ECU Seat Alhambra 2010 Owner's Guide

Child safety 52
Integrated child seat
Introduction
The integrated child seat is only suitable for children in Group 2 (15-25 kg)
and Group 3 (22-36 kg), according to the ECE-R 44 regulation.
Additional information and warnings:
xSeat belts Ÿpage 22
WARNING
Child travelling without their seat belt fastened or not secured using a suit-
able restraint system may sustain fatal injuries if the airbag is deployed.
xYou should always transport all children up to 12 years of age on the
rear seat.
xAlways disable the front passenger airbag if, in exceptional cases, you
have no alternative but to transport a child in a rear-facing child safety seat
on the front passenger seat.
xChildren must always be protected with a child restraint system suited
to their height and weight.
xAlways fasten children's seat belts correctly.
WARNING
Children must travel in a child seat appropriate to their weight and height
while the vehicle is in motion.
xChildren must always be protected with a child restraint system suited
to their height and weight.
xChildren must assume the proper sitting position and be properly
belted in while travelling.
xThe shoulder part of the seat belt must lie approximately on the centre
of the shoulder, never across the neck or the arm.
xThe seat belt must lie close to the upper part of the body.
xThe lap belt part must lie across the pelvis, not across the stomach, and
always fit closely.
xAllow the belt to retract until it fits tightly over the child's seat.
xNever hold children or babies on your lap.
xAlways use a child seat and the seat belt for children who are less than
1.5 metres tall. The normal seat belt could cause injuries to the abdominal
and neck areas.
xOnly one child may occupy a child seat.
xRead and follow the information and warnings provided by the child
seat manufacturer.
xNever leave an unsupervised child alone on a child seat or in the
vehicle.
xAll modifications to the integrated child seat must be carried out by a
specialist workshop.
xReplace the child seat or any seat components damaged or involved in
an accident.
WARNING
Loose objects could fly uncontrollably around the vehicle interior and
cause injuries in the event of an accident or sudden braking.
xDo not leave toys or other hard, loose objects on the child seat or on the
seat while the vehicle is in motion.
WARNING (continued)

Child safety55
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Seat belt guide handle
xSecure the seat belt guide handle to the side head restraint on the
window side. The guide handle is secured by a button.
xOpen the upper button on the seat belt guide handle and pass the belt
webbing below the side head restraint and through the guide handle.
xClose the button again.
Adjusting the belt routing
xGuide the automatic three-point seat belt below the side head restraint.
xPull the latch plate and slowly place the belt webbing across the child's
chest and lap.
xInsert the latch plate into the buckle for the appropriate seat and push it
down until it is securely locked with an audible click.
xPull the belt to ensure that the latch plate is securely engaged in the
buckle.
WARNING
The seat belt only offers maximum protection from severe or fatal injuries
when it is correctly positioned.
xChildren must assume the proper sitting position and be properly
belted in while travelling.
xThe shoulder belt must be positioned against the middle of the
shoulder.
xThe seat belt must lie flat and fit comfortably.
xAllow the belt to retract until it fits tightly over the child's seat.
xThe lap part of the seat belt must lie across the pelvis, never across the
stomach.
xOnly one child may occupy a child seat.
Removing the seat belt
Lowering the cushion
xPull the unlock lever Ÿfig. 34 on the cushion in the direction of the
arrow .
xPush the cushion down through the central area in the direction of the
arrow until it safely engages Ÿ. The side supports fold away automat-
ically.
Removing the side head restraint
xOpen the seat belt guide handle.
xGuide the seat belt by hand to pull the belt back in more easily and not
damage the trim.
xPush the head restraint up as far as it will go.
xFold the backrest of the rear seat forwards Ÿpage 137.
xRemove the head restraint along with the side head restraint.
xRemove the head restraint and side head restraint by pulling on it.
xFitting the head restraint.
Fig. 34 Integrated child
seats. lowering the
cushion.
AAA1
ABA2

