bulb Peugeot Bipper 2015 User Guide

139
Bipper_en_Chap07_accessoire_ed02-2014
ROOF RACK AND ROOF BARS
to install the transverse roof bars or a
roof rack, use the fixings provided for this
purpose.
Maximum load: 75 kg.
OTHER ACCESSORIES
A wide range of accessories and genuine
parts is offered by the P euge O t
network.
t

hese accessories and parts have been
tested and approved both for reliability and
for safety.
t

hey all benefit from P euge O t 's
recommendation and warranty.
Never exceed the gross vehicle
weight (
g
VW).
Range of professional equipment
the replacement parts department publishes
an accessory catalogue of fering various
equipment and fittings, such as:
-

wooden protective floor
, non-slip wooden
floors, wooden side protectors, glass
protection grilles,
-

roof rack, set of transverse roof bars,

loading roller,
-

towbars, towbar harnesses with

7/13
sockets, 7/7 sockets, 13 socket...
t
he fitting of electrical equipment or
accessories not listed by P euge O t

may result in the failure of your vehicle's

electronic system or high consumption.
Please note this specific warning. You
are advised to contact a representative
of P euge O t
to be shown the range of

recommended equipment and accessories.
Depending on the country in which the
vehicle is sold or operated, it may be
compulsory to have a high visibility vest,
warning triangle, replacement bulbs and
fuses available in the vehicle.
Before installing accessory radio
communication transmitters with
external aerial on your vehicle, you can
contact a P
euge O t
dealer
, who will provide
the specification (frequency band, maximum
output power, aerial position, specific
installation conditions) of the transmitters
which can be fitted, in accordance with the
Motor Vehicle
e lectromagnetic Compatibility
Directive (2004/104/
e C).
When fitting a towbar and harness
outside the P
euge O t
dealer

network, the installation must be done
using the electrical pre-equipment on the
vehicle and following the manufacture's
recommendations.
7
ACCESSORIES
Equipment

161
Bipper_en_Chap09_aide-rapide_ed02-2014
Front lamps
Open the bonnet. to access the bulbs, reach
behind the headlamp unit.
Remove the protective covers to gain
access to the bulbs.
Carry out the operations in reverse order to
refit each bulb.
CHANGING A BULB
Types of bulb
Various types of bulb are fitted on your
vehicle.
to remove them:
1.


T
ype A


e ntirely glass bulb: pull gently as it is
fitted by pressure.
2.

T
ype B
Bayonet bulb: press on the bulb then turn


it anticlockwise.
3.

T
ype C
Cylindrical bulb: move aside the contacts.
4.


T
ype D - E
Halogen bulb: release the retaining


spring from its housing.
High pressure washing
When using this type of washing on
stubborn dirt, do not persist very long on
the headlamps, or on other lamps and their
edges to avoid damaging their coating and
seals.
9
QUICK HELP
Changing a bulb

162
Bipper_en_Chap09_aide-rapide_ed02-2014
1 - Dipped beam headlamps
T
ype D, H4 - 55 W
-

Remove the cover by turning it

anticlockwise.
-

Disconnect the electrical connector
.
-

Release the retaining spring by pressing

on the two clips.
-

Change the bulb taking care to align the

metal part with the grooves on the lamp.
2 - Sidelamps
T

ype A, W 5 W - 5 W
-

Remove the cover by turning it

anticlockwise.
-

Pull the bulb holder to gain access to the

bulb.
-

Change the bulb. 3 - Main beam headlamps
T

ype D, H4 - 55 W
-

Remove the cover by turning it

anticlockwise.
-

Disconnect the electrical connector
.
-

Release the retaining spring by pressing

on the two clips.
-

Remove the bulb holder
.
-

Change the bulb taking care to align the

metal part with the groove on the lamp. 4 - Direction indicators
T

ype B, PY 21 W - 21 W amber
- t
urn the bulb holder a quarter turn

anticlockwise.
-
Remove the bulb by pressing it lightly

while turning it anticlockwise.
-
Change the bulb.
If you encounter any dif
ficulty, consult a
P euge O t
dealer or a qualified workshop.
When each operation has been

completed, check the operation of the
lamps.
5 - Foglamps
T

ype E, H1 - 55 W
Contact a P
euge O t
dealer or a qualified

workshop.
Changing a bulb

163
Bipper_en_Chap09_aide-rapide_ed02-2014
Front/rear courtesy lamps
Type C, 12 V 10 W - 10 W
-
Release the courtesy lamp using a

screwdriver.
-

Remove the cover to gain access to

the bulb.
-

Change the bulb moving aside the

two contacts.
-
e nsure that the new bulbs are secured
correctly between the two contacts.
-

Close the protective flap.
-


Fix the courtesy lamp in its housing and

ensure that it is secured correctly.
Direction indicator side repeaters
Type A, WY 5 W - 5 W amber
-
Push the repeater rearwards and
release it.
-

Support the connector and turn the bulb

holder a quarter of a turn to the left.
-
t
urn the bulb a quarter of a turn to

the left.
-

Pull the bulb then change it.
-


When refitting, engage the repeater

rearwards then move it forwards.
9
QUICK HELP
Changing a bulb

164
Bipper_en_Chap09_aide-rapide_ed02-2014
Rear lamps
- Identify the faulty bulb then open the rear
doors.
-
u nscrew the two screws using the
screwdriver supplied in the tool kit
(behind the driver's seat) and extract the
bulb holder.
-

Release the lamp unit.
-


Disconnect the electrical connector
.
-

Remove the support by moving aside the

tabs.
-

Change the bulb.
Number plate lamps
Type A, C 5 W - 5 W
- u nclip the transparent cover using
the screwdriver supplied in the tool kit
(behind the driver's seat) and extract the
bulb holder.
-

Change the bulb by moving aside the two

contacts.
-
e nsure that the new bulbs are secured
correctly between the two contacts.
-

Replace the plastic lens and press on it.
For further information concerning the bulbs,


refer to the table "
t
ypes of bulb".
1.


Brake lamps


T

ype B, P21 W - 21 W
2.

Direction indicators


T

ype B, PY 21 W - 21 W amber
3.

Reversing lamps


T

ype B, P21 W - 21 W
4.

Sidelamps/Foglamps


T

ype B, P4/21

W - 4

W/21

W On the hinged rear doors On the tailgate
Changing a bulb

165
Bipper_en_Chap09_aide-rapide_ed02-2014
Third brake lamp
On the hinged rear doors
Type B, W 5 W - 5 W (4 bulbs)
- u nclip the transparent cover using the
screwdriver located in the tool kit.
-

Disconnect the electrical connector
.
-

Remove the bulb holder by squeezing the

two tabs.
-

Remove the faulty bulb.
-


Change the bulb. On the tailgate
T

ype B, W5W - 5W (5 bulbs)
-

Open the tailgate.
-


Remove the two cover retaining screws,

then the cover.
-

Remove the bulb holder by squeezing the

two tabs.
-

Remove the faulty bulb.
-


Change the bulb.
If you encounter any dif

ficulty, consult a
P
euge O t
dealer or a qualified workshop.
9
QUICK HELP
Changing a bulb