RENAULT TWINGO RS 2009 2.G Chasiss ESP Service Manual

38C-41
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF087
PRESENT
OR
STOREDPROGRAMMING THE STEERING WHEEL ANGLE SENSOR
DEF: Programming not performed
NOTESNone.
Position the steering wheel horizontally and the front wheels set straight ahead.
Check and store the internal fault code of component 583 using parameter PR113 Steering wheel angle sensor
internal fault code.
The internal fault code of the steering wheel angle sensor must be 0, 10 or 11, if it is different, replace
component 583 (see MR 411, Mechanical, 36A, Steering assembly, Steering column, Removal - Refitting).
Calibrate component 583 using command VP003 Steering wheel angle sensor (see Configurations
and programming).
Clear the ESP sensor offsets using command RZ011 Sensor offsets.
Check the value of parameter PR033 Steering wheel angle.
The steering wheel angle value must be close to 0˚ ± 5˚.
ESP_V05_DF087

38C-42
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF090
PRESENT
OR
STOREDFRONT RIGHT-HAND WHEEL TARGET
NOTESPriorities when dealing with a number of faults:
Deal with fault DF026 Front right-hand wheel speed sensor circuit first if it is
present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Visually inspect the condition of the axle assemblies (impacts, deformations etc.) and the conformity and good
condition of the tyre mountings (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres, Identification
and Tyre pressure, Identification).
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in good
condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution (0.4 < front wheel air gap < 1.7 mm).
If the air gap is incorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly if necessary (see MR 411, Mechanical,
31A, Front axle components, Hub carrier bearing: Removal - Refitting).
If the air gap is correct.
–Swap both front wheel speed sensors.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF090 has become DF091 Front left-hand wheel target, replace the magnetic
target (see MR 411, Mechanical, 31A, Front axle components, Front hub carrier bearing: Removal –
Refitting).
–If the fault remains on the same side, replace component 152 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Front wheel speed sensor, Removal - Refitting).
ESP_V05_DF090

38C-43
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF091
PRESENT
OR
STOREDFRONT LEFT-HAND WHEEL TARGET
NOTESPriorities when dealing with a number of faults:
Deal with fault DF006 Front left wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Visually inspect the condition of the axle assemblies (impacts, deformations etc.) and the conformity and good
condition of the tyre mountings (see MR 411, Mechanical systems, 35A, Wheels and tyres, Tyres,
Identification and Tyre pressure, Identification).
Replace the tyre(s) if necessary (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres, Removal - Refitting).
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in good
condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution (0.4 < front wheel air gap < 1.7 mm).
If the air gap is incorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly if necessary (see MR 411, Mechanical,
31A, Front axle components, Hub carrier bearing: Removal - Refitting).
If the air gap is correct.
–Swap both front wheel speed sensors.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF091 has become DF090 Front right-hand wheel target, replace the magnetic
target (see MR 411, Mechanical, 31A, Front axle components, Front hub carrier bearing: Removal –
Refitting).
–If the fault remains on the same side, replace component 153 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Front wheel speed sensor, Removal - Refitting).
ESP_V05_DF091

38C-44
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF092
PRESENT
OR
STOREDREAR RIGHT-HAND WHEEL TARGET
NOTESPriorities when dealing with a number of faults:
Deal with fault DF027 Rear right-hand wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Visually inspect the condition of the axle assemblies (impacts, deformations etc.) and the conformity and good condition
of the tyremountings (seeMR 411, Mechanical systems, 35A, Wheels and tyres, Tyres, IdentificationandTy re
pressure, Identification).
Re place the tyre(s) if necessary (seeMR 411, Mechanical, 35A, Wheels and tyres, Tyres, Removal - Refitting).
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in good
condition.
ESP_V05_DF092

38C-45
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF092
CONTINUED
Check that the wheel speed sensor mounting is in good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
For versions equipped with disc brakes:
Check the sensor/target air gap through one wheel revolution (0.1 < rear wheel air gap < 0.9 mm).
If the air gap is incorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
If the air gap is correct.
–Swap both rear wheel brake discs as well as the brake pads.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF092 has become DF093 Rear left-hand wheel target, replace
the instrumented bearing/wheel sensor mounting assembly (see MR 411 Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Wheel speed sensor, Removal - Refitting).
For versions equipped with drum brakes:
–Swap both rear wheel brake drums.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF092 has become DF093 Rear left-hand wheel target, replace the target
(see MR 411, Mechanical, 33A, Rear axle components, Rear brake drums, Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).