Unlocking and locking85
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Attention: Depending on the selected function in the central locking
submenu Convenience, you may push the button twice Ÿpage 70 to
unlock all doors and the tailgate.
The vehicle key only locks and unlocks the vehicle if it is within range of the
vehicle and if the batteries have enough power. When locking, the vehicle's
indicators will blink.
If the driver's door is open, the vehicle cannot be locked with the key. If you
unlock the vehicle without opening any doors or the tailgate, it will lock again
automatically after a few seconds. This function prevents the vehicle from
remaining unlocked if the unlocking button is pressed by mistake.
Convenience open/close function
xSee "Electric windows: functions" Ÿpage 102.
xSee "Panorama sliding sunroof: operation" Ÿpage 106.
Locking and unlocking the vehicle from the inside
The central locking button is still operative when the ignition is switched off.
The central locking button is only deactivated if the "Safe" security system is
activated Ÿpage 88.
Please note the following when you use the central locking button to lock your
vehicle:
xDo not turn on the "Safe" security system Ÿpage 88.
xDo not turn on the antitheft alarm.
xIt will not be possible to open the doors or the tailgate from the outside
this may offer extra safety, when stopped at traffic lights for example.
FunctionHandling the buttons on the vehicle
Unlocking the vehicle.Press button . Keep it pushed for the
convenience opening.
Lock the vehicle.Press button . Keep it pushed for the
convenience locking function.
Unlocking the tailgate.Press button .
Open the sliding door.Ÿpage 92.
0
1
˜
0
Push the button Ÿfig. 48:
Unlocking the vehicle.
Lock the vehicle.
Fig. 48 In the driver door:
central locking button.
0
1

Unlocking and locking87
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a When unlocking the vehicle, all of the indicators blink twice; when locking,
they blink once.
If you unlock the vehicle without opening any doors or the tailgate, it will lock
again automatically after a few seconds.
Unlocking and opening the doors
xTake the handle of the corresponding door and touched the outside
button.
xDoor open.
Closing and locking the doors
xClose the driver's door.
xPress on the outermost button of the passenger or driver's side door
(Ÿpage 86, fig. 50 arrow) once. The vehicle locks with the "Safe" security
system Ÿpage 88. The door being operated must be closed.
xOperate the outermost button on the driver's or passenger door handle
twice to lock the vehicle without the "Safe" security system.
Locking and unlocking the tailgate
If the vehicle key is within the tailgate approach zone (Ÿpage 86, fig. 49)
this will be automatically unlocked when opened.
xOpen and close the tailgate normally Ÿpage 97.
The tailgate locks automatically after it is closed when there is no vehicle key
inside the vehicle.
Locking using the second vehicle key
If there is a key inside the vehicle, this can only be locked from the outside if
a second is key is detected in the approach zone outside the vehicle.
Automatically turning off sensors
When the vehicle is not locked or unlocked for a long period of time then the
approach sensors for the passenger door and rear doors are turned off auto-
matically.When the outside button of the door handle is repeatedly pressed while the
vehicle is locked, for example due to contact with the branches of a tree, all
of the exterior buttons on the side of the vehicle affected will be turned off for
30 minutes. If the only button affected is the driver's door button, only this
button is turned off.
The sensors are turned on again:
xAfter 30 minutes.
xALTERNATIVELY: The vehicle is unlocked using the remote control on
the key.
xALTERNATIVELY: The tailgate is opened.
Convenience functions
xFor convenience locking of all electric windows and the panorama sliding
sunroof, press and hold the button on the outside door handle for more than
two seconds.
xRelease the button to interrupt the function. Pushing the button immedi-
ately after releasing it will open all of the electric windows (safety function)
’ Ÿpage 102.
When a door is opened using the door handle, all of the settings activated in
the menu Configuration – Convenience Ÿpage 70 will be applied.
Caution
A strong jet of steam or water can activate a proximity sensor if a valid vehicle
key is within the approach zone. If at least one of the electric windows is open
and the sensor is triggered several times, convenience locking will begin. If
the jet of steam or water is stopped briefly and then directed at one of the
sensors again, it is possible that all of the windows will open Ÿpage 87,
“Convenience functions”.
0

