immobilizer RENAULT PULSE 2012 1.G Owners Manual


> (GLW    0RGHO .$2(0 B5HQDXOW @
JVP0086XType B1 Anti-Theft Sy\ftem key
2 Anti-Theft Sy\ftem key \bMolded)
3 Key number plate
JVP0087XType C1 Anti-Theft Sy\ftem key
2 Anti-Theft Sy\ftem key \bMolded)
3 Key number plate
JVC0063XType D1 Anti-Theft Sy\ftem key
2 Key number plate
Your vehicle can only be driven with the Anti-Theft
Sy\ftem key\f, which are regi\ftered to your vehicle’\f
Anti-Theft Sy\ftem component\f. A\f many a\f 5 Anti-
Theft Sy\ftem key\f can be regi\ftered and u\fed with
one vehicle. The new key\f mu\ft be regi\ftered by a
RENAULT dealer prior to u\fe with the Anti-Theft
Sy\ftem of your vehicle. Since the regi\ftration proce\f\f
require\f era\fing all memory in the Anti-Theft Sy\ftem
component\f when regi\ftering new key\f, be \fure to
take all Anti-Theft Sy\ftem key\f that you have to the
RENAULT dealer.
CAUTION:
Do not allow the Anti-Theft System key, which
contains an electrical transponder, to come into
contact with water or salt water. This could
affect the system function.
*: Immobilizer
INTELLIGENT KEY \bif equipped)
SPA2406Type A (with panic alarm)
SPA2502Type B (without panic alarm)1. Intelligent Key \b2)
2. Mechanical key \bin\fide the Intelligent Key) \b2)
3. Key number plate
Your vehicle can only be driven with the Intelligent
Key\f, which are regi\ftered to your vehicle’\f Intelligent
Key \fy\ftem component\f and Anti-Theft Sy\ftem*
component\f. A\f many a\f 4 Intelligent Key\f can be
regi\ftered and u\fed with one vehicle. The new key\f
mu\ft be regi\ftered by a RENAULT dealer prior to u\fe
with the Intelligent Key \fy\ftem and Anti-Theft Sy\ftem
of your vehicle. Since the regi\ftration proce\f\f require\f
Pre-driving checks and adjustments3-3
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
3-16Pre-driving checks and adjustments
Using panic alarm (if eq\fipped)
If \bo\f are near \bo\fr vehicle and feel threatened, \bo\f
ma\b activate the alarm to call attention as follows:
1. P\fsh the “PANIC”
b\ftton*3on the
Intelligent Ke\b for more than 0.5 second.
2. The theft warning alarm will sta\b on for 25 seconds.
3. The panic alarm stops when:
. It has r\fn for 25 seconds, or
. An\b of the b\fttons on the Intelligent Ke\b are
p\fshed. (Note: Panic b\ftton sho\fld be p\fshed for
more than 0.5 second.)
Hazard indicator operation
When \bo\f lock or \fnlock the doors, the hazard
indicator will flash as a confirmation.
.“LOCK”: The hazard indicator flashes once.
. “UNLOCK”: The hazard indicator flashes twice. Yo\fr vehicle is eq\fipped with either or both of the
following sec\frit\b s\bstems:
.
Theft warning s\bstem
. Anti-Theft S\bstem*
(* immobilizer)
The sec\frit\b condition will be shown b\b the sec\frit\b
indicator light.
THEFT WARNING SYSTEM
The theft warning s\bstem provides vis\fal and a\fdio
alarm signals if parts of the vehicle are dist\frbed.
Sec\frit\b indicator light
SIC2045
The sec\frit\b indicator light is located in the meter
panel.
This light operates whenever the ignition switch is in
the “ACC”, “OFF” or “LOCK” position. This is normal.
How to activate the system:
1. Close all windows and p\fsh the ignition switch to the “OFF” position.
The system can be activated even if the
windows are open. 2. Carr\b the Intelligent Ke\b with \bo\f and get o\ft of
the vehicle.
3. Make s\fre the hood is closed. Close and lock all doors with the door handle req\fest switch, LOCK
b\ftton*1on the Intelligent Ke\b (If the door
is locked \fsing the inside lock knob, the s\bstem
will not be activated) or power door lock switch (If
the door is locked \fsing the power door lock
switch with all the doors closed, the s\bstem will
not be activated. To activate the s\bstem, lock the
door \fsing the power door lock switch with an\b of
the doors open, then close all the doors) .
4. Confirm that the sec\frit\b indicator light comes on. The sec\frit\b indicator light sta\bs on for approxi-
matel\b 30 seconds. The vehicle sec\frit\b s\bstem is
now pre-armed. After approximatel\b 30 seconds
the vehicle sec\frit\b s\bstem a\ftomaticall\b shifts
into the armed phase. The sec\frit\b light begins to
flash once ever\b approximatel\b 3 seconds.
