brake light RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Injection Workshop Manual

13B - 24
DIESEL INJECTION
Fault finding - Fault summary table13B
V10 MR-372-J84-13B150$235.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
Tool
faultAssociated
DTCDiagnostic tool titleLevel 1
fault warning
light (Orange
heater plugs
“on” indicator
light)Level 2 fault
warning light
(Red overheating
warning light)No fault
warning
light litOBD
warning
light lit
DF040 201Cylinder 1 injector circuit CO CC.1 / CC / 1.DEF ... CO
DF041 202Cylinder 2 injector circuit CO CC.1 / CC / 1.DEF ... CO
DF042 203Cylinder 3 injector circuit CO CC.1 / CC / 1.DEF ... CO
DF043 204Cylinder 4 injector circuit CO CC.1 / CC / 1.DEF ... CO
DF046 560Battery voltage ... ... 1.DEF/2.DEF ...
DF047 615Computer feed voltage ... ... X ...
DF049 530Refrigerant sensor circuit ... ... CC.1/CO.0 ...
DF050 571Brake switch circuit ... ... 1.DEF/2.DEF ...
DF051 575Cruise control/speed limiter
function... ... 1.DEF /
2.DEF /
3.DEF...
DF053 89Rail pressure regulation function 3.DEF / 8.DEF CC.0 / CC.1 / CO /
1.DEF / 2.DEF /
5.DEF / 6.DEF / 7.DEF4.DEF ...
DF054 33Turbocharging solenoid valve
control circuitCO/CC.0/CC.1/
1.DEF... ... ...
DF055 243Turbocharging pressure
regulation circuit1.DEF/2.DEF ... ... ...
DF056 100Air flow sensor circuit 3.DEF/4.DEF ... CC.0/CC.1/
1.DEF/2.DEF
DF057 2264Water in diesel fuel detector
circuit... ... X ...
DF067 638Damper control circuit ...
CC.0OC / CC.1 /
1.DEF...
DF069 1620Impact detected signal X
DF070 830Clutch switch circuit ... ... 1.DEF/2.DEF ...

13B-36
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 4C
DF008
CONTINUED 2
2.DEF
NOTESOnly in Vdiag 4C.
Check the mechanical condition of the accelerator pedal:
– locked in full load position,
– with the pedal blocked by an external component.
Check the brake light switch.
Repair if necessary.
Vary the position of the pedal and refer to the conformity check in order to check the operating values of the
accelerator pedal potentiometer.
If the values displayed are inconsistent, replace the accelerator pedal potentiometer.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.

13B-179
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
EDC16_V44_ET704/EDC16_V48_ET704/EDC16_V4C_ET704/
EDC16_V44_ET705/EDC16_V48_ET705/EDC16_V4C_ET705
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
ET704
ET705
BRAKE SWITCH NO. 1
BRAKE SWITCH NO. 2
NOTESSpecial note:
Statuses ET704 and ET705 should change status at the same time. In the event of
inconsistency, refer to the interpretation of fault DF050 Brake switch circuit.
ACTIVE
OR
INACTIVEIf the brake lights are working:
check the continuity and make sure there is no interference resistance on the following
connection:
Connection code 5A between components 160 and 120/645/119.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the condition and conformity of the brake light fuse,
– the conformity of the values in the following table:
disconnect the switch and carry out the following checks:
For Mégane II and Scénic II with ESP
Continuity between
connectionsInsulation between
connections
Switch pressed
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
For Mégane II and Scénic II without ESP
Continuity between
connectionsInsulation between
connections
Switch pressed
(Brake pedal released)5A and BPT 65A and SP17
Switch released
(Brake pedal depressed)65A and SP17 5A and BPT
Replace the switch if the values obtained are not correct