heating Seat Cordoba 2005 Owner's Guide

127 Refuelling
Safety FirstControls and equipment Tips and Maintenance Technical Data
T
Ti
ip
ps
s aan
nd
d MMa
ai
in
nt
te
en
na
an
nc
ce
e
R
Re
ef
fu
ue
el
ll
li
in
ng
g
F
Fi
il
ll
li
in
ng
g tth
he
e tta
an
nk
k
General notes
The filler neck is located in the rear right-side panel.
The fuel tank cap turns freely to prevent it’s opening without a key.
Open the cover, hold the cap with one hand and next introduce the
key in the lock and turn it 180° to the left. At this moment the cap
should unscrew in a counter-clockwise direction.To close, screw the cap to the right until you hear a "click". Turn the
key without releasing the cap clockwise 180°. Remove the key and
close the cover.
The tank holds about 45 liters.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
As soon as the automatic nozzle, correctly operated, disconnects for the
first time, the tank is full. Do not continue filling since the expansion space
would be occupied. If it heats up the fuel could overflow.
After filling the tank, screw cap and close tank flap until it engages.
The cap is tied to an anti-loss cord.
N No
ot
te
e
Any fuel spillage should be wiped off the paint finish immediately, as the
paint could otherwise be damaged, especially if it is RME (“biodiesel”) fuel.
C
Ca
au
ut
ti
io
on
n
On vehicles with a catalytic converter, never drive until the fueltank is
completely empty. The irregular fuel supply can cause misfiring. This allows
unburnt fuel into the exhaust system, which can cause overheating and
damage to the catalyst.
K
CON-009Fig. 99

129 Refuelling
Safety FirstControls and equipment Tips and Maintenance Technical Data
Properties of RME
•RME is chemically produced from vegetable oil (predominantly
rapeseed oil) in a process whereby the oil is mixed with methanol
and converted, via a catalyst, into RME.
•RME is almost totally sulfur free. The combustion of RME thus
emits practically no sulfur dioxide (SO
2).
•Exhaust gas contains less
– carbon monoxide
– hydrocarbons
– particles (i.e. soot)
than with conventional diesel fuel.
All emission values are lower than legal requirements.
•RME fuel is biodegradable.
•Performance may be slightly lower.
•Fuel consumption may be slightly higher.
•RME can be used in temperatures down to approximately –10 °C.
•Diesel fuel must be added at ambient temperatures of less than
–10 °C to prevent deterioration to the biodiesel. The mixing ratio
of diesel to biodiesel must be approximately 50:50.
I If
f tth
he
e RRM
ME
E rra
at
ti
io
o eex
xc
ce
ee
ed
ds
s 550
0%
%,
, tto
oo
o mmu
uc
ch
h ssm
mo
ok
ke
e mma
ay
y bbe
e ffo
or
rm
me
ed
d.
.
•During the summer months, RME may be mixed with diesel at
any ratio.
K
Driving in winter
When using summer Diesel trouble may be experienced at
temperatures below
0 °C because the fuel thickens due to wax separation.
For this reason winter Diesel which is more resistant to cold is sold
during the winter in some countries, and this works correctly down
to between –15 °C and –22 °C approximately, depending on the
brand of fuel used.
The biodiesel available in countries with different climactic
conditions usually has different temperature characteristics.
Technical Service Centres or service stations in each country can
inform you of the specific characteristics of the respective diesel.
K
Filter preheating
The vehicle is fitted with a filter preheater. This will ensure that the
fuel system will remain operational down to about –25 °C,
provided that winter Diesel which is cold resistant down to –15 °C
is used.
If, at temperatures below –25 °C the fuel is waxed to such an
extent that the engine will not start it is sufficient to place the
vehicle in a warm enclosure for a while.
Fuela ad
dd
di
it
ti
iv
ve
es
s
(anti-waxing agent), petroland similar fluids must
n no
ot
t
be mixed with Diesel fuel.