If, d\fring this 30-second pre-arm time period, the
door is \fnlocked with the door handle req\fest
switch, the “UNLOCK”
b\ftton*2on the
Intelligent Ke\b, the power door lock switch, or the
ignition switch is p\fshed to the “ACC” or “ON”
position, the s\bstem will not arm.
Even when the driver and/or passengers are in
the vehicle, the system will activate with all
doors locked and ignition switch in the “LOCK”
position. Push the ignition switch to the “ACC” or
“ON” position to turn the system off.
Theft warning system operation:
The warning s\bstem will give the following alarm:
. The hazard indicator blinks and the horn so\fnds
intermittentl\b for approximatel\b 30 seconds.
SECURITY SYSTEM (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
16. Radio memory buttons
17. RP\f (Repeat)\bMIX (Mix play) button
Anti-theft system (if equipped)
\fhis unit can only be activated when the ignition switch
for Anti-\fheft System is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
\fhe audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
\fo turn on the audio system, push the POWER ON\b
OFF button.
.\fhe system will turn on in the mode, (radio or CD)
which was used immediately before the system
was turned off.
. If there is no CD loaded, the radio will be turned
on.
\fo turn off the audio system, push the POWER ON\b
OFF button.
Volume control:
\fo control the volume, turn the VOLUME control dial.
\furn the VOLUME control dial clockwise to make the
sound louder.
\furn the VOLUME control dial counterclockwise to
make the sound quieter.
Sound preference button:
\fo enter the audio mode (radio or CD) , push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode. \fo change the audio settings (BASS, \fREBLE,
FADER, BALANCE, EQ) , push the
button or
EN\fER button to select the mode.
BASS ?\fREBLE ?BALANCE ?FADER ?EQ ?
BASS
\fo adjust each audio setting, turn the VOL control dial
clockwise or counterclockwise.
BASS: (í) to decrease \b (+) to increase
\fREB(LE): (í) to decrease \b (+) to increase
BAL(ANCE): (R) to right balance \b (L) to left balance
FADE(R): (F) to front fade \b (R) to rear fade
EQ (Equalizer): Use this control to change the preset
sound mode for CD play.
\furn the MENU\bVOL dial clockwise or counterclock-
wise. \fhe mode will change as follows:
OFF ⇔ENHANCE
If the audio settings mode is unchanged for approxi-
mately 8 seconds, the audio settings mode will
automatically return to the normal mode.
MENU button:
\fo configure the SPEED volume and BEEP settings,
perform the following procedure:
1. Push the MENU button.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
PHONE SE\fUP ⇔SPEED VOL⇔CLOCK ⇔
BEEP ⇔PHONE SE\fUP
. When SPEED VOL appears on the display, briefly
push on the EN\fER button then turn the VOLUME
dial clockwise or counterclockwise to adjust the
level of the volume. Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increasing the speed
volume setting results in the audio volume
increasing more rapidly with vehicle speed. Push
the EN\fER button again to save the setting.
. When BEEP appears on the display, briefly push
the EN\fER button and then turn the VOLUME dial
clockwise or counterclockwise to switch the beep
sound on or off. Push the EN\fER button again to
save the setting.
\fo configure Alternative Frequency, Regional and
Language settings, perform the following procedure:
1. Push and hold the MENU button for at least 1.5 seconds.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
AF⇔REG ⇔LANGUAGE ⇔AF
. \fo activate or deactivate the AF and REG mode,
briefly push on the EN\fER button when AF or
REG appears on the display and turn the
VOLUME dial clockwise or counterclockwise to
switch between the off or on position. After
selection, push the EN\fER button to confirm the
settings.
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak.
— When the REG mode is enabled, the audio unit will maintain and hold the station which is
broadcasting local (regional) programmes.
. \fo change the display language, briefly push the
EN\fER button when LANGUAGE appears on the
display then turn the VOLUME dial clockwise or
counterclockwise to select the appropriate lan-
guage setting.
Heater and air conditioner, and audio system4-25
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
17. AUX IN (auxiliary input\f jack
1\b. RPT (Repeat\f/MIX (Mix play\f button
19. TUNE/SEARCH button
Anti-theft system (if equipped\f
This unit can only be activated when the ignition switch
for Anti-Theft System is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
To turn on the audio system, push the POWER ON/
OFF button.
.The system will turn on in the mode, (radio or CD\f
which was used immediately before the system
was last turned off.
. If there is no CD loaded, the radio will be turned
on.
To turn off the audio system, push the POWER ON/
OFF button.
Volume control:
To control the volume, turn the VOLUME control dial.
Turn the VOLUME control dial clockwise to increase
the audio volume.
Turn the VOLUME control dial counterclockwise to
decrease the audio volume.
Sound preference button:
To enter the audio mode (radio or CD\f , push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode.
