clock PONTIAC GRAND PRIX 2008 Owner's Manual

Taillamps, Turn Signal, and
Stoplamps
A. Taillamp
B. Taillamps, Turn Signal
and Stoplamps
1. Open the trunk. SeeTrunk on page 2-14for more
information.
2. Remove the convenience net, if equipped, by
removing the net hook attachments.
3. Remove the plastic cap from the trunk trim.
4. Pull the trunk trim and carpet away from the back of
the trunk.
5. Remove the bottom bolt and two nuts.6. Remove the taillamp
assembly by pulling it
out from the vehicle.
7. Turn the appropriate
lamp socket a quarter
turn counterclockwise
and remove it.
8. Remove the old bulb.
5-58

9. Replace with a new bulb into the socket and turn
the lamp socket clockwise to install it.
10. Reinstall the taillamp assembly by reversing
Steps 2 through 5.
Back-Up Lamps
The back-up lamps are located on the trunk lid.
To replace the back-up lamp bulb(s):
1. Open the trunk. SeeTrunk on page 2-14for more
information.2. Turn the appropriate lamp socket a quarter turn
counterclockwise and remove it.
3. Remove the old bulb.
4. Put the new bulb into the lamp socket.
5. Turn the bulb a quarter turn clockwise to reinstall it.
5-59

License Plate Lamp
To replace one of these bulbs:
1. Open the trunk. SeeTrunk on page 2-14
2. Turn the appropriate lamp socket a quarter turn
counterclockwise and remove it.
3. Remove the old bulb.
4. Put the new bulb into the lamp socket.
5. Turn the bulb a quarter turn clockwise to reinstall it.
Replacement Bulbs
Exterior Lamps Bulb Number
Back-Up Lamp 3157
Front Parking/Turn Signal Lamp3757 NAK* or
5702 KA**
Front Sidemarker and License
Plate Lamp194
Headlamps
High-Beam Halogen 9005
Low-Beam Halogen 9006
Stop/Taillamp/Turn Signal Lamps 3057
* Base Models with the Optional Fog Lamps
** For Lamps Not Equipped with the Fog Function and
GXP Models
For replacement bulbs not listed here, contact your
dealer/retailer.
5-60

Accessing the Tire Inator Kit
To access the tire inator kit:
1. Open the trunk. SeeTrunk on page 2-14for more
information.
2. Locate the tire inator kit by lifting up the carpet.
3. Remove the inator kit
cover by turning the
center nut
counterclockwise.
4. Remove the inator kit by pulling it straight out of
the foam container.
5-88

Tire Sealant
The kit contains a liquid sealant that when injected into
a at tire, may temporarily repair nail holes or cuts in the
tread area of the tire. The tire sealant cannot repair tire
damage caused while driving on a at tire or a tire that
has had a “blow out” or a tire that has punctures in the
sidewall areas. The tire sealant solution is to be used for
a single tire and can only be used once.
Check the tire sealant expiration date on the sealant
canister. The sealant may not be as effective beyond the
expiration date. If needed, see your dealer/retailer for
a replacement canister.
After temporarily repairing a tire using the tire sealant,
take your vehicle to your dealer/retailer to have the
tire inspected and repaired.
Using the Tire Inator Kit
To use the tire inator kit:
1. Place the inator kit on the ground and unwrap the
sealant lling hose from the compressor.
2. Remove the air compressor accessory plug from
the unit. To do this, pull the top portion of the
wrapped cord out rst, then the bottom, then unsnap
the plug. Do not insert the plug into an accessory
outlet yet.
3. Remove the valve stem cap from the at tire by
turning it counterclockwise.
If an object, such as a nail, has penetrated the tire,
do not remove it.
5-89

4. Attach the sealant lling hose (A) onto the tire valve
stem. Turn it clockwise until it is tight.
Make sure the inator kit on/off switch (B) is in the
O (off) position.
5. Plug the air compressor accessory plug (C) into an
accessory power outlet in the vehicle. See
Accessory Power Outlet(s) on page 3-26for more
information.
{CAUTION:
Idling the engine in a closed-in place or with
the climate control system off can cause
deadly carbon monoxide (CO). SeeEngine
Exhaust on page 2-36.
6. Start the vehicle. SeeStarting the Engine on
page 2-25for more information. The vehicle must be
running while using the air compressor.
{CAUTION:
Inating something too much can make it
explode, and you or others could be injured.
Be sure to read the inator instructions, and
inate the tire to its recommended pressure.
Do not exceed 36 psi (248 kPa).
7. Move the inator kit switch to the I (on) position.
The inator kit will force sealant and air into the
tire. Sealant may leak from the puncture hole until
the vehicle is driven and the hole has sealed.
5-90

