warning light PORSCHE 911 TURBO 2014 6.G Owner's Guide

106 Instrument Panel and Multi-Function Display
fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
The display as well as the settings for the Tire Pressure Monitoring System take place on the multi-function display.
However, the tire pressure must still be set manually on the wheel.fPlease see the chapter “TIRE PRESSURE FOR COLD TIRES (68 °F/ 20 °C)” on page 287.
Driving the vehicle with low tire pressure increases the risk of a tire failure and resulting loss of control. Furthermore, low tire pressure increases rate of wear of the affected tires.Please note that the Tire Pressure Monitoring System is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of Tire Pressure Monitoring System low tire pressure telltale. Low tire pressure reduces the road safety of the vehicle and destroys the tire and wheel.
Tire Pressure Monitoring System gives a warning about a pressure drop caused by natural diffusion as well as about a gradual loss of pressure caused by foreign objects.Tire Pressure Monitoring cannot warn you about tire damage that occurs suddenly (e.g. flat tire due to abrupt external effects).fWhen a red tire pressure warning appears, stop immediately in a suitable place and check the tires for damage. If necessary, remedy the damage with a tire sealant.fDo not by any means continue to drive with defective tires.
fSealing the tire with tire sealant is only an emergency repair so you can drive to the nearest specialist workshop.The maximum permitted speed is 50 mph (80 km/h) .fDo not drive with tires in which the tire pressure drops again very quickly. In case of doubt, have tires checked by a specialist workshop.fDefective tires must be replaced immediately at an authorized Porsche dealer.Tires must never be repaired under any circumstances.fIf Tire Pressure Monitoring System is defective (e.g. defective wheel transmitter), contact an authorized Porsche dealer immediately and have the damage repaired. The tire pressure will not be monitored at all or will be monitored only partially when Tire Pressure Monitoring System is defective.
For information on warning messages on the multi- purpose display:fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.fIncomplete entries or selection of the wrong tires on the multi-purpose display affect the accuracy of warnings and messages.The settings in the tire pressure menu must be updated following a wheel change or changes in vehicle loading.fUse only the pressure differences shown in the “ Fill info” display in the Tire pressure menu or from the corresponding tire pressure warning when correcting the tire pressure.fTires can lose air over time without a tire defect being present. A tire pressure warning
will then appear on the multi-purpose display.Check the tire pressure at the next opportunity.
Warning light
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.The TPMS malfunction indicator is combined with the low tire pressure telltale.When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended.TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.fAlways check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.
Maintaining Tire Pressure
WARNINGh
Attention to TPMS Malfunction Indicator
WARNINGh
14_991_Turbo_21.book Seite 106 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 107
The warning light in the instrument panel lights up: – When a loss in pressure has been detected.– In the event of a defect in Tire Pressure Monitoring or a temporary fault.– When learning new fitted wheels/wheel transmitters, as long as the vehicle’s own wheels have not yet been recognized.
The tire pressure warning light on the instrument panel goes out only when the cause of the fault has been rectified.
Overview of tire pressure monitoring functions
Tire Pressure Monitoring offers the following functions: – Display of the actual tire pressure when stationary and while the vehicle is in motion.– Tire pressure warnings in two stages (yellow and red warning).– In the “TPMS” menu, the settings “Fill info” (display of the deviation from the required pressure, refill pressure), “Tire type”, “Full load” and “Comfort press.” are available when the vehicle is stationary.
Tire pressure display on the multi-function display
Selecting the TPMS function on the multi-function display
The “ TPMS” function displays the temperature- dependent tire pressures (actual pressures) in the four wheels.You can watch the tire pressure rise as the temperature increases while driving.
Information
This display of the actual pressures is only for information.fUnder no circumstances should the tire pressures be changed based on this display.
Information
After the ignition is switched on, it can take up to approx. 1 minute until all tire pressures are displayed. Dashes (-.-) appear instead of the tire pressures.
1. Select the “TPMS” main menu.
14_991_Turbo_21.book Seite 107 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 111
“Comfort pressure Reduce speed“ warning
If the maximum speed of the preset comfort pressure is exceeded and the tire pressure is below a critical limit, a warning message appears on the multi-function display.
Driving at excessive speeds when the comfort pressure is active will destroy the tires.fReduce speed to below the displayed maximum speed.fAlways inflate the tires to the standard tire pressure when driving at higher speeds.
