boot Peugeot 508 2012 User Guide

50
!
Access
System which protects and provides a deterrentagainst theft and break-ins. It provides the
following types of monitoring:






Alarm
- Exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot or the bonnet...


- Interior volumetric
The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compar tment or moves inside the vehicle.

- Tilt

The system checks for any change in
the attitude of the vehicle.
The alarm is triggered if the vehicle is lifted,
moved or knocked.


Self-protection function
The system checks for the putting out of ser vice of its components. The alarm is triggered if the battery,the central control unit or the wires of the siren are put out of ser vice or damaged.

For all work on the alarm system, contact a PEUGEOT dealer or a qualified workshop.


Locking the vehicle with full
alarm system


Activation
)Switch off the ignition and get out of the vehicle.
)
Press the locking button on theremote control or lock the vehicle
using the Keyless Entry and Starting system. The monitorin
g system is active: the indicator
lamp on the button flashes once per second.

After the locking button on the remote controlis pressed or the vehicle locked using the
Ke
yless Entry and Starting system, the exterior perimeter monitoring is activated after a delay
of 5 seconds, the interior volumetric monitoring
after 45 seconds and anti-tilt monitoring after 90 seconds.
If an opening (door, boot...) is not closed
fully, the vehicle is not locked but the exterior perimeter monitoring will be activated after a
delay of 45 seconds.
) Press the unlocking button on
the remote control or unlock the
vehicle using the Keyless Entryand Star ting system.

Deactivation of the volumetric monitoring

The volumetric protection system is
deactivated: the indicator lamp in the
button
goes off.

2
51
Access

Locking the vehicle
w
ith exterior perimeter
monitoring only
Deactivate the interior volumetric and anti-liftmonitoring to avoid unwanted triggering of the alarm in certain cases such as:


- leaving a window par tially open,

- washing your vehicle,

- changing a wheel,

- having your vehicle towed,

- transportation by sea.


Deactivation of the interior volumetric and anti-tilt monitoring
)
Switch of the ignition and within
ten seconds, press this button
until the indicator lamp is on
continuously.) Get out of the vehicle.
)
Press the locking button on
the remote control immediatelyor lock the vehicle using the
Keyless Entry and Starting system.
The exterior perimeter monitorin
g alone is
activated: the indicator lamp in the button
flashes once per second.
To b e effective, this deactivation must be carried
out each time the ignition is switched off.
Reactivation of the interior volumetric and anti-tilt monitoring
Tr iggering of the alarm
This is indicated by sounding of the siren andflashing of the direction indicators for thirty seconds.
The monitoring functions remain active until
the alarm has been triggered eleven times insuccession.
) Press the unlocking button on
the remote control or unlock thevehicle using the Keyless Entry
and Star ting system to deactivate
the exterior perimeter monitoring.
) Press the locking button on the
remote control or lock the vehicleusing the Keyless Entry and Starting system to activate all the monitoring functions.

The indicator lamp in the button
again flashes once per second.


When the vehicle is unlocked usingthe remote control or unlocked
using the Keyless Entry and Starting
system, rapid flashing of the indicator lamp in the button informs you that the alarmwas triggered during your absence. When
the ignition is switched on, this flashing stopsimmediately.

Failure of the remote control

To deactivate the monitoring functions:
)
Unlock the vehicle using the key in thedriver's door lock. )
Open the door; the alarm is triggered. )
Switch on the ignition; the alarm stops.
The indicator lamp in the button switches off.




Locking the vehicle without
activating the alarm
)
Lock or deadlock the vehicle using the key
in the driver's door lock.




Operating fault


When the ignition is switched on, fixed
illumination of the indicator lamp in the button
indicates a fault in the system.
Have it checked by a PEUGEOT dealer or a qualified workshop.


* Accordin
g to country.


Automatic activation *


2 minutes after the last door or the boot is closed, the system is activated automatically. )
To avoid triggering the alarm on enteringthe vehicle, first press the unlocking button on the remote control or unlock the vehicleusing the Keyless Entry and Star ting system.

54
Access











Boot
Saloon
)After unlocking the vehicle completely using the remote control or the key, press
this button.



SW
)
After unlocking the vehicle completelyusing the remote control or the key, press
at the top (on lever A ), and raise theAtailgate.

From the inside

Hold this button down until unlocking of theboot is heard.
Opening


Closing
)Lower the tailgate using the interior grabhandle.
If the tailgate is not closed correctly:


- when the en
gine is running
,
this warning lamp and amessage in the instrument panelscreen appear for a few seconds,
-when the vehicle is moving(speed above
6 mph (10 km/h)), this warning lamp and a message, accompanied by an audiblesignal, appear in the instrument panel
screen for a few seconds.