K

133 Intelligent technology
Safety FirstControls and equipment Tips and Maintenance Technical Data
constantly compares them with the actual behaviour of the vehicle.
If the desired course is not being maintained (for instance, if the
car is starting to skid), then the ESP compensates automatically by
braking the appropriate wheel.
The forces acting on the braked wheel bring the vehicle back to a
stable condition. If the vehicle tends to oversteer, the system will
act on the front wheel on the outside of the turn.
N No
ot
te
e
•In order to ensure that ESP functions correctly, all four wheels must be
fitted with the same tyres. Any differences in the rolling radiusof the tyres
can cause the system to reduce engine power when this is not desired.
•Modifications to the vehicle (e.g. to the engine, the brake system, running
gear or any components affecting the wheels and tyres) could affectthe
efficiency of the ABS, EDL, ESP and TCS.
K
Anti-lock brake system (ABS)
The anti-lock brake system prevents the wheels locking during
braking
⇒chapter “Anti-lock brake system and traction control
ABS”.
K
Electronic differential lock (EDL)
The electronic differential lock helps prevent the loss of traction
caused if one of the driven wheels starts spinning.
EDL helps the vehicle to start moving, accelerate and climb a
gradient in slippery conditions where this may otherwise be
difficult or even impossible.
It uses the ABS sensors to monitor the speed of the driven wheels.
In case of an EDL fault the warning light for ABS lights up
⇒
chapter “Warning lamps”.
At speeds of up to approximately 80 km/h, it is able to balance out
differences in the speed of the driven wheels of approximately 100
rpm caused by a slippery road surface on one side of the vehicle. It
does this by braking the wheel which has lost traction and
distributing more driving force to the other driven wheel via the
differential.
To prevent the disc brake of the braked wheel from overheating,
the EDL cuts out automatically if subjected to excessive loads. The
vehicle will continue to function normally without EDL. For this
reason, the driver is not informed that the EDL has been switched
off.
The EDL will switch on again automatically when the brake has
cooled down.
• • IIt
t mmu
us
st
t bbe
e rre
em
me
em
mb
be
er
re
ed
d tth
ha
at
t TTC
CS
S cca
an
nn
no
ot
t dde
ef
fy
y tth
he
e lla
aw
ws
s oof
f pph
hy
ys
si
ic
cs
s.
. TTh
hi
is
s
s sh
ho
ou
ul
ld
d bbe
e kke
ep
pt
t iin
n mmi
in
nd
d,
, ppa
ar
rt
ti
ic
cu
ul
la
ar
rl
ly
y oon
n ssl
li
ip
pp
pe
er
ry
y aan
nd
d wwe
et
t rro
oa
ad
ds
s aan
nd
d wwh
he
en
n
t to
ow
wi
in
ng
g aa ttr
ra
ai
il
le
er
r.
.
• • AAl
lw
wa
ay
ys
s aad
da
ap
pt
t yyo
ou
ur
r ddr
ri
iv
vi
in
ng
g sst
ty
yl
le
e tto
o ssu
ui
it
t tth
he
e cco
on
nd
di
it
ti
io
on
n oof
f tth
he
e rro
oa
ad
ds
s aan
nd
d tth
he
e
t tr
ra
af
ff
fi
ic
c ssi
it
tu
ua
at
ti
io
on
n.
. DDo
o nno
ot
t lle
et
t tth
he
e eex
xt
tr
ra
a ssa
af
fe
et
ty
y aaf
ff
fo
or
rd
de
ed
d bby
y EES
SP
P tte
em
mp
pt
t yyo
ou
u iin
nt
to
o
t ta
ak
ki
in
ng
g aan
ny
y rri
is
sk
ks
s wwh
he
en
n ddr
ri
iv
vi
in
ng
g,
, tth
hi
is
s cca
an
n cca
au
us
se
e aac
cc
ci
id
de
en
nt
ts
s.
.
