RENAULT TWINGO RS 2009 2.G Engine Diesel Injection Workshop Manual

13B-161
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET637NEW PUMP CHAMBER FILLING
STATUS DEFINITIONCOMPLETED: This status indicates that the new pump chamber filling has been
completed.
NOT COMPLETED: This status indicates that the new pump chamber filling has not
been completed.
Conformity check: Engine stopped, ignition on or engine running.
COMPLETED
OR
NO
COMPLETEDThe actuator AC212 "New pump chamber filling" must be controlled before the engine
start following the replacement of the high pressure pump (see NT5011A "Repriming
Delphi high pressure pumps on K9K engines").
DCM1.2_V48_ET637/DCM1.2_V4C_ET637/DCM1.2_V50_ET637/DCM1.2_V54_ET637/DCM1.2_V58_ET637/DCM1.2_V5C_ET637

13B-162
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET703CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS DEFINITIONINACTIVE: This status indicates that no button has been pressed.
INCREASE: This status indicates that the increase button is pressed.
DECREASE: This status indicates that the decrease button is pressed.
SUSPEND: This status indicates that the 0 is pressed.
RESUME: This status indicates that the R button is pressed.
Conformity check: Engine stopped, ignition on or engine running.
INACTIVEStatus ET703 becomes INACTIVE when none of the cruise control/speed limiter buttons
is pressed. These buttons are located on the steering wheel.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not display INACTIVE,
●check the condition of the cruise control/speed limiter ± button and the condition
of its connector.
●check the condition of the cruise control/speed limiter R/0 button and the
condition of its connector.
Repair if necessary.
INCREASEStatus ET703 becomes INCREASE when the + cruise control/speed limiter button is
pressed. This button is on the steering wheel, on the left-hand side.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not display INCREASE, check the condition of the cruise control/
speed limiter
± button, and the condition of its connector. Repair if necessary.
Measure the resistance of the button between connections 86M and 86G while
pressing on the + button.
If the resistance is not approximately 300 Ω, check the continuity of the connection when
the button is in the rest position.
If there is continuity, replace the
± control button (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal -
Refitting).
DCM1.2_V48_ET703/DCM1.2_V4C_ET703/DCM1.2_V50_ET703/DCM1.2_V54_ET703/DCM1.2_V58_ET703/DCM1.2_V5C_ET703

13B-163
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET703
CONTINUED 1
DECREASEStatus ET703 becomes DECREASE when the - button of the cruise control/speed limiter
is pressed. This button is on the steering wheel, on the left-hand side.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not display DECREASE, check the condition of the cruise control/
speed limiter
± button, and the condition of its connector.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the button between connections 86M and 86G while
pressing on the - button.
If the resistance is not approximately 100 Ω, check the continuity of the connection when
the button is not pressed.
If there is continuity, replace the
± control button (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal -
Refitting).
SUSPENDStatus ET703 becomes SUSPEND when the cruise control/speed limiter "0" button is
pressed. This button is located on the steering wheel, to the right.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not become SUSPEND, check the condition of the cruise control/
speed limiter "R/0" button and the condition of its connector.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the button between connections 86M and 86G while
pressing on the 0 button.
If the resistance is not about 0 Ω, replace the R/0 control button (see MR 364 (Mégane
II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR
417 (Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal
- Refitting).
If there is continuity, replace the R/0 control button (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal -
Refitting).

13B-164
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET703
CONTINUED 2
RESUMEStatus ET703 becomes RESUME when the cruise control/speed limiter "R" button is
pressed. This button is located on the steering wheel, to the right.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not change to RESUME, check the condition of the cruise control/
speed limiter R/0 button, and the condition of its connector.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the button between connections 86M and 86G while
pressing on the R button.
If the resistance is not approximately 900 Ω, check the continuity of the connection when
the button is not pressed.
If there is continuity, replace the R/0 control button (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal -
Refitting).

