fuel pressure Ram 2500 2017 Diesel Supplement

Do Not Operate The Engine With Low Oil Pressure
When the engine is at normal operating temperature, the
minimum oil pressures required are:
Idle 700 to 800 RPM 10 psi (69 kPa)
Full speed and load 30 psi (207 kPa)
CAUTION!
If oil pressure falls to less than normal readings, shut
the engine off immediately. Failure to do so could
result in immediate and severe engine damage.
Do Not Operate The Engine With Failed Parts
All engine failures give some warning before the parts fail.
Be on the alert for changes in performance, sounds, and
visual evidence that the engine requires service. Some
important clues are:
•Engine misfiring or vibrating severely.
• Sudden loss of power.
• Unusual engine noises. •
Fuel, oil or coolant leaks.
• Sudden change, outside the normal operating range, in
the engine operating temperature.
• Excessive smoke.
• Oil pressure drop.
ENGINE BLOCK HEATER — IF EQUIPPED
The engine block heater warms engine coolant and permits
quicker starts in cold weather. Connect the heater cord to a
ground-fault interrupter protected 110–115 Volt AC electri-
cal outlet with a grounded, three-wire extension cord.
The engine block heater cord is routed under the hood to
the right side and can be located just behind the grille near
the headlamp.
NOTE: The engine block heater cord is a factory installed
option. If your vehicle is not equipped, heater cords are
available from your authorized MOPAR dealer.
The block heater must be plugged in at least one hour to
have an adequate warming effect on the coolant.5
STARTING AND OPERATING 137

If the vehicle will not start, refer to “Maintenance
Procedures/Priming If The Engine Has Run Out Of Fuel”
in “Maintaining Your Vehicle” for further information.
WARNING!
Do not open the high pressure fuel system with the
engine running. Engine operation causes high fuel
pressure. High pressure fuel spray can cause serious
injury or death.
Diesel Exhaust Fluid Storage
Diesel Exhaust Fluid (DEF) is considered a very stable
product with a long shelf life. If DEF is kept in tempera-
tures between 10° and 90°F (-12° and 32°C), it will last a
minimum of one year.
DEF is subject to freezing at the lowest temperatures.
For example, DEF may freeze at temperatures at or below
12° F (-11° C). The system has been designed to operate in
this environment.
NOTE:When working with DEF, it is important to know
that:
• Any containers or parts that come into contact with DEF
must be DEF compatible (plastic or stainless steel). Copper, brass, aluminum, iron or non-stainless steel
should be avoided as they are subject to corrosion by
DEF.
• If DEF is spilled, it should be wiped up completely.
Adding Diesel Exhaust Fluid
The DEF gauge (located on the instrument cluster) will
display the level of DEF remaining in the tank. Refer to
“Instrument Cluster” and “Instrument Cluster Descrip-
tions” in “Understanding Your Instrument Panel” for fur-
ther information.
NOTE:
•Driving conditions (altitude, vehicle speed, load, etc.)
will effect the amount of DEF that is used in your
vehicle.
• Another factor is that outside temperature can affect
DEF consumption. In cold conditions, 12° F (-11° C) and
below, the DEF gauge needle can stay on a fixed position
and may not move for extended periods of time. This is
a normal function of the system.
164 STARTING AND OPERATING

NOTE:WIF sensor is re-usable. Service kit comes with new
o-ring for filter canister and WIF sensor.
Priming If The Engine Has Run Out Of Fuel
WARNING!
Do not open the high pressure fuel system with the
engine running. Engine operation causes high fuel
pressure. High pressure fuel spray can cause serious
injury or death.
1. Add a substantial amount of fuel to the tank, approxi- mately 2 to 5 gal (8L to 19L).
2. Turn ignition switch to the start position to engage starter for one second, return ignition switch to run
position. This will activate in tank fuel pump for ap-
proximately 15 seconds. Repeat this process twice.
3. Start the engine using the “Normal Starting” procedure. Refer to “Starting Procedures” in “Starting and Operat-
ing” for further information.
CAUTION!
Do not engage the starter motor for more than 15
seconds at a time. Allow two minutes between the
cranking intervals.
NOTE: The engine may run rough until the air is forced
from all the fuel lines.
WARNING!
Do not use alcohol or gasoline as a fuel blending agent.
They can be unstable under certain conditions and be
hazardous or explosive when mixed with diesel fuel.
CAUTION!
Due to lack of lubricants in alcohol or gasoline, the use
of these fuels can cause damage to the fuel system.
NOTE:
• A maximum blend of 5% biodiesel, meeting ASTM
specification D-975 may be used with your Cummins
diesel engine. (Chassis Cab models not configured with
B20 capability.)
188 MAINTAINING YOUR VEHICLE