W
WA
AR
RN
NI
IN
NG
G


136Your vehicle and the environment
After the running-in period
•On vehicles with a rev counter* the maximum permissible engine
speed is shown by the beginning of the red zone on the rev
counter scale. The needle of the counter must not move into this
zone.
Extremely high engine revs will be automatically governed.
K
C Cl
le
ea
an
ni
in
ng
g tth
he
e eex
xh
ha
au
us
st
t ffu
um
me
es
s
Description
T
Th
he
e ppe
er
rf
fe
ec
ct
t ffu
un
nc
ct
ti
io
on
ni
in
ng
g oof
f tth
he
e ccl
le
ea
an
ni
in
ng
g ssy
ys
st
te
em
m ffo
or
r eex
xh
ha
au
us
st
t ffu
um
me
es
s
is of great importance for the environment-friendly functioning of
your vehicle.
Therefore, keep in mind the following points:
•Versions with a catalytic converter must only use unleaded fuel
⇒"Filling the tank" chapter.
•In vehicles with a catalytic converter never drive until the fuel
tank is completely empty. Irregular fuel supply can cause misfiring,
thus allowing unburned fuel into the exhaust system which can
cause overheating and damage to the catalyst.
•If you experience starting difficulties, loss of power or engine
problems while driving, the cause could be a failure in the ignition.
In this case, fuel may be entering the exhaust system withoutburning and, in this way being released into the atmosphere.
Furthermore, the catalyst could deteriorate due to overheating.
Reduce speed immediately. Have this problem fixed at the nearest
Technical Service Centre.
•Do not overload the engine with oil
⇒"Engine oil" chapter.
•Do not towstartthe vehicle for more than 50 m
⇒"Tow
start/towing" chapter.
N No
ot
te
e
Even when the cleaning system for exhaust fumes is in perfect working
order, under certain circumstances, the fumes may smell like sulfur.
This depends on the percentage of sulfur in the fuel.
Often it is sufficient to change brands or buy super unleaded.
K
•D Du
ue
e tto
o ppo
os
ss
si
ib
bl
le
e hhi
ig
gh
h tte
em
mp
pe
er
ra
at
tu
ur
re
es
s oof
f tth
he
e cca
at
ta
al
ly
ys
st
t,
, ddo
o nno
ot
t ppa
ar
rk
k iin
n
p pl
la
ac
ce
es
s wwh
he
er
re
e tth
he
e cca
at
ta
al
ly
ys
st
t iis
s eea
as
si
il
ly
y eex
xp
po
os
se
ed
d tto
o iin
nf
fl
la
am
mm
ma
ab
bl
le
e mma
at
te
er
ri
ia
al
l.
.
•D
Do
o nno
ot
t uus
se
e aad
dd
di
it
ti
io
on
na
al
l ppr
ro
ot
te
ec
ct
ti
io
on
n ffo
or
r tth
he
e bbo
od
dy
y oor
r aan
nt
ti
ic
co
or
rr
ro
os
si
iv
ve
e ppr
ro
od
du
uc
ct
ts
s ffo
or
r
s su
um
mp
ps
s aan
nd
d eex
xh
ha
au
us
st
t ppi
ip
pe
es
s,
, c
ca
at
ta
al
ly
yt
ti
ic
c cco
on
nv
ve
er
rt
te
er
rs
s oor
r hhe
ea
at
t ssh
hi
ie
el
ld
ds
s.
.T
Th
he
e
a ab
bo
ov
ve
e mme
en
nt
ti
io
on
ne
ed
d mma
at
te
er
ri
ia
al
l cco
ou
ul
ld
d iig
gn
ni
it
te
e wwh
hi
il
le
e ddr
ri
iv
vi
in
ng
g.
.
W
WA
AR
RN
NI
IN
NG
G

139 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
Suggestion 6. Avoid short drives
The engine and the catalytic converter must reach its optimum
functioning temperature in order to effectively reduce consumption
and toxic gas emissions.
