fuse box RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Owner's Guide

87B -100
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET047
BRAKE PEDAL POSITION
NOTESNo faults should be present or stored.
SPECIFICATIONSPRESSED
RELEASED
Check the presence and condition of fuse F5 (15 A) in the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the brake pedal switch 4-track connector (component code 160).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
On component 160, with the brake pedal depressed, check the continuity between connections AP10 and 5A
and the insulation of connections AP10 and 65A.
On component 160, with the brake pedal released, check the continuity between connections AP10 and 65A
and the insulation between connections AP10 and 5A.
Replace the switch if faulty. (See MR 411 mechanical systems 37A, Mechanical component controls, Brake
light switch: Removal - Refitting).
Check the condition and connection of connector PE1 of the UCH (component code 645) (tabs bent, oxidised,
broken).
Check for + 12 V (+ battery feed) on connection AP10 of the brake switch connector (component code 160).
If it is not correct, check the insulation, continuity and the absence of interference resistance of connection
AP10 between components 160 and 1016.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET047

87B -104
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
Windscreen wiper fault:ET077
WIPER STALK POSITION
NOTESNo faults should be present or stored.
Check the following configurations:
–Check that LC094 "Wiper intermittent speed ring" displays "With". If not, carry
out CF191 "Wiper intermittent speed ring".
–Check that LC096 "Automatic wiper function" displays "With". If not, carry out
CF194 "Automatic wiper function".
SPECIFICATIONSINTERMITTENT
LOW SPEED
HIGH SPEED
Check the condition and connection of the 3-track windscreen wiper motor connector (component code 212)
(broken, bent, oxidised tabs).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check that fuse F2 (15 A) is sound and correctly fitted to the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the UCH 40-track connector PE1 (component code 645) (tabs bent,
oxidised or broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Combined wiper-washer check:
●Connection code AP71 between components 145 and 1016.
●Connection code 14E (windscreen wiper timed control) between components 645 and 145.
●Connection code 14G (low speed windscreen wiper control) between components 645 and 145.
●Connection code 14H (high speed windscreen wiper control) between components 645 and 145.
●Connection code 36E (rear screen wiper timed control) between components 645 and 145.
●Connection code MAN or MAN between component 145 and the earth MAN (left-hand drive) or MAM
(right-hand drive).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the problem persists, replace the wiper stalk (component code 145). (See MR 411 mechanical systems 84A,
Controls - Signals, Wiper switch: Removal - Refitting).
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET077

87B -105
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET078
ET079
WINDSCREEN WASHER REQUEST
REAR SCREEN WASHER REQUEST
NOTESNo faults should be present or stored.
SPECIFICATIONSACTIVE
INACTIVE
Check that fuse F2 (15 A) is sound and correctly fitted to the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the 2-track connector on the bidirectional washer pump (component
code 677) (broken, bent, oxidised tabs).
Check the condition and connection of the UCH 40-track connector PE1 (component code 645) (tabs bent,
oxidised or broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Move the monolever (component code 209) to check the + 12 V, insulation, continuity and the absence of
interference resistance on the following connections:
Check the front and rear bidirectional washer pump:
●Connection code 16A between components 677 and 145.
●Connection code 24A between components 677 and 145.
●Connection code 16A between components 145 and 645.
●Connection code 24A between components 145 and 645.
If any of the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, supply the pump. If the pump does not work, replace the bidirectional washer pump
(component code 677). (See MR 411, mechanical systems, 85A, Washing wiping, Windscreen washer
pump: Removal - Refitting)
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET078 / UCH_V44_ET079

87B -106
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET080
REAR SCREEN WIPER REQUEST
NOTESNo faults should be present or stored.
Check the following configuration:
Check that LC096 "Automatic wiper function" displays "With". If not, carry out
CF194 "Automatic wiper function".
SPECIFICATIONSACTIVE
INACTIVE
Check that fuse F36 (15 A) is sound and correctly fitted to the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the 3-track rear screen wiper motor connector (component code 211)
(broken, bent, oxidised tabs).
Activate the rear screen wiper, check for + 12 V on connection 36A of the rear screen wiper
motor connector (component code 211).
Check that the earth on connection MYH of the rear screen wiper motor connector (component code 211) is in
perfect condition.
Check the condition and connection of the UCH 40-track connector PE1 (component code 645) (tabs bent,
oxidised or broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET080

87B -108
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET081
LIGHTING STALK POSITION
NOTESNo faults should be present or stored.
Check the following configurations:
–Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSHAZARD LIGHTS
SIDE
DIPPED
MAIN BEAM HEADLIGHTS
Check that fuses F13 (30 A), F15 (5 A) (without automatic headlighting) or F15 (15A) (with automatic
headlighting) is sound and correctly fitted in the passenger compartment fuse and relay box
(component code 1016).
Check the condition and connection of the monolever connector (component code 209) and the UCH 40-track
connector PE2 (component code 645) (tabs bent, broken or oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET081