•A maximum blend of 20% biodiesel, meeting ASTM
specification D-7467 may be used with your Cummins
diesel engine. (Pickup models and Chassis Cab models
configured with B20 capability.)
• Use of biodiesel mixture in excess of 20% can negatively
impact the fuel filter’s ability to separate water from the
fuel, resulting in high pressure fuel system corrosion or
damage.
• Ethanol blends are not recommended or approved for
use with your Cummins diesel engine.
• In addition, commercially available fuel additives are
not necessary for the proper operation of your Cummins
diesel engine.
Intervention Regeneration Strategy — Message
Process Flow
The Cummins diesel engine meets all EPA Heavy Duty
Diesel Engine Emissions Standards, resulting in one of the
lowest emitting diesel engines ever produced.
To achieve these emissions standards, your vehicle is
equipped with a state-of-the-art engine and exhaust sys-
tem. The engine and exhaust after-treatment system work
together to achieve the EPA Heavy Duty Diesel Engine Emissions Standards. These systems are seamlessly inte-
grated into your vehicle and managed by the Cummins
Powertrain Control Module (PCM). The PCM manages
engine combustion to allow the exhaust system’s catalyst
to trap and burn Particulate Matter (PM) pollutants, with
no input or interaction on your part.
If the engine is allowed to idle or the truck is driven on low
engine speed drive cycles for more than 2 hours, the
system will automatically enter an emissions operating
mode that will increase the engine idle speed to 900 RPM
(1050 RPM for Chassis Cab). While in this mode, which is
designed to help maintain the diesel particulate filter, the
engine idle speed will return to normal when the brake
pedal is applied. A small change in engine tone or a slight
change in engine performance while accelerating may also
be noticeable at speeds below 20 mph (32 kmh). This
operating mode may last for up to an hour of idle time, or
around 20 minutes of driving time.
Additionally, your vehicle has the ability to alert you to
additional maintenance required on your truck or engine.
Refer to “Instrument Cluster Display” in “Understanding
Your Instrument Panel” for further information.
7
MAINTAINING YOUR VEHICLE 189

MS.90032) and distilled water for proper corrosion pro-
tection of your engine which contains aluminum com-
ponents.
• Make sure that the coolant expansion bottle overflow
hoses are not kinked or obstructed.
• Keep the front of the radiator clean. If your vehicle is
equipped with air conditioning, keep the front of the
condenser clean.
• Do not change the thermostat for Summer or Winter
operation. If replacement is ever necessary, install ONLY
the correct type thermostat. Other designs may result in
unsatisfactory engine coolant (antifreeze) performance,
poor gas mileage, and increased emissions.
Charge Air Cooler — Inter-Cooler
The charge air cooler is positioned below the radiator and
the air conditioner condenser. Air enters the engine
through the air cleaner and passes through the turbo-
charger, where it is pressurized. This pressurized air rap-
idly reaches high temperature. The air is then directed
through a hose to the charge air cooler and through another
hose to the intake manifold of the engine. The air entering the engine has been cooled by about 50° to 100°F (10° to
38°C). This cooling process enables more efficient burning
of fuel resulting in fewer emissions.
To guarantee optimum performance of the system, keep
the surfaces of the charge air cooler, condenser and radiator
clean and free of debris. Periodically check the hoses
leading to and from the charge air cooler for cracks or loose
clamps resulting in loss of pressure and reduced engine
performance.
Brake System
Brake Master Cylinder — Brake Fluid Level Check
The fluid level of the master cylinder should be checked
when performing under the hood service, or immediately
if the “Brake System Warning Light” indicates system
failure.
The brake master cylinder has a translucent plastic reser-
voir. On the outboard side of the reservoir, there is a
“MAX” mark and a “MIN” mark. The fluid level must be
kept within these two marks. Do not add fluid above the
full mark because leakage may occur at the cap.7
MAINTAINING YOUR VEHICLE 195