The fuel consumption of a cold engine of a normal vehicle right
after the start is about 30-40 liters per 100 km. After about one
kilometer the consumption decreases to 20 liters. After about
f fo
ou
ur
r
kilometers the engine has warmed up and the consumption is
normal. For this reason, it is important to avoid short drives and
heating the vehicle’s engine when the vehicle is not moving. Drive
on quickly!
The ambient temperature also counts. The illustration shows the
difference in consumption (l/100km) for the same distance (km) at
+20°C and –10°C. Your vehicle’s consumption is higher in the
summer than in the winter
⇒fig. 102.K
Suggestion 7. Check the tyre pressure
Make sure that the tyres have always adequate pressure. Even half
a bar less increases the level of fuel consumption by 5 percent. If
the pressure is not correct, the tyres wear out faster due to an
excessive deformation and overheating which, in turn, will
decrease the driving performance.
Always check the tyre pressure when the tyre is cold.
In addition, do not drive year round with winter tyres. They make
more noise and increase fuel consumption by 10 percent. Change
to summer tyres on time.
K
Suggestion 8. Avoid unnecessary weight
Apart from driving habits and periodic revisions of your vehicle,
there are other ways to reduce fuel consumption:
A Av
vo
oi
id
d uun
nn
ne
ec
ce
es
ss
sa
ar
ry
y wwe
ei
ig
gh
ht
t
Every kilogram increases fuel consumption. For this reason, it is
worth checking your boot to avoid unnecessary weight.
Frequently, the roof rack will stay on the roof even though it is no
longer needed. Due to greater air resistance, an unloaded roof
rack at a speed of 100-120 km/h increases the consumption by
approx. 12%.
K
5+20°C –10°C
15 25km
30
l/100km
B45-356PFig. 102

142Your vehicle and the environment
•In vehicles without air conditioning, the cooling system should
be reinforced if a towing device is fitted at a later stage.
Failure to do so will submit the engine to greater stress (steep
slopes, high temperatures, heavy towing loads, etc.) and result in
overheating of the engine. For more information, contact a
Technical Service Centre.
•When using a trailer on mountain routes you must bear in mind
that the tow loads given in the “Technical data” chapter are only
applicable for slopes of 10% to 12%. If you do not use the full tow
load you may drive up steeper slopes.
•The given trailer weights are only applicable for altitudes up
to 1000 m above sea level. As the engine output drops due to
the decreasing air density, the climbing ability must also be
reduced by 10% for each further 1000 m.
•Where possible make full use of the maximum permissible
drawbar weight on the ball of the towing bracket but do not exceed
it
⇒chapter “Technical Data”.
•While observing the permissible trailer and drawbar weight,
distribute the load in the trailer so that heavy objects are as near
as possible to the axle. The objects must also be secured so that
they cannot slip about.
•The tyre pressures on the towing vehicle must be adjusted for full
load conditions, and also check the pressures on the trailer.
•Headlight settings should be checked, with the trailer attached,
before beginning the journey and adjusted as necessary.
On vehicles with headlight beam control it is only necessary to turn
the knurled disc on the dash board in the appropriate direction.D Dr
ri
iv
vi
in
ng
g iin
ns
st
tr
ru
uc
ct
ti
io
on
ns
s
To obtain the best possible handling of vehicle and trailer, the
following should be noted:
• Try to avoid driving with an unladen vehicle and a loaded trailer.
If this cannot be avoided, only drive slowly to allow for the
unfavourable weight distribution.
• As driving stability of vehicle and trailer decreaseswhen the
speed increases do not drive at the maximum permissible top
speed in unfavourable road, weather or wind conditions –
particularly when going downhill.
In any case the speed must be reduced as soon as the trailer
shows the slightest sign of snaking. On no account try to stop the
snaking by accelerating.