Unlocking and locking 88
Note
If the vehicle battery or the battery in the vehicle key is flat, it is possible that
the vehicle cannot be locked or unlock using the KESSY system.
"Safe" security system
When the vehicle is locked, the "Safe" security system deactivates the door
handles and the central locking button making the vehicle difficult to open.
The doors cannot be opened from inside Ÿ.
When the "Safe" security system is turned off:
xThe vehicle can be opened and unlocked from the inside using an inside
door handle.
xThe vehicle may be unlocked from the inside by pushing the central
locking button.
xThe anti-theft alarm will be activated.
xThe vehicle interior monitoring system and the anti-tow system are deac-
tivated.Driver's door indicator light.
WARNING
Careless use of the "Safe" security system can cause serious injury.
xNever leave anybody inside the vehicle if this is locked using the key.
When the "Safe" security system is activated, doors cannot be opened
from the inside.
xWhen the doors are locked, it is difficult to get to passengers in the
passenger compartment in case of an emergency. Passengers could remain
trapped inside in case of emergency.
Antitheft alarm
The anti-theft alarm makes it more difficult to break into the vehicle or steal it.
The antitheft alarm is automatically turned on when the vehicle is locked with
the key.
FunctionNecessary operations
Locks the vehicle with the "Safe"
security system.Press the button once on the vehicle
key.
Locks the vehicle without the
"Safe" security system.
Press the button twice on the vehicle
key.
Press the central locking button on
the driver's door once.
1
1
1
When the vehicle is locked:Meaning
The red LED flashes for approximately 2
seconds at short intervals and then more
slowly.The "Safe" security system is
switched on.
The red LED flashes for about two sec-
onds then turns off. After 30 seconds, the
LED flashes again.The "Safe" security system is
switched off.
The red LED remains lit for about 30 sec-
onds.There is a fault in the locking
system. Contact a specialist
workshop.

Lights and visibility123
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xPull the sun blind by the handle Ÿpage 122, fig. 70 up to the top.
xHook both rings of the fastening rod in the spaces provided . Check
that the sun blind is securely hooked into the spaces provided when it has
been lowered .
xTo put the sun blind away, unhook it at the top and lower by hand Ÿ.
Caution
To prevent damage to the blind or the interior trim, do not lower the sun blind
“quickly”.
Heat-insulating glass windscreen*
The heat-insulating windscreens include a reflective infrared coating. The
section above the rear vision mirror has been left uncoated (communication
window) to allow electric components from the accessories shop to operate
correctly Ÿfig. 71.
The uncoated surface should be covered from inside or outside or have an
adhesive label attached, otherwise the electronic components may not
operate correctly.
AA
AB
AB
Fig. 71 Windscreen with reflective infrared and metal
coating and small window (red surface).