Adding Engine Coolant (Antifreeze)..............66
Adding Fuel ...............................45
Air Cleaner, Engine (Engine Air Cleaner Filter) ......57
Antifreeze (Engine Coolant) ....................65
Capacities ..............................71
Disposal ................................68
Automatic Transmission Fluid Type ..............................75
Axle Fluid ................................75
Battery ...................................64
Brake Fluid................................75
Brake System ..............................69
Fluid Check .............................69
Master Cylinder ..........................69
Capacities, Antifreeze (Engine Coolant) ............71
Capacities, Fluid ............................71
Caps, Filler Oil (Engine) .............................56
Radiator (Coolant Pressure) ..................67
Charge Air Cooler ...........................69
Coolant Pressure Cap (Radiator Cap) .............67
Cooling System .............................65
Adding Coolant (Antifreeze) .................66 Coolant Capacity
.........................71
Coolant Level ............................65
Disposal Of Used Coolant ...................68
Drain, Flush, And Refill .....................65
Points To Remember .......................68
Pressure Cap ............................67
Radiator Cap ............................67
Selection Of Coolant (Antifreeze) ...........65,72
Diesel Fuel ................................40
Diesel Fuel Requirements ......................40
Bulk Storage Of ..........................48
Diesel Fuel System, Re-Priming .................62
Disposal Antifreeze (Engine Coolant) ..................68
Draining Fuel/Water Separator Filter .............60
Engine ...................................54
Air Cleaner .............................57
Block Heater ..........................34,40
Break-In Recommendations ..................11
Compartment ............................54
Coolant (Antifreeze) .......................72
Identification ............................54
Idling .................................38
218 INDEX - RAM 1500

Oil.................................55,72
Oil Filler Cap............................56
Filters Air Cleaner .............................57
Engine Fuel .............................60
Engine Oil ...........................57,72
Engine Oil Disposal .......................57
Fluid Capacities ............................71
Fluid Level Checks Brake ..................................69
Fluid, Brake...............................75
Fluids, Lubricants And Genuine Parts .............72
Fuel .....................................40
Adding ................................45
Diesel ..............................40,72
Filter ..................................60
Requirements ............................40
Specifications ............................41
Tank Capacity ............................71
Fueling ..................................45
Gauges Voltmeter ...............................35
Instrument Cluster ..........................14 Intervention Regeneration Strategy
...............25
Keyless Enter-N-Go ..........................33
Maintenance Procedures ......................55
Maintenance Schedule ........................78
New Vehicle Break-In Period ...................11
Oil, Engine ................................55
Capacity ...............................71
Change Interval ..........................56
Dipstick ................................55
Disposal ................................57
Filter ...............................57,72
Filter Disposal ...........................57
Materials Added To ........................57
Recommendation .........................55
Viscosity ...............................56
Radiator Cap (Coolant Pressure Cap) .............65
Remote Starting System .......................10
Schedule, Maintenance .......................78
Selection Of Coolant (Antifreeze) ................72
8
INDEX - RAM 1500 219

Adding Engine Coolant (Antifreeze).............192
Adding Fuel ............................. .160
Air Cleaner, Engine (Engine Air Cleaner Filter) ......180
Air Filter ............................... .180
Antifreeze (Engine Coolant) ...................192
Capacities ............................. .204
Disposal .............................. .194
Automatic Transmission Adding Fluid .......................... .199
Fluid Level Check ....................... .198
Fluid Type ............................ .207
Shifting .............................. .141
Axle Fluid .............................. .207
Battery ................................. .190
Blanket ........................... .132 , 191
Emergency Starting ...................... .170
Brake System ............................ .195
Fluid Check ........................... .195
Master Cylinder ........................ .195
Brake/Transmission Interlock ..................141
Capacities, Antifreeze (Engine Coolant) ...........204
Capacities, Fluid .......................... .204Caps, Filler
Oil (Engine) ........................... .178
Radiator (Coolant Pressure) .................193
Charge Air Cooler ......................... .195
Coolant Pressure Cap (Radiator Cap) .............193
Cooling System ........................... .191
Adding Coolant (Antifreeze) .................192
Coolant Capacity ........................ .204
Coolant Level .......................... .191
Disposal Of Used Coolant ..................194
Drain, Flush, And Refill ....................192
Points To Remember ..................... .194
Pressure Cap ........................... .193
Radiator Cap .......................... .193
Selection
Of Coolant (Antifreeze) ..........192 , 205
Diesel Exhaust Brake ....................... .138
Diesel Fuel .............................. .157
Diesel Fuel Requirements .....................157
Bulk Storage Of ......................... .163
Diesel Fuel System, Re-Priming .................188
Disposal Antifreeze (Engine Coolant) .................194
Draining Fuel/Water Separator Filter .............184
8
INDEX - RAM 2500 / 3500 / 4500 / 5500 221