• • FFo
or
r ssa
af
fe
et
ty
y rre
ea
as
so
on
ns
s oon
ne
e ssh
ho
ou
ul
ld
d nno
ot
t ddr
ri
iv
ve
e ffa
as
st
te
er
r tth
ha
an
n 880
0 kkm
m/
/h
h
( (5
50
0 mmp
ph
h)
).
. TTh
hi
is
s aal
ls
so
o aap
pp
pl
li
ie
es
s iin
n cco
ou
un
nt
tr
ri
ie
es
s wwh
he
er
re
e hhi
ig
gh
he
er
r ssp
pe
ee
ed
ds
s aar
re
e
p pe
er
rm
mi
it
tt
te
ed
d.
.
• Always brake in good time. If the trailer has an overrun brake,
apply the brakes gently at first then firmly. This will avoid the
jerking caused by the trailer wheels locking.
Change down before going down a steep hill so that the engine
can act as a brake.
• When a long climb in a low gear with extremely high engine revs
must be negotiated at exceptionally high ambient temperatures
the coolant temperature gauge must be observed. When the gauge
needle moves to the right end of the scale, the road speed must be
reduced immediately.
• The cooling effect of the radiator fan cannot be increased by
changing down, because the speed of the fan is not dependent on


151 Care and maintenance
Safety FirstControls and equipment Tips and Maintenance Technical Data
in the washing water it is advisable to protect the paint with a coat
of hard wax at least twice a year.
K
Polishing
Should only be done if paint has lost its shine and gloss cannot be
brought back with wax. If the polish used does not contain
preservative compounds, the paint must be waxed afterwards.
N No
ot
te
e
Matt painted and plastic parts should not be treated with polish or hard
wax.K
Paint damage
Small marks in the paint such as scratchesor stone damage
should be touched up immediately with paint before the metal
starts to rust.
However, should rust be found at any time it must be removed
thoroughly and then the area treated first with an anti-corrosion
primer and then the correct paint applied.
The number of the original vehicle paint is given on the data
sticker which is inside the boot in the spare wheel housing.
K
Windows
Remove snow and ice from windows and mirrors with a plastic
scraper only. To avoid scratches due to dirt on the glass, the
scraper should only be pushed in one direction and not moved to
and fro.
Traces of rubber, oil, wax
1), grease or silicone can be removed with
a window cleaning solution or a silicone remover.
The windows should also be cleaned on the inside at regular
intervals.
Do not dry the windows with the leather used for the paintwork
because traces of paint cleaner will cause streaks to appear on the
glass, which will hinder vision.
To avoid damaging the heating element wires in the rear window
do not put stickers over the wires on the inside.
K
Door, boot and window seals
The weatherstrips will remain flexible and last longer if they are
rubbed lightly with a rubber protective compound from time to
time. This will also stop the weatherstrips from freezing on in
winter.
K
Door lock cylinder
You should only use an appropriate spray, which has lubricating
and anti-corrosive qualities, to de-ice the lock cylinder.
K
1)This wax residue can only be removed with a special cleaner. Your Technical Service
Centre will provide you with more detailed information.

153 Care and maintenance
Safety FirstControls and equipment Tips and Maintenance Technical Data
Steel wheels
The wheels and the wheel trims should be cleaned thoroughly at
regular intervals when the vehicle is being washed. This will
prevent brake dust, dirt and road salt from accumulating on the
wheel. Persistent ingrained brake dust can be removed with an
industrial grime remover. Paint damage should be repaired before
rust can form.
K
Alloy wheels*
In order to maintain the smart appearance of alloy wheels for a
long period, regular care is necessary. In particular, salt and brake
pad dust must be washed off thoroughly at least every two weeks
otherwise the surface of the alloy will be damaged. After being
washed, the wheels should be treated with an acid-free cleaner for
alloy wheels. About every three months it is necessary to give
wheels a good rubbing with hard wax. Paint polish or other
abrasive solutions must not be used. If the protective paint coat
has been damaged, e.g. by stone impact, the damaged spots
should be dealt with as soon as possible.
