RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Injection Service Manual

13B-41
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF012
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE No. 2
1.DEF : sensor reference voltage too weak
2.DEF : sensor reference voltage too high
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to start the engine
several times.
Special notes:
If the fault is present:
– the EGR functions and passenger compartment heating resistance functions
are inhibited,
– the engine speed is limited,
–the level 1 warning light is lit.
– The OBD warning light will come on after three consecutive cycles
(starting + 5 seconds + switch off the ignition and wait 40 seconds).
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged. Follow the procedure described in the
Wiring Check in the Introduction. This check enables the condition and the conformity of the engine wiring
harness to be checked.
The sensors connected to supply no.2 are:
–EGR valve position sensor,
–track 2 of the accelerator pedal potentiometer sensor,
–refrigerant pressure sensor.
To locate a faulty sensor and/or connection, disconnect one of these sensors then check whether the fault
becomes stored.
If the fault is still present, repeat the operation with the other sensors.
(wait a few seconds between each disconnection to allow the computer to perform the measurement).
If the fault is stored after a disconnection, replace the faulty sensor or repair its connection.
Clear the faults created by the multiple disconnections.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF012/EDC16_V48_DF012/EDC16_V4C_DF012

13B-42
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF012
CONTINUED
If the fault is still present when the three sensors have been disconnected:
1. Check the insulation from earth of the following connections:
Injection computer brown 48-track connector B, track F4 Track 2 of the EGR valve connector
Injection computer brown 48-track connector B, track J2 Track 6 of the EGR valve connector
Injection computer black 32-track connector A, track F2 Track 2 of the accelerator pedal
potentiometer gang 2
Injection computer black 32-track connector A track F3 Track 1 of the accelerator pedal
potentiometer gang 2
Injection computer, brown 48-track connector B, track F3 Track B of the refrigerant pressure
sensor
Injection computer, brown connector B track F1 Track C of the refrigerant pressure
sensor
Repair if necessary.
2. Check the insulation from + 12 V of the following connections:
Injection computer brown connector B track F4 Track 2 of the EGR valve connector
Injection computer brown connector B, track J2 Track 6 of the EGR valve connector
Injection computer grey connector C track C2 Track 4 of the EGR valve connector
Injection computer black connector A track F2 Track 2 of the accelerator pedal
potentiometer gang 2
Injection computer black connector A track F3 Track 1 of the accelerator pedal
potentiometer gang 2
Injection computer black connector A track F4 Track 6 of the accelerator pedal
potentiometer gang 2
Injection computer brown connector B track F3 Track B of the refrigerant pressure sensor
Injection computer, brown connector B track F1 Track C of the refrigerant pressure sensor
Injection computer grey connector C track C3 Track A of the refrigerant pressure sensor
Repair if necessary.
3. Check the insulation between the following connections after disconnecting the sensors:
–tracks2 and 6 of pedal sensor gang 2 connector.
–tracks2 and 4 of the EGR valve position sensor connector.
–tracksA and B of the refrigerant pressure sensor.
If these checks do not produce the correct results, replace the faulty sensor(s).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-43
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF013
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE No. 3
1.DEF : sensor reference voltage too weak
2.DEF : sensor reference voltage too high
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to start the
engine several times.
Special notes:
If the fault is present:
– the EGR function is inhibited,
– the engine speed is limited,
–the level 2 warning light is lit.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This check enables the condition and the conformity of the engine wiring harness to be checked.
The sensors connected to supply no. 3 are:
–Rail Pressure Sensor
–Air flow sensor..
To locate a faulty sensor and/or connection, disconnect one of these sensors then check whether the fault
becomes stored.
If the fault is still present, start the operation again with the other sensor.
(wait a few seconds between each disconnection to allow the computer to perform the measurement).
If the fault is stored after a disconnection, replace the faulty sensor or repair its connection.
Clear the faults created by the multiple disconnections.
If the fault is still present when both these sensors have been disconnected:
1. Check the insulation from earth of the following connections:
Injection computer brown 48-track connector B, track G3 Track 2 of the rail pressure sensor
Injection computer brown 48-track connector B, track A4 Track 3 of the rail pressure sensor
Injection computer brown 48-track connector B, track G1 Track 5 of the air flowmeter
Injection computer brown 48-track connector B, track B4 Track 3 of the air flowmeter
Injection computer brown 48-track connector B, track E2 Track 2 of the air flowmeter
Repair if necessary.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF013/EDC16_V48_DF013/EDC16_V4C_DF013