56
!
Access
) Press this button C
to close thetailgate electrically.
Do not hinder closin
g of the tailgate: any
obstacle to closing causes the tailgate to stopand rise a few centimetres automatically.To close the tailgate manually: move the
tailgate slightly up then down to disengage it
from its drive then lower it until closed.
To avoid the risk of injury, ensure
that no one is close to the rear of thevehicle when opening or closing the tailgate.

While electric opening or closing of the tailgate
is in progress, you can stop its movement at
an
y time: ) press the interior button or button A
on
the remote control or button Bor C on thetailgate.


Stopping the opening or
closing
Ad
justing the opening
height

The maximum opening height of the tailgate can be set and memorised (restricted overheadclearance, ...).
This memorisation is done in two steps,by successive presses on button C
:


- during opening, a first press stops the
tailgate at the desired height,

- a second maintained press memorises the
position of the tailgate; an audible signal confirms the memorisation.
To delete this memorisation, make a newmaintained press until the audible signal isheard.
"Boot open" warning
With the engine running or when the vehicle ismoving, if the tailgate is not properly closed,
a message accompanied by an audible signal
(from 6 mph (10 km/h)) is displayed in the
instrument panel screen.

2
57
Access
Emergency release
(Saloon and SW)
System for mechanical unlocking of the boot in
the event of a battery or central locking fault.
Unlocking
)Fold back the rear seats to gain access to
the lock from inside the boot.)Insert a small screwdriver into hole Aof
the lock, then move the lever to the le
ft tounlock the boot.

3
69
!
Comfort











Rear seats
Bench seat the left-hand (1/3) or right-hand (2/3) section of which can be folded to adapt the boot load space.


Outer rear seat head restraints

These have a high position (comfort and safety), a low position (rear visibility) and can also be removed.
T
o remove a head restraint: )pull the head restraint fully upwards, )then, press the lug A .

Never drive with rear passengers when the head restraints are removed; thehead restraints must be in place and in the high position.
Folding the seat from
the boot
)
Check that nothing is preventing the seat back from folding (head restraint, seat belts, ...),)
check also that no object on or under theseat could hinder its movement,
)
pull the control from the boot and push the seat backrest.

(SW)

Each section of the bench seat (1/3 or 2/3) hasits own control to release the seat back and its
seat cushion from the boot.

76
i
Comfort











Peugeot Connect USB


This connection box, consisting of a JACK
auxiliary socket and a USB port, is located in
the front armrest (under the cover).
It permits the connection of por table device,
such as a di
gital audio player of the iPod® type®
or a USB memory stick.
It reads the audio file formats (MP3, OGG,
WMA , WAV, ...) which are transmitted to your
audio equipment and played via the vehicle's
speakers.
You can mana
ge these files using the steering
mounted controls or the audio system control
panel and displa
y them in the instrument panel screen.
When the USB por t is used, the por table device
charges automatically.


For more information on the use of this system, refer to the "Audio andTelematics" section.
Ski flap
Device for storing and transporting longobjects.
Opening
)Lower the armrest. )Press the flap opening control.)Lower the flap.)Load the objects from inside the boot.

3
77
Comfort

















Boot fi ttings (Saloon)
1.Retractable hooks2.Storagepockets
With towing eye, a wheel chock and a
temporary puncture repair kit (according to
destination country and equipment).3.Stowing rings4.Retaining straps5.Boot lamp6.Boot floor
For access to the storage compar tments or
the spare wheel (according to destinationcountry), raise the floor .7.Adjustable divider

78
Comfort

















Boot fi ttings (SW)
1.Boot lamps2.Rear seats folding controls3.Retractable hooks
4.12 V accessory socket (120 W max)5.StoragepocketsWith towing eye, a wheel chock and a
temporary puncture repair kit (according to
destination country and equipment).
6.Stowing rings7.Load space cover(see following page) .
8.Boot floorFor access to the storage compar tmentsor the spare wheel (according to destinationcountry), position the floor ver tically in its guide.

80
!
i
Comfort








Warning triangle (stowing)

Before leaving your vehicle to set upand install the triangle, put on your high visibility vest.
The dimensions o
f the triangle (once folded) or its storage box must be:- A: length = 438mm,-
B: height = 56
mm,
- C: width = 38mm.
To use the triangle, refer to the manufacturer's
instructions.

Saloon
)
Press the lug 1
and pull the assembly
towards you.

SW
)
Turn the knob 2to remove the cover.)
Hold the cover and the triangle so that they do not fall.

The location for a folded trian
gle is in the inner
trim panel of the boot lid. Placing the triangle in
t
he road
Distance from your vehicle (in metres)
Road
Motorway
DayNight
50 m 80 m
150 m
These are the internationally recognisedvalues.
Use the triangle in line with local driving regulations.

The trian
gle is available as an accessory, contact a PEUGEOT dealer or a qualified
workshop.
)Place the triangle at a distance behind
t
he vehicle, as shown in the table below, according to the type of road and the level
of ambient light.