remote control PEUGEOT RCZ 2012 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2012, Model line: RCZ, Model: PEUGEOT RCZ 2012Pages: 336, PDF Size: 14.1 MB
Page 60 of 336
58
OPERATING FAULT
LOCKING THE VEHICLE WITHOUT ACTIVATING
THE ALARM
)
Lock or deadlock the vehicle using the key in the driver's door lock.
When the ignition is switched on, fi xed illumination of the indicator lamp
in the button indicates a fault with the system.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
FAILURE OF THE REMOTE CONTROL
To deactivate the monitoring functions:
)
unlock the vehicle using the key in the driver's door lock,
)
open the door; the alarm is triggered,
)
switch on the ignition; the alarm stops; the indicator lamp in the
button goes off.
TRIGGERING OF THE ALARM
The monitoring functions remain active until the alarm has been
triggered eleven times in succession.
When the vehicle is unlocked using the remote control, rapid
fl ashing of the indicator lamp in the button informs you that the
alarm was triggered during your absence. When the ignition is
switched on, this fl ashing stops immediately.
This is indicated by sounding of the siren and fl ashing of the direction
indicators for thirty seconds.
2 minutes after closing the last door or the boot, the system is activated
automatically.
)
To avoid triggering the alarm when entering the vehicle, fi rst press
the remote control unlocking button.
AUTOMATIC ACTIVATION *
* Depending on country of sale.
Page 63 of 336
2/
ACCESS
DOORS
OPENING
From outside
)
After unlocking the vehicle completely using the remote control or
the key, take hold of the door handle then pull it.
The window lowers automatically by a few millimetres to permit
opening of the door.
In freezing conditions, the presence of ice may hinder the automatic
partial opening of the window; remove the ice which may have formed
along the lower seal, located at the base of the window.
When the selective unlocking is activated, the fi rst press of the
remote control unlocking button permits unlocking of the driver's
door only.
From inside
)
Pull the door control to open the door; this unlocks this vehicle
completely.
The window lowers automatically by a few millimetres to permit
opening of the door.
With the selective unlocking activated:
- the driver's door control unlocks the driver's door and the fuel
fi ller fl ap only.
- the passenger's door control unlocks the passenger's door
and the boot.
The interior door controls do not operate when the vehicle is
deadlocked. If you leave the door open for more than one minute, the window
rises again.
Pull the handle again to reactivate the system.
Page 64 of 336
62
CLOSING
The window rises automatically after a few seconds and adjusts to
provide perfect sealing when closed.
- when the engine is running
, this warning lamp comes on,
accompanied by a message in the screen for a few seconds,
CENTRAL LOCKING CONTROL
This control permits simultaneous locking or unlocking of the doors,
boot lid and fuel fi ller fl ap from inside the vehicle.
Locking
)
Press this button to lock the vehicle.
The red indicator lamp on the button comes on.
If one of the doors or the boot lid is open, the central locking from
the inside does not take place.
Unlocking
)
Press this button again to unlock the vehicle.
The red indicator lamp on the button goes off.
Locking / deadlocking from the outside
When the vehicle is locked or deadlocked from the outside, the
red indicator lamp fl ashes and the button is inactive.
)
With normal locking, pull on the interior door control lever to
unlock the vehicle.
)
With deadlocking, you have to use the remote control or the
key to unlock the vehicle.
When washing your vehicle:
- fi rst lock the vehicle using the remote control or the key,
- avoid spraying the upper part of the windows,
- keep the end of the high pressure nozzle at least 1 metre from
the windows and door seals.
When a door is not closed correctly: Be aware of the risk of pinching when the window rises
automatically on closing the door.
- when the vehicle is moving
(speed higher than 6 mph (10 km/h)),
this warning lamp comes on, accompanied by an audible signal and
a message in the screen for a few seconds.
Page 66 of 336
64
BOOT
OPENING
)
Press this button for more than two seconds to unlock
the boot lid. The boot lid opens slightly.
)
Lift the boot lid.
This action also unlocks the doors and the fuel fi ller fl ap.
Using the manual control; vehicle unlocked
)
Press the opening control above the number plate.
)
Lift the boot lid.
CLOSING
)
Lower the boot lid using one of the interior grab handles.
)
If necessary, press the top of the boot lid to close it fully.
If the boot lid is not closed correctly:
- when the engine is running
, this warning lamp comes on,
accompanied by a message in the screen for a few seconds,
When selective unlocking is activated, the boot can also be
opened by a second press on the open padlock on the remote
control.
Using the remote control
Emergency locking
If the central locking system fails (fl at battery), you are advised to
disconnect the battery.
- when the vehicle is moving
(speed above 6 mph (10 km/h)), this
warning lamp comes on, accompanied by an audible signal and a
message in the screen for a few seconds.
Page 73 of 336
3/
EASE OF USE and COMFORT
Folding
)
From outside: lock the vehicle using the remote control or the key.
)
From inside: with the ignition on, pull the control A
in the central
position rearwards.
If the mirrors are folded using control A
, they will not unfold when
the vehicle is unlocked. Pull again on control A
.
Unfolding
)
From outside: unlock the vehicle using the remote control or
the key.
)
From inside: with the ignition on, pull the control A
in the central
position rearwards.
The folding and unfolding of the door mirrors using the remote
control can be deactivated by a PEUGEOT dealer or a qualifi ed
workshop.
Never fold or unfold the electric folding mirrors manually.
Automatic tilting in reverse gear
System which provides a view of the ground during parking
manoeuvres in reverse gear.
Programming
)
With the engine running, engage reverse gear.
)
Select and adjust the left-hand and right-hand mirrors in
succession.