Seats and storage compartments 140
Convenient entry function for the third row of seats
The outer seats of the second row can be folded to make it easier to get in and
out of the third row of seats.
Folding down the seat of the second row
xIf necessary, open the belt loop and wind up the seat belt by hand.
xIf necessary, remove the side head restraint of the integrated child seat
Ÿpage 52.
xIf necessary, raise the armrests.
xRemove any objects located in the floor area of the second row of seats,
where applicable Ÿ.
xPush the head restraint down as far as it will go Ÿpage 10.
xPush the lever Ÿfig. 87 forwards and fold the backrest of the rear
seat. The seat can still be moved forwards when rear seat is folded completely
forwards Ÿ.
xAlways take care when entering and leaving the vehicle Ÿ.Repositioning the seat of the second row
xLift the backrest of the rear seat in an upright position. The entire seat
folds backwards Ÿ.
xMake sure that the rear seat is securely engaged so that the seat belts can
provide proper protection in the rear seats. The red mark Ÿfig. 87 should
no longer be visible Ÿ in “Folding down rear seats to create load space”
on page 147.
Emergency exit function
If the lever Ÿfig. 87 does not work, e.g. after an accident, the seats on
the second row can be folded forwards from the third row to allow occupants
of the third row of seats to get out of the vehicle Ÿ.
xPull handle Ÿfig. 87 back and fold the backrest of the rear seat. The
complete rear seat folds forward Ÿ.
WARNING
Careless or uncontrolled use of the convenient entry assistant may result
in severe injury and accident.
xNever use the convenient entry function when the vehicle is in motion.
xAvoid trapping or damaging the seat belt when folding the rear seats
back.
xKeep your hands, fingers, feet and other body parts out of the hinges
and the seat locking mechanism when folding and unfolding.
xMats or other objects can be caught in the hinges of the backrests or
rear seat. This could prevent the backrest from locking safely when posi-
tioned upright.
xAll backrests must engage correctly for the seat belts on the rear seats
to work properly. When the backrest of an occupied seat is not correctly
locked in place, the passenger can be thrust forward with the backrest in
case of sudden braking, sudden manoeuvres or an accident.
Fig. 87 Second row of
seats: convenient entry
function controls.
A1
A2
A1
A3

Seats and storage compartments143
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Head restraints
Adjusting the head restraints
All seats are equipped with a head restraint.
Adjusting height
xPush the head restraint up or down in the direction of the arrow with the
button pressed Ÿfig. 90 or Ÿfig. 91 Ÿ.
xThe head restraint must engage securely in position. There are three
possible positions on the second row of seats and two possible positions on
the third row of seats.
Correct adjustment of head restraints
Adjust the head restraint so that its upper edge is at the same level as the top
of your head, or as close as possible to the same level as the top of your head
and under no circumstances below eye level. Keep the back of your neck as
close as possible to the head restraint.
Adjusting the head restraint for short people
Lower the head restraint completely, even if your head is below its upper
edge. When the head restraint is at its lowest, it is possible that a small gap
remains between it and the backrest.
Adjusting the head restraint for tall people
Raise the head restraint completely.
WARNING
Travelling with the head restraints removed or improperly adjusted
increases the risk of severe or fatal injuries in the event of accidents and
sudden braking or manoeuvres.
xAlways fit and adjust the head restraint properly whenever a person is
occupying a seat.
xAll occupants must correctly adjust the head restraint according to
their height to reduce the risk of back injuries in the event of an accident.
The upper edge of the head restraint must be as close as possible to the
same level as the top of your head and under no circumstances below eye
level. Keep the back of your neck as close as possible to the head restraint.
Fig. 90 Adjusting the
front head restraints.
Fig. 91 Adjusting the rear
head restraints.
A1A1

