lights RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Owner's Guide

87B-85
MR-413-X44-87B000$528.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table87B
*SR: Sunroof.
*RF: radio frequencyTool status Diagnostic tool title
ET084Right-hand indicator request
ET085Hazard warning lights button
ET087One-touch window/SR* authorisation
ET096Wiper intermittent speed ring position
ET097Rear screen wiper park position
ET109Reverse gear engaged
ET111Front fog lights request
ET114Wiping request via rain sensor
ET115Request to switch on lights by light sensor
ET142Engine operating phase
ET181Key allocated to the vehicle
ET185Key code received
ET186Short press on door closing button
ET189Long press on door opening button
ET193RF* signal from a key allocated to the vehicle
ET229Injection immobiliser code
ET239Ignition switch position
ET240Key frequency (in Hz)
ET250Injection
ET463Door(s) or tailgate

87B-96
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET044
ELECTRIC DOOR LOCK BUTTON
NOTESNo faults should be present or stored.
Only apply the checks if the PRESSED and RELEASED statuses are inconsistent
with the actual position of the electric door locking button.
SPECIFICATIONSPRESSED
RELEASED
Check the following configurations:
–Check that LC003 Deadlocking is With. Otherwise carry out CF009 Deadlocking.
–Check that LC040 Automatic locking when driving is With. Otherwise carry out CF108 Automatic locking
when driving.
–Check that LC093 Central door locking is W ith. Otherwise perform CF192 Central door locking.
Check that fuse F42 (10 A) is sound and correctly fitted to the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the door lock switch/hazard warning lights switch connector (component
code 1391) (bent, oxidised, broken tabs).
Check the condition and connection of the UCH PE1 and PE2 connectors (component code 645) (tabs bent,
oxidised or broken).
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V on deadlocking/warning switch connection LPD (component code 1391).
Check for the earth on connection MAN of the locking / hazard warning lights switch (component code 1391).
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET044

87B-97
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET044
CONTINUED
Check the insulation, continuity and the absence of interference resistance on the following connections and
press the central door locking button to check the signal status on the following connections using the
oscilloscope (see signal status in test1 “Central door locking”):
●Connection code 64F between components 645 and 1391.
●Connection code 64Q between components 645 and 1391.
●Connection code 20M between components 1391 and 645.
●Connection code 20AW between components 1391 and 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
On component 1391, with the lock button pressed, check the continuity between connections 20AW and MAN.
On component 1391, with the lock button released, check the insulation between connections 20AW and MAN.
If the fault is still present, replace the central door locking/hazard warning lights switch (component code 1391).
(See MR 411 84A, Controls - Signals, Hazard warning lights and central door locking:
Removal - Refitting).
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.

87B -108
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET081
LIGHTING STALK POSITION
NOTESNo faults should be present or stored.
Check the following configurations:
–Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSHAZARD LIGHTS
SIDE
DIPPED
MAIN BEAM HEADLIGHTS
Check that fuses F13 (30 A), F15 (5 A) (without automatic headlighting) or F15 (15A) (with automatic
headlighting) is sound and correctly fitted in the passenger compartment fuse and relay box
(component code 1016).
Check the condition and connection of the monolever connector (component code 209) and the UCH 40-track
connector PE2 (component code 645) (tabs bent, broken or oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET081

87B -109
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET081
CONTINUED 1
Checking the monolever (component code 209):
Check the insulation, continuity and the absence of interference resistance on the following connections:
Side lights:
With automatic headlighting:
●Connection code 78B between components 209 and 645.
●Connection code BPA2 between components 1016 and 209.
●Connection code BPA3 between components 1016 and 209.
●Connection code MAN or MAM between component 209 and earth MAN or MAM (depending on the driving
layout, right- or left-hand drive).
Dipped headlights:
With automatic headlighting:
●Connection code 78Q between components 209 and 645.
●Connection code BPA2 between components 1016 and 209.
●Connection code BPA3 between components 1016 and 209.
●Connection code MAN or MAM between component 209 and earth MAN or MAM (depending on the driving
layout, right- or left-hand drive).
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.