The adjustment is stored immediately.
Switching on
)
With the engine running, engage reverse gear.
)
Move control A
to the right or to the left to select the corresponding
mirror.
The glass of the mirror selected tilts downwards, in accordance with its
programming.
Switching off
)
Exit reverse gear and wait ten seconds.
or
)
Return control A
to the central position.
The mirror glass returns to its initial position.
The mirror glass also returns to its initial position:
- if the speed exceeds 6 mph (10 km/h),
- if the engine is switched off.
Page 81 of 336
3/
EASE OF USE and COMFORT
COURTESY LAMP
A.
Courtesy lamp
B.
Map reading lamps
COURTESY LAMP
In this position, the courtesy lamp comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when a door is opened,
- when the remote control locking button is activated, in order to
locate your vehicle. It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed.
Permanently off.
Permanent lighting.
With the "permanent lighting" mode, the duration of lighting varies,
depending on the circumstances:
- with the ignition off, approximately ten minutes,
- in energy economy mode, approximately thirty seconds,
- with the engine running, unlimited.
MAP READING LAMPS
)
With the ignition on, press the corresponding switch.
Page 82 of 336
80
INTERIOR MOOD LIGHTING
The dimmed passenger compartment lighting improves visibility in
the vehicle when the light is poor.
SWITCHING ON
At night, the footwell lighting and the front courtesy mood lamp come
on automatically when the sidelamps are switched on.
SWITCHING OFF
The interior mood lighting switches off automatically when the
sidelamps are switched off.
PROGRAMMING
The function is activated or deactivated via the vehicle
confi guration menu.
This function is activated by default.
INTERIOR WELCOME LIGHTING
The remote switching on of the passenger compartment lighting
makes your entry into the vehicle easier in poor light. It is activated in
accordance with the light intensity detected by the brightness sensor.
SWITCHING ON
)
Press the open padlock on the remote control.
The front door sill lighting, the footwell lighting and the courtesy lamps
come on; your vehicle is also unlocked.
SWITCHING OFF
The interior welcome lighting switches off automatically after a set time
or when one of the doors is opened.
The welcome lighting duration is associated with and identical to
that of the automatic guide-me-home lighting.
Page 83 of 336
3/
EASE OF USE and COMFORT
EXTERIOR WELCOME LIGHTING
The remote switching on of the lighting makes your approach to the
vehicle easier in poor light. It is activated according to the level of light
detected by the sunshine sensor.
SWITCHING ON
)
Press the open padlock on the remote control.
The dipped beam headlamps and the sidelamps come on; your
vehicle is also unlocked.
PROGRAMMING
The duration of the welcome lighting is associated with and
identical to that of the automatic guide-me-home lighting.
The lighting duration is selected via the vehicle
confi guration menu.
SWITCHING OFF
The exterior welcome lighting switches off automatically after a set
time, when the ignition is switched on or on locking the vehicle.
Page 173 of 336
8/
PRACTICAL INFORMATION
BATTERY
The battery is located under the bonnet.
For access to it:
)
open the bonnet using the interior release lever, then the exterior
safety catch,
)
remove the plastic cover for access to the two terminals,
)
wait 2 minutes after switching off the ignition before disconnecting
the battery,
)
unclip the fusebox to remove the battery, if necessary.
STARTING USING ANOTHER BATTERY
)
Connect the red cable to the positive terminal (+) of the fl at
battery A
, then to the positive terminal (+) of the slave battery B
.
)
Connect one end of the green or black cable to the negative
terminal (-) of the slave battery B
.
)
Connect the other end of the green or black cable to the earth
point C
on the broken down vehicle.
)
Operate the starter, let the engine run.
)
Wait until the engine returns to idle and disconnect the cables.
ACCESS TO THE BATTERY
The batteries contain harmful substances such as sulphuric
acid and lead. They must be disposed of in accordance with
regulations and must not, in any circumstances, be discarded with
household waste.
Take used remote control batteries and vehicle batteries to a
special collection point.
Page 174 of 336
172
DISCONNECTING / RECONNECTING THE
CABLES
To avoid discharging the battery, do not leave the vehicle lighting
on repeatedly with the ignition off (refer to the "Energy economy
mode" paragraph).
It is advisable to disconnect the battery if the vehicle is to be left
unused for more than one month.
Do not disconnect the terminals while the engine is running.
Do not charge the batteries without disconnecting the terminals
fi rst.
Before disconnecting the battery
Wait 2 minutes after switching off the ignition before disconnecting
the battery.
Retract the active spoiler then close the windows and the doors
before disconnecting the battery.
Following reconnection of the battery
Following reconnection of the battery, switch on the ignition
and wait 1 minute before starting to permit initialisation of the
electronic systems. However, if slight problems remain following
this operation, contact a PEUGEOT dealer or a qualifi ed
workshop.
Referring to the corresponding section, you must yourself
reinitialise:
- the remote control key,
- the electric windows and the automatic partial opening of the
door windows,
- the GPS satellite navigation system.
)
Raise the locking tab D
fully.
)
Position the open clip E
of the cable on the positive terminal (+) of
the battery.
)
Press vertically on the clip E
to position it correctly against the
battery.
)
Lock the clip by lowering the tab D
.
CHARGING THE BATTERY USING A BATTERY
CHARGER
)
Disconnect the battery from the vehicle.
)
Follow the instructions for use provided by the manufacturer of the charger.
)
Reconnect starting with the negative terminal (-).
)
Check that the terminals and connectors are clean. If they are
covered with sulphate (whitish or greenish deposit), remove them
and clean them.
Do not force the tab as locking will not be possible if the clip is not
positioned correctly.
Start the procedure again.