13B-44
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF013
CONTINUED
2. Check the insulation from + 12 V of the following connections:
Injection computer brown 48-track connector B track G3 Track 2 of the rail pressure sensor
Injection computer brown 48-track connector B, track A4 Track 3 of the rail pressure sensor
Injection computer brown 48-track connector B, track C4 Track 1 rail pressure sensor
Injection computer brown 48-track connector B, track G1 Track 5 of the air flowmeter
Injection computer brown 48-track connector B, track B4 Track 3 of the air flowmeter
Injection computer brown 48-track connector B, track E2 Track 2 of the air flowmeter
Injection computer brown 48-track connector B, track L4 Track 6 of the air flowmeter
Repair if necessary.
3. Check the insulation between the following connections after disconnecting the sensors:
–tracks1 and 3 of the rail pressure sensor,
–tracks2 and3 of the air flow sensor connector.
If these checks do not produce the correct results, replace the faulty sensor(s).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-45
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF015
PRESENT
OR
STOREDMAIN RELAY control CIRCUIT
1.DEF : relay cut out too soon
2.DEF : relay cut out too late
NOTESConditions for applying the fault finding procedure to a stored fault:
Only deal with this fault if it is stored.
Special notes:
The main relay is integrated into the UPC.
Use bornier Elé. 1681 for all operations on the injection computer connectors.
Check the Protection and Switching Unit connections.
Check the injection computer connections.
Repair if necessary.
Check the condition of the battery terminals making sure they are correctly tightened.
Repair if necessary.
Check for continuity and the absence of interference resistance on the following
connection:
Injection computer connector B,
brown 48-track track E1 Track D2 UPC brown connector D.
Repair if necessary.
IMPORTANT!If the fault is still present and remains present, refer to the Protection and Switching Unit
Technical Note.
WARNING
If the UPC no longer detects the injection computer frames then GMV 1 will be
started until the battery has been completely discharged.
In the event that engine cooling fan 1 is not working, GMV 2 will be supplied.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF015/EDC16_V48_DF015/EDC16_V4C_DF015

13B-46
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF017
PRESENT
OR
STOREDPRE-POSTHEATING UNIT CONTROL CIRCUIT
CC.1 : short circuit to + 12 V
CC.0 : open circuit or short circuit to earth
CO : open circuit
1.DEF : internal electrical fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after actuator command AC001 Preheating unit, or after
an attempted engine start.
Special notes:
If the fault is present, it is difficult or even impossible to start the vehicle when cold.
Use bornier Elé. 1681 for all operations on the injection computer connectors.
CC.1
NOTESNone.
Check the pre-postheating unit connections and the heating plug supply cables.
Check the injection computer connections.
Repair if necessary.
Check the condition of the F2 (70A) supply fuse on the power supply fuse board.
Check the continuity and insulation against + 12 V of the following connections:
Injection computer grey 32-track connector C, track E2 Track 8 preheating unit
Injection computer grey 32-track connector C, track A4 Track 3 preheating unit
Repair if necessary.
If the fault is still present, replace the pre-postheating unit.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF017/EDC16_V48_DF017/EDC16_V4C_DF017

