Spare tyre Peugeot Boxer 2012 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2012, Model line: Boxer, Model: Peugeot Boxer 2012Pages: 184, PDF Size: 4.88 MB
Page 21 of 184
19
Limit the causes of excessconsumption
Spread loads throughout the vehicle;
place the heaviest items in the bottom of
the boot, as close as possible to the rear
seats.
Limit the loads carried in the vehicle and
reduce wind resistance (roof bars, roof
rack, bicycle carrier, trailer...). Use a roof
box in preference.
Remove roof bars and roof racks after use.
At the end of winter, remove snow tyres
and refit your summer tyres.
Observe the recommendations on maintenance
Check the tyre pressures regularly, when
cold, referring to the label in the door
aperture, driver's side.
Carry out this check in particular:
- before a long journey,
- at each change of season,
- after a long period out of use.
Don't forget the spare wheel and the tyres
on any trailer or caravan.
Have your vehicle serviced regularly (engine
oil, oil filter, air filter...) and observe the
schedule of operations recommended by the
manufacturer.
When refuelling, do not continue after
the 3 rd cut-off of the nozzle to avoid any
overflow.
At the wheel of your new vehicle, it is only
after the fi rst 1 800 miles (3 000 kilometres)
that you will see the fuel consumption
settle down to a consistent average.
Page 148 of 184
14
6
Changing a wheel
6. REFITTING THE REPAIREDWHEEL
Refitting of the wheel is identical to step 5,
do not forget to refit the wheel trim.
Refer to the "Identification markings"
section of chapter 9 to locate the tyre
label.
The spare wheel is not designed to be used
over long distances. Have the tightening of
the bolts and pressure of the spare wheel
checked by a PEUGEOT dealer without
delay.
Also, have the original wheel repaired and
refitted by a PEUGEOT dealer as soon as
possible.
5. FITTING THE SPARE WHEEL
- Put the wheel in place on the hub and
start screwing in the bolts by hand.
- Carry out an initial tightening of the bolts
using the wheelbrace E
.
- Lower the vehicle completely by folding
the jack, then remove the jack.
- Tighten the bolts again using the
wheelbrace E
, tighten them fully without
forcing them.
- Stow the wheel to be repaired at the
rear of the vehicle.
- Hook the support H
and screw in the
handle G
.
- Insert the socket A
in the hole then
screw in the bolt, using the ratchet
wrench B
, to raise the wheel.
- Stow the tools and the trim.
Never go underneath a vehicle
supported only by a jack (use an
axle stand).
The jack and the tool kit are specific to
your vehicle. Do not use them for other
purposes.
Page 175 of 184
17
3
Exterior
10
VISUAL SEARCH
EXTERIOR
Rear lamps, direction indicators,
3rd brake lamp,
foglamps 34, 42, 149, 152 Left-hand side:
fuel fi ller cap, fuel tank 141
Fuel cut-off 141
Load space 70-71
Rear doors 26
Number plate lamp 152
Parking sensors 78
Spare wheel, jack,
changing a wheel, tools,
puncture repair kit 144-148
Infl ating, pressures 172
Towing, lifting 158
Towbar, towball 130-131 Dimensions 160-166
Accessories 132-133
Roof bars 132
Brakes, pads 136, 138
ABS, Electronic brake force
distribution 112
EBA 112
ASR, ESP 113-114
Tyres, pressures 172
Pneumatic suspension 81 Key, remote control, battery 20-22
Starting 39-40
Central locking 27
Confi dential card 23
Alarm 24
Wiper blade 157
Door mirror 72
Side repeater 151
Front lamps, foglamps,
direction indicators 149-151
Headlamp beam height adjustment 44
Headlamp wash 45
Changing bulbs 149-151
Opening/closing doors 25-27
Key 22
Opening the bonnet, stay 134
Mode - autoclose 76