System learning
Tire Pressure Monitoring System begins to “learn” the tires after a wheel change, wheel transmitter replacement or update of the tire settings. During this process, TPMS recognizes the wheels and their locations.The message “ No tire pressure monitoring System is learning ” appears on the multi- function display.
The wheel learning process takes place exclusively when the vehicle is being driven (vehicle speed above 16 mph (25 km/h)).
TPMS requires a certain amount of time to learn the wheels. During this time, the current tire pressures are not available on the multi-function display:– The tire pressure warning light stays on until all wheels have been learned.– Lines (-.-) appear on the display of the “ TPMS” function.– The required pressures for cold tires (68 °F/20 °C) are shown under “ Fill info” in the “ TPMS” main menu.
Position and pressure information is displayed as soon as TPMS has assigned the wheels recognized as belonging to the vehicle to the correct wheel positions.fCheck the tire pressure for all wheels under “ Fill info”.fCorrect the tire pressure to the required pressure if necessary (differential pressure value “0.0”).
Tire pressure warnings
The tire pressure warning light on the instrument panel and a corresponding message on the multi-function display warn about loss of pressure in two stages (yellow and red), depending on the amount of pressure loss.
Driving at excessive speeds when the comfort pressure is active
WARNINGh
14_991_Turbo_21.book Seite 111 Mittwoch, 9. April 2014 2:19 14

112 Instrument Panel and Multi-Function Display
Yellow warning – “Top off air”
The pressure in the tire is more than 4 to 7 psi/ 0.3 to 0.5 bar/30 to 50 kPa too low. The tire pressure warning specifies the affected tire and the target tire pressure. fFill up with air at the next opportunity.
This tire pressure warning appears: – for approx. 10 seconds when the vehicle is stationary and the ignition is switched off or – when the ignition is switched on again.
The warning can be acknowledged when the ignition is switched on.The tire pressure warning light in the instrument panel goes out only when the tire pressure has been corrected (differential pressure value “0.0”).
Red warning – “Check tires”
At speeds below 100 mph (160 km/h): – The pressure in the tire has dropped by 20 % below the required pressure or by more than 7 psi/0.5 bar/50 kPa . This significant pressure loss is a danger to road safety.
At speeds above 100 mph (160 km/h): – The pressure in the tire has dropped by more than 6 psi/0.4 bar/40 kPa . This significant pressure loss is a danger to road safety.fWhen the tire pressure warning appears, stop immediately at a suitable location. Check the indicated tire for signs of damage. If necessary, fill in tire sealant and set the correct tire pressure.
This tire pressure warning also appears when driving and can be acknowledged. The tire pressure warning light in the instrument panel goes out only when the tire pressure has been corrected (differential pressure value “0.0”).
“Tire pressure Reduce speed” warning
At speeds above 165 mph (270 km/h): – The pressure in the tire has dropped by more than 4 psi/0.3 bar/30 kPa . This pressure loss is a danger to road safety.fWhen the tire pressure warning appears, reduce speed to below 165 mph (270 km/h) until the warning disappears.When driving at very high speeds, increase the tire pressure to the required pressure (differential pressure value “0.0”).
For information on tire sealing compound:fPlease see the chapter “FILLING IN TIRE SEALANT” on page 265.
14_991_Turbo_21.book Seite 112 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 113
Warning light
The warning light in the instrument panel lights up: – When a loss in pressure has been detected (warning light: lights up continuously).– In the event of a defect in TPMS or a temporary fault (warning light: flashes for 60 seconds, then lights up continuously).– When learning new fitted wheels/wheel transmitters, as long as the vehicle’s own wheels have not yet been recognized (warning light: flashes for 60 seconds, then lights up continuously).
A warning message also appears on the multi- function display in the instrument panel.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
The tire pressure warning light on the instrument panel goes out only when the cause of the fault has been rectified.
Changing a wheel and replacing tires
fNew wheels must be fitted with radio transmitters for Tire Pressure Monitoring System. Before tires are changed, the battery charge condition of the wheel transmitters should be checked.fPlease contact an authorized Porsche dealer.fSwitch off the ignition when changing a wheel.