Seats and storage compartments 146
Loading luggage compartment
Introduction
Always transport heavy loads in the trunk and place the seat backs in a
vertical position. Always use the fastening rings with suitable rope or straps.
Never overload the vehicle. Both the carrying capacity as well as the distribu-
tion of the load in the vehicle have effects on the driving behaviour and
braking ability Ÿ.
Additional information and warnings:
xAirbag system Ÿpage 33
xLight Ÿpage 113
xTranspor ting Ÿpage 13
xTo wi ng m o d e Ÿpage 260
xWheels and tyres Ÿpage 323
WARNING
When the vehicle is not in use or being watched, always lock the doors and
the tailgate to reduce the risk of serious injury or death.
xDo not leave children unwatched, especially when the tailgate is open.
Children could climb into the luggage compartment, close the tailgate from
inside and be unable to escape themselves. This could lead to serious
injury or death.
xNever allow children to play in or around the vehicle.
xNever transport people in the luggage compartment.
WARNING
Unsecured or incorrectly secured objects can cause serious injury in case
of a sudden manoeuvring or breaking or in case of an accident. This is espe-cially true when objects are struck by a detonating airbag and fired through
the vehicle interior. To reduce the risks, please note the following:
xSecure all objects in the vehicle. Always keep equipment and heavy
objects in the luggage compartment.
xAlways secure objects with suitable rope or straps so that they cannot
enter the areas around the frontal or side airbags in case of sudden braking
or an accident.
xWhile driving, always keep object compartments closed.
xDo not place hard, heavy or sharp objects inside the passenger
compartment, in open storage compartments, the rear shelf or on the
dashboard.
xRemove hard, heavy and sharp objects from clothes and pockets inside
the vehicle and store securely.
WARNING
The transport of heavy object changes vehicle handling and increases
braking distance. Heavy loads that have not been stored or secured
correctly could cause loss of control and result in serious injury.
xThe vehicle handling changes when transporting heavy objects due to
a change in the centre of gravity.
xDistribute the load as uniformly and as low down on the vehicle as
possible.
xStore heavy objects in the luggage compartment as far from the rear
axle as possible.
Caution
xHard objects on the shelf could chafe the wires of the heating element
and antenna of the rear window and cause damage.
xThe side window antenna could be damaged due to chafing from objects.
WARNING (continued)

Seats and storage compartments149
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWhen the seat is folded down, no adults or children should travel in it
Ÿ.
Putting the seats in the second row back in place
xPull lever Ÿpage 147, fig. 95 upwards and place the seatback in
vertical position. The entire seat folds backwards.
xPull on the rear seats and the backrest to ensure that they are correctly
locked in place and that the safety belt protection is guaranteed for rear seat
passengers.
Putting the seats in the third row back in place
xOpen the tailgate.
xPull on the handle Ÿpage 148, fig. 96 to put the seat tray back in
position.
xPull on the handle Ÿpage 148, fig. 96 . The entire seat folds back-
wards.
xPress on the seat tray in the backrest until it is held in position by its
magnets.
xOpen the sliding door.
xPut the backrest into position and press firmly until it clicks into place.
xPull on the rear seats and the backrest to ensure that they are correctly
locked in place and that the safety belt protection is guaranteed for rear seat
passengers.
WARNING
Folding and lifting the rear seats carelessly without paying attention could
cause serious injury.
xNever fold or lift the seats while driving.
xDo no trap or damage seat belts when raising the backrest.
xKeep your hands, fingers, feet and other body parts out of the hinges
and the seat locking mechanism when folding and unfolding.
xMats or other objects can be caught in the hinges of the backrests or
rear seat. This could prevent the seat or backrest from locking securely in
the vertical position.
xAll backrests must engage correctly for the seat belts on the rear seats
to work properly. When the backrest of an occupied seat is not correctly
locked in place, the passenger can be thrust forward with the backrest in
case of sudden braking, sudden manoeuvres or an accident.
xNo seat must be occupied if the backrest or seat is folded or not
correctly engaged.
Caution
Before folding the backrest of the rear seat, adjust the front seats so that the
head restraint or backrest do not hit them when it is folded.
Caution
xObjects placed in the footrest area in front of and behind the rear seats
can be damaged when seats are folded down or put back into position.
Remove any objects in the way before folding seats down or repositioning
them.
xObjects placed in the moulding on the back of the third row of seats can
be damaged when folding down the seats or putting them back into position.
Remove any objects in the way before folding seats down or repositioning
them.
xThe attachment elements and supports for the net partition placed on the
rail system can be damaged when folding down seats from the third row or
putting them back into position and these can also damage the seats them-
selves. Before folding down or repositioning the seats, remove the attach-
ment elements and supports for the net from the rail system.
A1
A2
A3
WARNING (continued)