Cleaning and anti-corrosion treatment of engine
compartment
The leaves, blossoms etc. which drop into the water box
(underneath the engine bonnet in front of the windscreen) should
be cleaned out occasionally. This will prevent the water drain holes
from becoming blocked and – on vehicles without a dust and
pollen filter – foreign bodies entering the vehicle interior via the
heating and ventilation system.
The engine compartment and the outside surface of the power unit
are given anti-corrosion treatment at the factory.
In the winter when the vehicle is being driven frequently on salted
roads, good anti-corrosion treatment is very important. For this
reason the entire engine compartment and the plenum chamber
should be thoroughly cleaned before and after the salting period
and then preserved so that the salt cannot have a damaging effect.
T Th
he
e iig
gn
ni
it
ti
io
on
n mmu
us
st
t bbe
e ssw
wi
it
tc
ch
he
ed
d oof
ff
f bbe
ef
fo
or
re
e wwa
as
sh
hi
in
ng
g tth
he
e een
ng
gi
in
ne
e.
.
D Do
o nno
ot
t ppo
oi
in
nt
t tth
he
e wwa
at
te
er
r jje
et
t ddi
ir
re
ec
ct
tl
ly
y aat
t tth
he
e hhe
ea
ad
dl
li
ig
gh
ht
ts
s tto
o aav
vo
oi
id
d
d da
am
ma
ag
ge
e.
.
P
Pl
le
ea
as
se
e nno
ot
te
e wwh
he
en
n ccl
le
ea
an
ni
in
ng
g tth
he
e wwh
he
ee
el
ls
s tth
ha
at
t dda
am
mp
pn
ne
es
ss
s,
, iic
ce
e aan
nd
d ggr
ri
it
t cca
an
n
h ha
av
ve
e aa nne
eg
ga
at
ti
iv
ve
e eef
ff
fe
ec
ct
t oon
n tth
he
e bbr
ra
ak
ki
in
ng
g ppo
ow
we
er
r.
.
K
W WA
AR
RN
NI
IN
NG
G
•B Be
ef
fo
or
re
e wwo
or
rk
ki
in
ng
g iin
n tth
he
e een
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t,
, rre
ea
ad
d tth
he
e nno
ot
te
es
s iin
n tth
he
e
" "E
En
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t"
" cch
ha
ap
pt
te
er
r.
.
•F
Fo
or
r ssa
af
fe
et
ty
y rre
ea
as
so
on
ns
s ppu
ul
ll
l oou
ut
t iig
gn
ni
it
ti
io
on
n kke
ey
y bbe
ef
fo
or
re
e rre
ea
ac
ch
hi
in
ng
g iin
nt
to
o tth
he
e wwa
at
te
er
r
b bo
ox
x.
. OOt
th
he
er
rw
wi
is
se
e iif
f tth
he
e wwi
in
nd
ds
sc
cr
re
ee
en
n wwi
ip
pe
er
rs
s aar
re
e ssw
wi
it
tc
ch
he
ed
d oon
n uun
ni
in
nt
te
en
nt
ti
io
on
na
al
ll
ly
y
t th
he
e mmo
ov
ve
em
me
en
nt
t oof
f tth
he
e wwi
ip
pe
er
r lli
in
nk
k cco
ou
ul
ld
d cca
au
us
se
e iin
nj
ju
ur
ry
y.
.
W
WA
AR
RN
NI
IN
NG
G


162Checking and refilling
C
Ca
au
ut
ti
io
on
n
• Only our G12+ (purple colour) should be used as an antifreeze additive.
Observe the notice on the container. The cooling liquid may be purchased in
Technical Services.
• The antifreeze additive G12+ can be mixed with other additives (G11 and
G12).
• The additive G12 (red colour) should never be mixed with G11.
K
Checking coolant level
The level can only be checked properly when the engine is not
running.