13B-165
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET704
ET705BRAKE SWITCH NO. 1BRAKE SWITCH NO. 2
STATUS DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE: This status indicates that the brake pedal is released.
Note:
Statuses ET704 and ET705 should change status at the same time. In the event of inconsistency, refer to the
interpretation of fault DF050 Brake switch circuit.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVE
OR
INACTIVEIf the brake lights are working, check the continuity and the absence of interference
resistance between the following connections:
–5A between components 160 and 120,
–BPT between components 160 and 645 (for Mégane II, Scénic II, Modus and Clio III),
–BPT2 between components 160 and 645 (for Kangoo 2),
–AP10 between components 160 and 1016 (for New Twingo),
–65A between components 160 and 645 (vehicle without ESP),
–65G between components 160 and 645 (vehicle with ESP).
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the brake lights are not operational, check:
–the condition and fitting of the brake switch,
–the condition and conformity of the brake lights fuse,
the conformity of the values in the following table:
DCM1.2_V48_ET704/DCM1.2_V4C_ET704/DCM1.2_V50_ET704/DCM1.2_V54_ET704/DCM1.2_V58_ET704/DCM1.2_V5C_ET704/
DCM1.2_V48_ET705/DCM1.2_V4C_ET705/DCM1.2_V50_ET705/DCM1.2_V54_ET705/DCM1.2_V58_ET705/DCM1.2_V5C_ET705

13B-166
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET704
ET705
CONTINUED
ACTIVE
OR
INACTIVE
CONTINUEDContinuity between
connectionsInsulation between
connections
Switch pressed
(Brake pedal released)5A and BPT or BPT2SP17 and 65G (with ESP)
SP17 and 65A (without
ESP)
Switch released
(Brake pedal depressed)SP17 and 65G (with ESP)
SP17 and 65A (without
ESP)5A and BPT or BPT2
Only for New TwingoContinuity between
connectionsInsulation between
connections
Switch pressed
(Brake pedal released)5A and AP10 65A and AP10
Switch released
(Brake pedal depressed)65A and AP10 5A and AP10
If the values obtained are not correct, replace the brake switch (see MR 417 Mechanics,
37A, Mechanical component controls, Brake light Switch: Removal - Refitting).

13B-167
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 54
ET741OPTIONAL VEHICLE SPEED RESTRICTION
STATUS DEFINITIONACTIVE: This status indicates that the optional speed limiting function is active.
INACTIVE: This status indicates that the optional speed limiting function is inactive.
NOTESSpecial note:
This status indicates whether the vehicle speed restriction is a customer option, using
command SC040 Speed limiter.
This status is valid only on Kangoo 2
Conformity check: Engine stopped, ignition on or engine running.
"ACTIVE"Vehicle speed restricted using command SC040 Speed limiter. See the interpretation
of parameter PR879 Maximum speed authorized to find the configured speed
restriction.
"INACTIVE"The vehicle has no optional speed restriction.
DCM1.2_V54_ET741

13B-168
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 54
*VU: Commercial vehicle
ET800FAST IDLE SPEED FUNCTION
STATUS DEFINITIONACTIVE: This status indicates that the fast idle speed function is active.
INACTIVE: This status indicates that the fast idle speed function is inactive.
NOTESSpecial note:
This status indicates if the fast idle speed function is activated after use of the command
SC041 Changing commercial vehicle idle speed.
This status is valid only on Kangoo 2.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVEIs the fast idle speed function active? See the interpretation of parameter PR878 Fast
idle speed to find the configured idle speed.
INACTIVEThe fast idle speed function is inactive.
DCM1.2_V54_ET800

13B-169V6 MR-413-X44-13B000$160.mif
13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
Tool parameterDiagnostic tool title
PR005EGR valve opening setpoint
PR008Rail reference pressure
PR010Idle speed regulation setpoint
PR017Fuel flow
PR030Accelerator pedal position
PR032Inlet pressure
PR035Atmospheric pressure
PR037Refrigerant pressure
PR038Rail pressure
PR051EGR valve position feedback
PR055Engine speed
PR059Inlet air temperature
PR063Fuel temperature
PR064Coolant temperature
PR074Battery voltage
PR077EGR valve position sensor voltage
PR078Inlet pressure sensor voltage
PR080Rail pressure sensor voltage
PR086Pedal potentiometer voltage gang 1
PR088Pedal potentiometer gang 2 voltage
PR089Vehicle speed
PR125Power consumed by the air conditioning compressor
PR130Cruise control setpoint
PR132Air flow
PR147Pedal potentiometer voltage gang 1
PR148Pedal potentiometer voltage gang 2
PR568Pedal position gang 1
PR569Pedal position gang 2
DIESEL INJECTION
Fault finding – Parameter summary table

13B-170V6 MR-413-X44-13B000$160.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR730Air flow sensor temperature
PR873Oil oxidation signal
PR878Increased idle speed
PR879Maximum authorised speed
PR932Rate of engine oil dilution
PR1015Oil service interval
Tool parameterDiagnostic tool title