To change the audio settings (BASS, TREBLE,
FADER, BALANCE, EQ\f , push the
button or
ENTER button to select the mode.
BASS ?TREBLE ?BALANCE ?FADER ?EQ ?
BASS
To adjust each audio setting, turn the MENU/VOL
control dial clockwise or counterclockwise.
BASS: (í\f to decrease / (+\f to increase
TREB(LE\f: (í\f to decrease / (+\f to increase
BAL(ANCE\f: (R\f to adjust to the right / (L\f to adjust to
the left
FADE(R\f: (F\f to adjust to the front / (R\f to adjust to the
rear
EQ (Equalizer\f: Use this control to change the preset
sound mode for CD play.
Turn the MENU/VOL dial clockwise or counterclock-
wise. The mode will change as follows:
OFF ⇔ENHANCE ⇔OFF
If the audio settings mode is unchanged for approxi-
mately \b seconds, the audio settings mode will
automatically return to the normal mode.
Clock display:
Turning on/off the clock display
To turn on or off the clock display, perform the
following operations.
1. Push the MENU button while the audio system is on. ("PHONE SETUP" is displayed.\f 2. Turn the VOLUME control knob until "CLOCK"
appears on the display.
3. Push the ENTER button. ("CLOCK OFF" or "CLOCK ON" is displayed.\f
4. To turn on the clock display, turn the VOLUME control knob till "CLOCK ON" is displayed. To turn
off the clock display, turn the VOLUME control
knob till "CLOCK OFF" is displayed, and push
ENTER.
Clock adjustment
To adjust the time of the clock, perform the following
operations.
1. Push the ENTER button while "CLOCK ON" is displayed.
2. The hour display will flash.
3. Turn the VOLUME control knob to adjust the hour.
4. Push the ENTER button. The minute display will flash.
5. Turn the VOLUME control knob to adjust the minute.
6. Push the ENTER button to complete the clock adjustment.
AUX button:
The AUX IN jack is located on the audio unit. The AUX
IN audio input jack accepts any standard analog audio
input such as from a portable cassette tape player, CD
player, MP3 player or laptop computer.
Push the AUX button to play a compatible device when
it is plugged into the AUX IN jack.
RENAULT strongly recommends using a stereo mini
plug cable when connecting your music device to the
audio system. Music may not play properly when a
Heater and air conditioner, and audio system4-41
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
FOR EUROPE
Remote keyless entry system (if e\fuipped\b
Hereby, ALPS ELECTRIC CO.,LTD. declares that
these Keyless and TPMS TUNER; model TWC1G124
and Keyless Transmitter; model TWB1U761 are in
compliance with the essential re\fuirements and other
relevant provisions of Directive 1999/5/EC.
CAUTION:
Do not exposed to excessive heat such as
sunshine, fire or the like.
CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equiva-
lent type.
Intelligent Key system (if e\fuipped\b
Hereby, ALPS ELECTRIC CO.,LTD. declares that
these Passive Entry System(Hand Unit\b;model
TWB1G662, Passive Entry System(Tuner\b;model
TWC1G135, ANT ASSY-IMMOBILISER;model
TWK1A002 are in compliance with the essential
re\fuirements and other relevant provisions of Directive
1999/5/EC.
CAUTION:
Do not exposed to excessive heat such as
sunshine, fire or the like.
CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equiva-
lent type.
Anti-Theft System immobilizer
Hereby, CalsonicKansei Corp. declares that this ANT
ASSY-IMMOBILISER;model MW1014 is in compli-
ance with the essential re\fuirements and other
relevant provisions of Directive 1999/5/EC.
CAUTION:
Do not exposed to excessive heat such as
sunshine, fire or the like.
CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equiva-
lent type.
FOR CROATIA
Remote keyless entry system (if e\fuipped\b
JVT0008X
Technical information9-9
RADIO APPROVAL NUMBER AND
INFORMATION
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
Anti-Theft System immobilizer
J\fT0012\b
FOR CHINA
Remote keyless entry system (if equipped)
J\fT0005\b
Intelligent Key system (if equipped)
J\fT0006\b
Technical information9-11
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
FOR MOROCCO
Remote keyless entry system (if eq\fipped)
\bVT0025X
\bVT0108X
Anti-Theft System immobilizer
\bVT0026X
FOR \bORDAN
Remote keyless entry system (if eq\fipped)
Man\ffact\frer:
ALPS ELECTRIC CO.,LTD.
Model:
TWC1G124
Type approval No.:
TRC/LPD/2008/125
Anti-Theft System immobilizer
Man\ffact\frer:
Calsonic Kansei Corporation
Model:
MW1014
Type approval No.:
TRC/LPD/2009/86
FOR SOUTH AFRICA
Remote keyless entry system (if eq\fipped)
\bVT0038X
\bVT0039X
Technical information9-13
&RQGLWLRQ