38C-46
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF093
PRESENT
OR
STOREDREAR LEFT-HAND WHEEL TARGET.
NOTESPriorities when dealing with a number of faults:
Deal with fault DF007 Left rear wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Visually inspect the condition of the axle assemblies (impacts, deformations etc.) and the conformity and good
condition of the tyre mountings (see MR 411, Mechanical systems, 35A, Wheels and tyres, Tyres,
Identification and Tyre pressure, Identification).
Replace the tyre(s) if necessary (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres, Removal - Refitting).
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in good
condition.
ESP_V05_DF093

38C-47
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF093
CONTINUED
Check that the wheel speed sensor mounting is in good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
For versions equipped with disc brakes:
Check the sensor/target air gap through one wheel revolution (0.1 < rear wheel air gap < 0.9 mm).
If the air gap is incorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
If the air gap is correct.
–Swap both rear wheel brake discs as well as the brake pads.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF093 has become DF092 Rear right-hand wheel target, replace
the instrumented bearing/wheel sensor mounting assembly (see MR 411 Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
–If the fault remains on the same side, replace component 151 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Wheel speed sensor, Removal - Refitting).
For versions equipped with drum brakes:
–Swap both rear wheel brake drums.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the initially declared fault DF093 became DF092 "Rear right-hand wheel target " , replace the target
(see MR 411 Mechanical system, 33A, Rear axle components, Rear brake drums, removal-refitting).
–If the fault remains on the same side, replace component 151 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).

38C-48
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF098
PRESENT
OR
STOREDNO UCH MULTIPLEX SIGNAL
NOTESSpecial notes:
Even though this is stored in the computer, this fault does not cause the warning lights
to come on or a fault message, because the ESP system is not faulty.
Perform fault finding on the UCH (Passenger compartment connection unit) using
the diagnostic tool.
Note:
After repairing the fault in the UCH (Passenger compartment connection unit),
clear the fault memory in the ESP system.
Priority in the event of a number of faults:
Deal with fault DF152 Multiplex network first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Check the UCH (Passenger compartment connection unit) using the diagnostic tool (see 87B, Passenger
compartment connection unit).
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF098

38C-49
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF099
PRESENT
OR
STOREDPRIVATE MULTIPLEX NETWORK
NOTESUse the Wiring Diagram Technical Note for New Twingo.
Check the connection and condition (possible wiring damage) of the connectors of components 1094 and 1175.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair), repair the connector, otherwise replace the wiring.
Check for a voltage of 12 V between connections MAM and AP5 of component 1175.
Is the voltage measured correct?
YESConnector of component 583 and intermediate union R107 disconnected.
Check the insulation and continuity of connections 4AP and 4AH between
component 1175 and the intermediate union R107.
Check the insulation and continuity of connections 4AP and 4AH between
intermediate union R107 and component 1094.
If the connections are faulty (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the checks do not reveal any faults, replace component 1175 (see MR 411,
Mechanical, 38C, Anti-lock braking system, Lateral acceleration and yaw speed
sensor, Removal - Refitting).
NOCheck the condition and position of fuse F10 (5A) in the passenger compartment
fuse and relay box (see 81C, Fuse box).
Connectors of components 1175, 583, 1094 and intermediate union R107
disconnected.
Check the insulation and continuity of connection MAM of component 1175.
Check the insulation and continuity of connection AP5 between
components 1016 and 1175.
Check the insulation and continuity of connection AP5 between component 1094
and intermediate union R107.
If the connections are faulty (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
ESP_V05_DF099

38C-50
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF100
PRESENT
OR
STOREDNO STEERING WHEEL ANGLE MULTIPLEX SIGNAL
NOTESUse the Wiring Diagram Technical Note for New Twingo.
Check that the connections and location of any special fittings (CB, car phone, amplifier, etc.) are not preventing
the system from working correctly.
With the ignition on, check for 12 V between connections NAM and AP5 of component 583.
Is the voltage measured correct?
YESConnectors of components 1175, 1094, 583 and intermediate union
R107 disconnected.
Check the insulation and continuity of connections 4AP and 4AH between
component 583 and intermediate union R107.
Check the insulation and continuity of connections 4AP and 4AH between
intermediate union R107 and component 1094.
If the connections are faulty (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
NOCheck the condition and position of fuse F10 (5A) in the passenger compartment fuse
box (see 81C, Fuse box).
Check the connection and condition (possible wiring damage) of the connectors of
components 583 and 1016.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Connectors of components 1175, 1094, 583 and intermediate union
R107 disconnected.
Check the insulation and continuity of connection AP5 between component 1016
and component 583.
Check the continuity and insulation of connection AP5 between component 1094
and intermediate connector R107.
Check the continuity and insulation of connection NAM between component 583
and the chassis earth (tightness, oxidation, etc.).
If the connections are faulty (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
ESP_V05_DF100