87B-110
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET081
CONTINUED 2
Main beam headlights:
With automatic headlighting:
●Connection code 11Q between components 209 and 645.
●Connection code 11R (headlight flash) between components 209 and 645.
●Connection code BPA2 between components 1016 and 209.
●Connection code BPA3 between components 1016 and 209.
●Connection code MAN or MAM between component 209 and earth MAN or MAM (depending on the driving
layout, right- or left-hand drive).
Fog lights:
With automatic headlighting:
●Connection code 8H (front fog light) between components 209 and 645.
●Connection code 9B (rear fog light) between components 209 and 645.
●Connection code BPA2 between components 1016 and 209.
●Connection code BPA3 between components 1016 and 209.
●Connection code MAN or MAM between component 209 and earth MAN or the (depending on the driving
layout, right- or left-hand drive).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the feeds, earth and connections are correct, replace the monolever (component code 209). (See MR 411
Mechanical systems 84A, Controls - Signals, Lighting and signals switch:
Removal - Refitting)
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.

87B -111
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
With automatic headlighting:ET082
REAR FOG LIGHTS REQUEST
NOTESNo faults should be present or stored.
Note:
The signal can only be interpreted if the function is managed by the UCH
(vehicle equipped with one-touch fog light control)
Check the following configurations:
Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSPRESENT
ABSENT
Check the presence and condition of fuses F15 (5 A), F20 (15 A), F25 (5 A), F39 (10 A) on the passenger
compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the correct positioning and condition of the bulb concerned. Replace the light if necessary.
Check the condition and connection of the light concerned (bent, oxidised, broken tabs).
Check the condition and connection of the UCH PE2 connector (component code 645) (tabs bent, oxidised or
broken).
Check the condition and connection of the horn and lights switch connector (component code 209) (tabs bent,
oxidised, broken).
Check for + 12 V (when rear fog lights are requested) on connection 9P of components 172 and 173.
Check for earth on connection MF of component 172 and connection MG on component 173.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET082

87B-112
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET082
CONTINUED 1
Rear fog lights check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
Right-hand rear fog light:
●Connection code 9P between components 172 and 230.
Left-hand rear fog light:
●Connection code 9P between components 173 and 230.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V (when there is a rear fog light request) on connection 9W of component 230. Check for + 12 V
on connection BP16 of component 230.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Rear fog lights relay check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code 9W between components 230 and 645.
●Connection code BP16 between components 230 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.

87B-114
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET083
ET084
LEFT-HAND INDICATOR REQUEST
RIGHT-HAND INDICATOR REQUEST
NOTESNo faults should be present or stored.
Check the following configurations:
Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSPRESENT
ABSENT
Check that fuses F13 (30A) and F15 (5 A) are sound and correctly fitted in the passenger compartment fuse and
relay box (component code 1016).
Replace the fuse(s) if necessary.
Check the condition and connection of the monolever connector (component code 209) and the UCH 40-track
connector PE2 (component code 645) (tabs bent, broken or oxidised).
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET083 / UCH_V44_ET084

87B-116
MR-413-X44-87B000$624.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
ET085
HAZARD WARNING LIGHTS BUTTON
NOTESThere must be no present or stored faults.
Check the following configuration:
–Check that LC018 Hazard warning lights switched on by ABS is definitely With.
Otherwise, run CF024 Illumination of hazard warning lights by ABS.
SPECIFICATIONSDEPRESSED
RELEASED
Check the presence and condition of fuse F42 (10 A) in the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the central door locking/warning switch connector (component code 1391)
(tabs broken, bent, oxidised).
Check the condition and connection of the PE1 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V on connection LPD of the locking/warning switch (component code 1391).
Check for earth on connection MAN of the locking/warning switch (component code 1391).
Check for + 12 V on connection 64D (when there is a hazard warning lights request) on components 255, 267 and
172.
Check for earth on components 255, 267 and 172 (indicator lights).
Check for + 12 V on connection 64C (when there is a hazard warning lights request) of components 256, 268 and
173 (indicator lights). Check for earth on components 256, 268 and 173.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET085
MR-413-X44-87B000$624.mif
UCH
Vdiag No.: 44