8. Make sure there is a proper connection between
the tire valve stem and the sealant lling hose by
looking at the air pressure gage. If there is not a
pressure reading while the compressor is running,
the connection between the inator kit and the
tire is bad.
Check the attachment between the sealant lling
hose and the tire valve stem.
9. Inate the tire up to the recommended ination
pressure, found on the Tire and Loading Information
label located on the vehicle’s center pillar (B-pillar)
below the vehicle’s door latch, using the air pressure
gage on the top of the unit as a guide.
The pressure gage reading is slightly high while the
compressor is on. Turn the compressor off to get
an accurate pressure reading.
Notice:If the recommended pressure cannot be
reached after 15 minutes, the vehicle should not be
driven. The tire is too severely damaged and
cannot be inated or sealed with the tire sealant
and compressor kit. Remove the air compressor
accessory plug from the accessory power outlet and
unscrew the sealant/air hose from the tire valve or
tire pressure monitoring sensor valve. SeeRoadside
Assistance Program on page 7-6.10. Move the inator kit switch to the O (off) position
once the correct tire pressure is obtained.
11. Turn off the engine.
12. Unplug the air compressor accessory plug from the
accessory power outlet in the vehicle.
13. Disconnect the sealant lling hose from the tire
valve stem, by turning it counterclockwise, and
replace the tire valve stem cap.
Be careful when handling the tire inator
components as they may be hot after usage.
14. Wrap the sealant lling hose around the air
compressor channel to stow it in its original location.
5-91

15. Stow the air compressor accessory plug back in the
air compressor. To do this, wrap the air compressor
accessory plug, snap in the plug, and then push in
the bottom and then the top of the wrapped air
compressor accessory plug.
16. If the at tire was able
to inate to the
recommended ination
pressure, remove the
maximum speed label
from the sealant
canister.
Place it in a highly visible location such as the
inside of the upper left corner of the windshield or
to the face of the radio/clock.
The maximum speed label reminds you to drive
cautiously and not to exceed 55 mph (90 km/h) until
you have the damaged tire inspected and repaired.
{CAUTION:
Storing the tire sealant and compressor kit or
other equipment in the passenger
compartment of the vehicle could cause injury.
In a sudden stop or collision, loose equipment
could strike someone. Store the tire sealant
and compressor kit in the proper place.
17. Return the equipment to the proper storage location
in the trunk of your vehicle.
18. Immediately drive the vehicle 5 miles (8 km) to
distribute the sealant evenly in the tire. Stop at a
safe location and check the tire pressure. Refer to
Steps 1 through 8 under “Using the Air Compressor
without Sealant” next in this section. If the tire
pressure has fallen more than 10 psi (68 kPa) below
the recommended ination pressure, stop driving
the vehicle. The tire is too damaged for the sealant to
work. SeeRoadside Assistance Program on
page 7-6.
If the tire pressure has not dropped more than
10 psi (68 kPa) from the recommended ination
pressure, you can inate the tire back up to the
recommended ination pressure.
5-92

4. Turn the sealant canister so the inator lling hose
is aligned with the slot in the compressor.
5. Lift the sealant canister from the air compressor
and replace with a new sealant canister. See
your dealer/retailer for more information.To install a new sealant canister:
1. Align the sealant lling hose with the slot in the air
compressor.
2. Push the sealant canister down and turn it
clockwise.
3. Wrap the sealant lling hose around the air
compressor channel to stow it in its original location.
4. Push the air compressor inator hose onto the
sealant canister inlet and push the lever down.
Changing a Flat Tire
If a tire goes at, avoid further tire and wheel damage
by driving slowly to a level place. Turn on your vehicle’s
hazard warning ashers. SeeHazard Warning Flashers
on page 3-6for more information.
5-96

Removing the Spare Tire and Tools
The equipment needed to change a tire is located in
the trunk.
1. Open the trunk. SeeTrunk on page 2-14for more
information.
2. Remove the convenience net, if equipped, by
removing the net hook attachments.
3. Lift up the carpet.4. Turn the center nut on
the compact spare tire
cover counterclockwise
to remove it.
5. Remove the cover.
6. Remove the compact spare tire. SeeCompact
Spare Tire on page 5-109for more information.
5-98