87B -111
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
With automatic headlighting:ET082
REAR FOG LIGHTS REQUEST
NOTESNo faults should be present or stored.
Note:
The signal can only be interpreted if the function is managed by the UCH
(vehicle equipped with one-touch fog light control)
Check the following configurations:
Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSPRESENT
ABSENT
Check the presence and condition of fuses F15 (5 A), F20 (15 A), F25 (5 A), F39 (10 A) on the passenger
compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the correct positioning and condition of the bulb concerned. Replace the light if necessary.
Check the condition and connection of the light concerned (bent, oxidised, broken tabs).
Check the condition and connection of the UCH PE2 connector (component code 645) (tabs bent, oxidised or
broken).
Check the condition and connection of the horn and lights switch connector (component code 209) (tabs bent,
oxidised, broken).
Check for + 12 V (when rear fog lights are requested) on connection 9P of components 172 and 173.
Check for earth on connection MF of component 172 and connection MG on component 173.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET082

87B-113
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET082
CONTINUED 2
Checking the monolever (component code 209):
Check the insulation, continuity and the absence of interference resistance on the following connection:
Check between the monolever (component code 209) and the UCH:
●Connection code 9B between components 645 and 209.
Check between the monolever (component code 209) and the passenger compartment fuse and relay box
(component code 1016):
●Connection code BPA2 between components 209 and 1016.
●Connection code BPA3 between components 209 and 1016.
●Connection code MAN or MAM between component 209 and earth MAN or MAM (depending on the driving
layout, right- or left-hand drive).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connections BPA2 and BPA3 of component 209. Check for earth on connection MAM
(for right-hand drive vehicles) or MAN (for left-hand drive vehicles) of component 209.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the feeds and the connections of the monolever (component code 209) are correct, replace the monolever
(component code 209). (See MR 411 mechanical systems 84A, Controls - Signals, Lighting and signals
switch: Removal - Refitting)
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.

87B-114
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET083
ET084
LEFT-HAND INDICATOR REQUEST
RIGHT-HAND INDICATOR REQUEST
NOTESNo faults should be present or stored.
Check the following configurations:
Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSPRESENT
ABSENT
Check that fuses F13 (30A) and F15 (5 A) are sound and correctly fitted in the passenger compartment fuse and
relay box (component code 1016).
Replace the fuse(s) if necessary.
Check the condition and connection of the monolever connector (component code 209) and the UCH 40-track
connector PE2 (component code 645) (tabs bent, broken or oxidised).
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET083 / UCH_V44_ET084

87B-116
MR-413-X44-87B000$624.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
ET085
HAZARD WARNING LIGHTS BUTTON
NOTESThere must be no present or stored faults.
Check the following configuration:
–Check that LC018 Hazard warning lights switched on by ABS is definitely With.
Otherwise, run CF024 Illumination of hazard warning lights by ABS.
SPECIFICATIONSDEPRESSED
RELEASED
Check the presence and condition of fuse F42 (10 A) in the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the central door locking/warning switch connector (component code 1391)
(tabs broken, bent, oxidised).
Check the condition and connection of the PE1 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V on connection LPD of the locking/warning switch (component code 1391).
Check for earth on connection MAN of the locking/warning switch (component code 1391).
Check for + 12 V on connection 64D (when there is a hazard warning lights request) on components 255, 267 and
172.
Check for earth on components 255, 267 and 172 (indicator lights).
Check for + 12 V on connection 64C (when there is a hazard warning lights request) of components 256, 268 and
173 (indicator lights). Check for earth on components 256, 268 and 173.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET085
MR-413-X44-87B000$624.mif
UCH
Vdiag No.: 44

87B-118
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET087
ONE-TOUCH WINDOW CONTROL/SUNROOF AUTHORISATION.
NOTESThere must be no present or stored faults.
Check the following configuration:
–Check that LC070 One-touch windows/SR* is With. Otherwise, perform CF173
One-touch windows/SR.
Authorisation by the UCH of the one-touch window winder and/or sunroof motor
function is present under the following conditions:
–+ ACCESSORIES FEED,
–+ AFTER IGNITION FEED,
–when the engine is running.
SPECIFICATIONSPRESENT
ABSENT
Check the condition and connection of the PE2 24-track UCH connector, (component code 645) (tabs bent,
broken, oxidised).
Check the condition and connection of the driver's electric window motor 6-track connector (component 203)
(tabs bent, broken, oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If there is an electric sunroof, check that fuse F26 (20 A) is sound and correctly fitted in the passenger
compartment fuse and relay box (component code 1016).
Check the condition and connection of the connectors for component 1512.
With an electric sunroof, check the condition and connection of 4-track connector 339 in the A-pillar and the
sunroof computer 12-track connector (tabs bent, broken, oxidised).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET087