u n c t i o n s c r e e n o r i n s t a l l a
special bicycle carrier approved by
PEUGEOT.
T u r n t h e r i n g t o t h e fi r s t n o t c h f o r i n t e r -
m i t t e n t w i p i n g .
The control must be reactivated if
the ignition has been switched off.
T o d o t h i s , m o v e t h e c o n t r o l t o a n y
position then return it to the required
position.
Move the control to position
0 then re-
turn it to the AUTO position.
A n i n d i c a t o r l a m p c o m e s o n o n t h e i n -
s t r u m e n t p a n e l s c r e e n , a c c o m p a n i e d
b y a m e s s a g e o n t h e m u l t i f u n c t i o n
screen.
In the AUTO position, the windscreen
w i p e r s o p e r a t e a u t o m a t i c a l l y a n d
adapt their speed to the intensity of
the rainfall.
C o n t r o l w i t h a u t o m a t i c w i p i n g o n l y
In the event of malfunction , the
windscreen wipers will operate in in-
t e r m i t t e n t m o d e .
Contact a PEUGEOT dealer to have
t h e s y s t e m c h e c k e d .
C o n t r o l w i t h I n t e r m i t t e n t a n d a u t o m a t i c w i p i n g
Manual operation of the wiper stalk in-
terrupts the AUTO position, the deacti-
v a t i o n i n d i c a t o r l a m p c o m e s o n o n t h e
i n s t r u m e n t p a n e l s c r e e n , a c c o m p a -
n i e d b y a m e s s a g e o n t h e m u l t i f u n c -
tion screen. Manual operation of the wiper stalk by
m o v i n g t h e s t a l k
A up and returning
it to position "0" interrupts the AUTO
position, the deactivation indicator
l a m p c o m e s o n o n t h e i n s t r u m e n t p a n -
e l s c r e e n , a c c o m p a n i e d b y a m e s s a g e
o n t h e m u l t i f u n c t i o n s c r e e n .
Page 89 of 249
5
78
Automatic rain sensitive
windscreen wipers
Activation REAR WIPER CONTROL (407 SW)
Deactivation
Do not cover the rain sensor
located on the windscreen be-
h i n d t h e r e a r v i e w m i r r o r .
W h e n u s i n g a n a u t o m a t i c c a r
wash to wash your vehicle, switch off
the ignition or check that the wiper
s t a l k i s n o t i n t h e a u t o m a t i c p o s i t i o n .
In winter, it is advisable to wait for the
w i n d s c r e e n t o c o m p l e t e l y c l e a r o f i c e
b e f o r e o p e r a t i n g t h e a u t o m a t i c w i p e r s . Automatic rear wiper
If the windscreen wipers control is ac-
tivated and you engage reverse gear,
t h e r e a r w i p e r o p e r a t e s i n i n t e r m i t t e n t
m o d e .
Note: if a bicycle carrier is
used, deactivate this function
by going to the "personalisa-
t i o n - c o n fi g u r a t i o n " m e n u o n
t h e m u l t i f u n c t i o n s c r e e n o r i n s t a l l a
special bicycle carrier approved by
PEUGEOT.
T u r n t h e r i n g t o t h e fi r s t n o t c h f o r i n t e r -
m i t t e n t w i p i n g .
The control must be reactivated if
the ignition has been switched off.
T o d o t h i s , m o v e t h e c o n t r o l t o a n y
position then return it to the required
position.
Move the control to position
0 then re-
turn it to the AUTO position.
A n i n d i c a t o r l a m p c o m e s o n o n t h e i n -
s t r u m e n t p a n e l s c r e e n , a c c o m p a n i e d
b y a m e s s a g e o n t h e m u l t i f u n c t i o n
screen.
In the AUTO position, the windscreen
w i p e r s o p e r a t e a u t o m a t i c a l l y a n d
adapt their speed to the intensity of
the rainfall.
C o n t r o l w i t h a u t o m a t i c w i p i n g o n l y
In the event of malfunction , the
windscreen wipers will operate in in-
t e r m i t t e n t m o d e .
Contact a PEUGEOT dealer to have
t h e s y s t e m c h e c k e d .
C o n t r o l w i t h I n t e r m i t t e n t a n d a u t o m a t i c w i p i n g
Manual operation of the wiper stalk in-
terrupts the AUTO position, the deacti-
v a t i o n i n d i c a t o r l a m p c o m e s o n o n t h e
i n s t r u m e n t p a n e l s c r e e n , a c c o m p a -
n i e d b y a m e s s a g e o n t h e m u l t i f u n c -
tion screen. Manual operation of the wiper stalk by
m o v i n g t h e s t a l k
A up and returning
it to position "0" interrupts the AUTO
position, the deactivation indicator
l a m p c o m e s o n o n t h e i n s t r u m e n t p a n -
e l s c r e e n , a c c o m p a n i e d b y a m e s s a g e
o n t h e m u l t i f u n c t i o n s c r e e n .