The tire settings on the multi-function display must be updated after changing a wheel.If the tire settings are not updated, the message “Tire change? Update settings” is displayed on the multi-function display.fUpdate the multi-function display settings the next time the vehicle is stationary.
Pressure increase as the result of temperature increase
In accordance with physical principles, the tire pressure changes as the temperature changes.For every 18 °F (10 °C) change in temperature, the tire pressure increases or decreases by around 1.5 psi/0.1 bar/10 kPa.
Partial monitoring
Monitoring of the other wheels is continued if there is a fault in one or two wheel transmitters.– The tire pressure warning light lights up.– The message “Restricted monitoring” appears on the multi-function display.– No tire pressures are displayed on the multi-function display for wheels with faulty wheel transmitters.
No monitoring
In the event of faults, Tire Pressure Monitoring System cannot monitor the tire pressure. The warning light on the instrument panel lights up and a corresponding message appears on the multi-function display.
Monitoring is not active: – In the event of a defect in TPMS or if more than 2 wheel transmitters are defective.– If wheel transmitters for Tire Pressure Monitoring System are missing.– During the learning phase after the tire settings have been updated.– After a wheel change without updating the tire settings.– If more than four wheel transmitters are recognized.– If there is external interference by other radio sources, e.g. wireless headphones.– If tire temperatures are too high.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
14_991_Turbo_21.book Seite 113 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 129
Overview of Warning and Information Messages
If a warning message appears, always refer to the corresponding sections in this Owner’s Manual. Warning messages are issued only if all measurement prerequisites are met. Therefore, check all fluid levels regularly – in particular, always check the engine oil level before refueling.
Warning and information message categories
fVisit or consult an authorized Porsche dealer immediately.
fVisit an authorized Porsche dealer at the next opportunity.
fVisit an authorized Porsche dealer at the next opportunity or remedy yourself.
Red System failure or warning
Yellowfault or system failure warning
WhiteInformation/message
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
Oil press. too low Park vehiclesafely
Stop immediately in a suitable place and switch engine off. Do not continue driving. Select “Oil measurement” on the multi-function display. Add engine oil if necessary.Do not continue driving if the warning message is displayed despite the oil level being correct.Have the fault corrected at an authorized Porsche dealer.
Oil pressure measurement faultDriving permittedConsult a workshop
Have the fault corrected at an authorized Porsche dealer.
Oil temperature too high Reduce load Switch engine off and let it cool. Check oil level and, if necessary, add oil.
Oil temperature indicator faultConsult a workshopDriving permitted
Have the fault corrected at an authorized Porsche dealer.
Oil level measurement faultConsult a workshopDriving permitted
Have the fault corrected at an authorized Porsche dealer.
No information about oil levelavailable at present
The oil level can be checked after waiting for approx. 1 minute with the vehicle parked on a level surface and the engine at operating temperature. If the rear luggage compartment lid is opened when the engine is cold (e.g. to top up engine oil), the oil level cannot be displayed for a certain time.
14_991_Turbo_21.book Seite 129 Mittwoch, 9. April 2014 2:19 14

130 Instrument Panel and Multi-Function Display
Oil level minimum reachedRefill oil
Top up engine oil immediately.
Oil level below min. Refill oil at once Do not drive on
Top up engine oil immediately.
Oil level above maximumConsult a workshopDriving permitted
Visit an authorized Porsche dealer at the next opportunity and have the oil drained to the correct level.
Gauge moves to maximum markEngine too hot Park vehicle to cool down Coolant or engine oil temperature is too high. Switch off engine and let it cool.Check coolant or engine oil level. If necessary, top up coolant / engine oil.
Refill coolant Observeengine temperature
Check coolant level. Add coolant if necessary.
Gauge moves to maximum markRefill coolant immediatelyDo not drive on
Switch engine off and let it cool. Check coolant level. Add coolant if necessary.
Cooling system faultConsult a workshopService required
Have the fault corrected at an authorized Porsche dealer.
Coolant temp indicator faultDriving permittedConsult a workshop
Have the fault corrected at an authorized Porsche dealer.
Engine fan failure Avoid full loadDriving permitted
Have the fault corrected at an authorized Porsche dealer.
Generator fault Park vehiclesafely
Stop in a suitable place and switch engine off. Do not continue driving.Have the fault corrected at an authorized Porsche dealer.
Low battery Start the engine and run for extended period
Start the engine immediately so that the battery can be charged.
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
14_991_Turbo_21.book Seite 130 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 131
Low battery Consumption off The power supply to various comfort features is deactivated to prevent the battery from discharging.
Battery protection was active during parking The power supply to various features was deactivated during parking to prevent the battery from discharging.
Battery function restrictedConsult a workshop
Consult an authorized Porsche dealer.
Reduced power Driving permittedConsult a workshop
Consult an authorized Porsche dealer.
Engine control fault Consult a workshopDriving permitted
Have the fault corrected at an authorized Porsche dealer.
Please start engine manually Start engine manually at the ignition.
Please switch offthe ignition
To prevent the battery from discharging, switch off the ignition when leaving the vehicle after the engine was stopped automatically.
Display of selector-lever position flashes
Engage gear selector properly PDK transmission: Selector lever may be positioned between two settings. Engage selector lever properly.
Move gear lever to position P PDK transmission: Move gear lever to position P before removing key from ignition lock or stopping and securing the vehicle.
Move gear lever to P or N PDK transmission: Engine can only be started in selector-lever position P or N.
Activate brake PDK transmission: Apply the footbrake when starting.
Display of selector-lever position flashes
Transm. fault Poss. no R gearPossible to drive on
Restricted gearshift comfort, reverse gear not available. Have the fault corrected at an authorized Porsche dealer.
Display of selector-lever position flashes
Transm. failure Park vehiclesafely
No selector-lever position is displayed on the instrument panel. Vehicle can be driven only until it comes to a stop.It is not possible to continue driving. Stop the vehicle immediately in a suitable place. Read the instructions in the section “Towing”. Have the fault corrected at an authorized Porsche dealer.
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
14_991_Turbo_21.book Seite 131 Mittwoch, 9. April 2014 2:19 14

132 Instrument Panel and Multi-Function Display
Drive temperature too highReduce load
“Warning jerks” can be felt when driving off and the engine power may be restricted. Do not use the accelerator to hold the vehicle, e.g. on a hill. Hold the vehicle with the brake.Reduce engine load. Stop the vehicle in a suitable place if possible.Allow the engine to run in selector-lever position P or N until the warning disappears.
Transmission overheated Park vehicle to cooling
Transmission temperature too high. Stop the vehicle at a suitable place, switch off engine and allow it to cool down.Have the fault corrected at an authorized Porsche dealer.
Press clutch Manual transmission: Depress clutch pedal when starting.
Brake fluid level Park vehiclesafely
Stop immediately in a suitable place. Do not continue driving. Have the fault corrected at an authorized Porsche dealer.
Brake distribution fault Park vehicle safely Stop immediately in a suitable place. Do not continue driving. Have the fault corrected at an authorized Porsche dealer.
Brake cooling faulty Brake temperature too high. Stop the vehicle at a suitable place, switch off engine and allow the brake to cool down.Have the fault corrected at an authorized Porsche dealer.
ABS/PSM failure Adapted driving permitted Have the fault corrected at an authorized Porsche dealer.
Wear limit Change brake padsDriving permitted
Have brake pads replaced immediately. Consult an authorized Porsche dealer.
flashes
Release parking brake Pull the electric parking brake switch.
Press brake pedal Press the brake pedal before releasing the electric parking brake.
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
14_991_Turbo_21.book Seite 132 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 133
Fault parking brake Have the fault corrected at an authorized Porsche dealer.
Electric parking brake inservice mode
Have the fault corrected at an authorized Porsche dealer.
flashes
Emergency braking Emergency braking function of the electric parking brake active.
PSM system error Park vehicle safely
Stop the vehicle in a suitable place. Do not continue driving.Have the fault corrected immediately at an authorized Porsche dealer.
PSM failureConsult a workshopAdapted driving permitted
Have the fault corrected at an authorized Porsche dealer.
PSM off Porsche Stability Management was switched off.
PSM onPorsche Stability Management was switched on.
flashes
PSM in diagnosis Porsche Stability Management is in diagnostic test mode.
Spoiler loss Reducespeed
Driving stability is impaired. Reduce speed and adjust driving style. Have the fault corrected at an authorized Porsche dealer.
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
14_991_Turbo_21.book Seite 133 Mittwoch, 9. April 2014 2:19 14