13B-47
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF017
CONTINUED
CC.0
CO
NOTESSpecial notes:
If the pre-postheating unit has a short circuit to earth there is
a risk that the heater plugs will be operated continuously.
The heater plugs and the engine may be damaged.
Check the pre-postheating unit connections and the heating plug supply cables.
Check the injection computer connections.
Repair if necessary.
Check the condition of the F2 (70A) supply fuse on the power supply fuse board.
Check the continuity and insulation against earth of the following connection:
Injection computer grey 32-track connector C, track A4 Track 3 preheating unit
Injection computer grey 32-track connector C, track E2 Track 8 preheating unit
Repair if necessary.
If the fault is still present, replace the pre-postheating unit.
1.DEF
NOTESNone.
Check the pre-postheating unit connections and the heating plug supply cables.
Check the injection computer connections.
Repair if necessary.
Check the condition of the F2 (70A) supply fuse on the power supply fuse board.
Check for continuity and the absence of interference resistance on the following connection:
Injection computer grey 32-track connector C, track E2 Track 8 preheating unit
Repair if necessary.
If the fault is still present, check that the computer output is working correctly.
with the pre-postheating unit connected:
– connect the negative terminal of the voltmeter to track 8 of the preheating unit,
– connect the positive terminal of the voltmeter to the + 12 V battery,
– run command AC001 Pre-postheating unit.
If the voltmeter does not indicate the battery voltage while the command is running (ten one-second ON/OFF
cycles), contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-48
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF025
PRESENT
OR
STOREDPRE-POSTHEATING UNIT DIAGNOSTIC LINE
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after several attempts to start the engine, or following
actuator command AC001 Preheating unit.
Special notes:
It is difficult or even impossible to start the engine when cold.
Use bornier Elé. 1681 for all operations on the injection computer connectors.
Check the pre-postheating unit connections.
Check the connections on all the heater plugs.
Repair if necessary.
Check the resistance of the heater plugs:
Replace any plug whose resistance is not below 2Ω at + 20°C.
Check the continuity and absence of interference resistance of the following connections:
– Preheating unit track 1 Heater plug of cylinder 3
– Preheating unit track 2 Heater plug of cylinder 4
– Preheating unit track 6Heater plug of cylinder 1
– Preheating unit track 7 Heater plug of cylinder 2
Check for the presence of +12V battery on track 3 of the preheating relay (via maxi fuse).
Check the engine earthing.
If the fault is still present,
Check the injection computer connections.
Check for continuity and the absence of interference resistance on the following connection:
Injection computer, grey 32-track connector C, track A4 Track 9 preheating unit connector
If the fault is still present, replace the pre-postheating unit.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF025/EDC16_V48_DF025/EDC16_V4C_DF025

13B-49
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF037
PRESENT
OR
STOREDENGINE IMMOBILISER
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after a road test or an attempt to start the engine.
Special notes:
It is impossible to start the vehicle.
Use bornier Elé. 1681 for all operations on the injection computer connectors.
Check the UCH connections.
Check the injection computer connections.
Repair if necessary.
Test the multiplex network and carry out a complete fault finding procedure on the UCH.
Refer to the UCH Technical Note if a fault is declared present.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF037/EDC16_V48_DF037/EDC16_V4C_DF037

13B-50
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF038
PRESENT
OR
STORED
COMPUTER
CO : open circuit
1.DEF : permanent high signal
2.DEF : permanent low signal
3.DEF : configuration absent or incorrect
4.DEF : analogue/digital converter fault
5.DEF : EEPROM fault
6.DEF : activation in Watchdog
7.DEF : signal outside upper limit
8.DEF : signal outside lower limit
9.DEF : disrupted communication
10.DEF : injector control condenser fault
11.DEF : injector control
12.DEF : Initialisation fault
13.DEF : deceleration fault when decelerating
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after several starting attempts, or with the engine running.
Special notes:
The level 1 warning light is lit for a fault that does not require you to stop the vehicle.
The level 2 warning light is lit for a fault which requires the engine to be switched off.
If 5.DEF is still present, the OBD warning light will come on after three consecutive
driving cycles (starting + 5 seconds + switch off the ignition and wait 40 seconds).
Use bornier Elé. 1681 for all operations on the injection computer connectors.
CO
1.DEF
to
9.DEF
11.DEF
to
13.DEFCheck the injection computer connections and the continuity of all the supplies.
Repair if necessary.
Clear the faults.
Switch off the ignition, wait 30 seconds and switch the ignition on again.
If the fault is still present, contact the Techline and fill out the fault finding log included
in this Technical Note.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF038/EDC16_V48_DF038/EDC16_V4C_DF038