The coolant level must be between the
m ma
ax
xand m
mi
in
nmarks on the
expansion tank when engine is cold and can be slightly above the
m ma
ax
xmark when it is warm.K
Coolant losses
Coolant loss normally indicates leaks in the system. In this case
the cooling system should be checked by a Technical Service
Center without delay. It is not sufficient merely to add coolant.
In a sealed system losses can only occur if the boiling point of the
coolant is exceeded as a result of overheating, and coolant is
forced out of the system.
K
Topping up coolant
Switch engine off and let it cool down. Then cover expansion tank
cap with a cloth and turn cap carefully anti-clockwise and remove.
No other coolant may be used if
G G1
12
2+
+is not available. In this
case only water can be used and the correct mixture concentration
must be restored with the specified coolant additive (see previous
page) as soon as possible.
B6Y-0039KFig. 122
N Ne
ev
ve
er
r oop
pe
en
n tth
he
e bbo
on
nn
ne
et
t iif
f yyo
ou
u cca
an
n sse
ee
e sst
te
ea
am
m oor
r cco
oo
ol
la
an
nt
t lle
ea
av
vi
in
ng
g tth
he
e een
ng
gi
in
ne
e
c co
om
mp
pa
ar
rt
tm
me
en
nt
t –– RRi
is
sk
k oof
f ssc
ca
al
ld
di
in
ng
g!
! WWa
ai
it
t uun
nt
ti
il
l nno
o mmo
or
re
e sst
te
ea
am
m oor
r cco
oo
ol
la
an
nt
t cca
an
n
b be
e sse
ee
en
n.
.
W
WA
AR
RN
NI
IN
NG
G
D Do
o nno
ot
t rre
em
mo
ov
ve
e eex
xp
pa
an
ns
si
io
on
n tta
an
nk
k cca
ap
p wwh
he
en
n een
ng
gi
in
ne
e iis
s hho
ot
t –– dda
an
ng
ge
er
r oof
f
s sc
ca
al
ld
di
in
ng
g:
:
S Sy
ys
st
te
em
m iis
s uun
nd
de
er
r ppr
re
es
ss
su
ur
re
e.
.
W
WA
AR
RN
NI
IN
NG
G


172Servicing and replacing
Spark plugs
The spark plugs are renewed during the SEAT Inspection Service.
If the spark plugs have to be renewed between the Inspection
Services, the following should be noted:
• The spark plugs and ignition system have been matched to the
engine and as such contribute to reducing the levels of exhaust
pollutants. To avoid faulty operation, engine damage and even the
withdrawal of permission to circulate due to excessive emissions
values or non-suppressed spark plugs, only use the Genuine spark
plugs for the respective engine in question. It is particularlyimportant to examine the number of electrodes, the heat value and
if necessary, the anti-parasitic.
• For technical reasons, plugs may be modified at short notice. K
Dustand pollen filter*
The dust and pollen filter is located in the heating system. T Th
he
e
f fi
il
lt
te
er
r ssh
ho
ou
ul
ld
d bbe
e cch
ha
an
ng
ge
ed
d aac
cc
co
or
rd
di
in
ng
g tto
o tth
he
e tti
im
me
e iin
nt
te
er
rv
va
al
ls
s ggi
iv
ve
en
n iin
n
t th
he
e IIn
ns
sp
pe
ec
ct
ti
io
on
n aan
nd
d MMa
ai
in
nt
te
en
na
an
nc
ce
e PPl
la
an
n.
. IIf
f tth
he
e ppa
as
ss
sa
ag
ge
e oof
f aai
ir
r iis
s
h hi
ig
gh
hl
ly
y rre
es
st
tr
ri
ic
ct
te
ed
d,
, tth
he
e ffi
il
lt
te
er
r ssh
ho
ou
ul
ld
d bbe
e cch
ha
an
ng
ge
ed
d bbe
ef
fo
or
re
e.
.
You should have the filter replaced by a Technical Service Centre.
K