change time Seat Leon 5D 2010 MEDIA SYSTEM 2.2

Introduction
6IntroductionBefore using the unit for the first timeBefore using the unit for the first time, carry out the following steps. This will
enable you to use the unit safely and make full use of the functions it
provides•Observe the basic safety notes
’ ⇒ page 10.
•Familiarise yourself with the unit overview ⇒ page 8.•Restore factory settings (standard settings) in the system settings menu
⇒ page 87.•Use suitable data media for Media mode ⇒ page 29.Safety instructions
WARNING
Your attention may be distracted from the traffic if you use the radio and
navigation system while driving, resulting in accident.•You should always drive with due care and attention.•Select volume settings that allow you to easily hear signals from
outside the vehicle at all times (e.g. emergency service sirens).•If the volume is too high, you could damage your hearing. Even if the
volume is too loud for a short period only.
WARNING
The recommendations and traffic signs shown by the navigation system
may differ from the true traffic conditions.•Traffic signs and traffic regulations have priority over the recommenda-
tions and instructions given by the navigation system.•Adapt your speed and driving style to suit visibility, road, traffic and
weather conditions.WARNING
External devices that are placed loose in the vehicle or not properly secured
could be flung though the interior during a sudden driving or braking
manoeuvre, or in the event of an accident.•While the vehicle is in motion, always fasten or store external devices
securely outside the airbag deployment zones.•Arrange the connecting leads of external devices so that they do not
obstruct the driver.WARNING
The volume level may suddenly change when you switch audio source or
connect a new audio source.•Reduce the base volume before switching audio sources or connecting
a new audio source ⇒page 11.WARNING
Opening a CD player's housing may lead to injuries from invisible laser
radiation.
MediaSystem2.1_EN.book Seite 6 Donnerstag, 29. April 2010 4:18 16

Introduction9
Arrow buttons and always affect the currently active audio source
irrespective of the menu displayed on the screen.
− In all radio modes , press briefly (please observe the respective
display
­
) to change station or channel ⇒page 14.
− In Media mode , press briefly to change title or chapter, and hold down
to fast forward or rewind ⇒page 29.
CD slot ⇒page 29.
Touch scre en ⇒page 10.
CD eject button ⇒page 29.
Press Info to display additional information relating to the menu:
− Display or hide the radio text in Radio mode ⇒ page 21.
− Display additional title information (stored position) in Media mode
⇒ page 29.
− While navigating , to display current position of vehicle or
programmed destination ⇒page 47.
Press the back button to close menus and pop-up windows.
AUX-IN multimedia socket for connecting external audio sources
⇒ page 29.
Setting knob : the function depends on which mode is activated.
− In all radio modes , turn to manually change the station or channel
⇒ page 14.
− In Media mode , turn to manually change the title and press to stop
and start the scan function ⇒page 29.
− Tu r n to modify the map scale ⇒ page 63.
− During the route guidance , press to repeat a navigation instruction
⇒ page 63.
Function buttons : the current function is displayed on the screen via the
corresponding function button. ⇒page 10.
Memory card slot ⇒page 29.
A3
ƒ
„
A4A5A6
š
A7
º
A8
E
A9A10A11A12
MediaSystem2.1_EN.book Seite 9 Donnerstag, 29. April 2010 4:18 16

Introduction
10General operating informationIntroductionDue to changes to its settings, some aspects of the unit's operation may
differ from the descriptions given in this manual. For this reason, SEAT recom-
mends that you reset the unit to its factory settings the first time you use it
⇒ page 87.
Additional Information:•Safety notes
’ ⇒ page 6
•Unit overview ⇒page 8•Multifunction steering wheel, to change track or station ⇒Booklet
“Owner's Manual”, Section “Vehicle overview” Note
Lightly pressing the buttons or briefly pressing the touchscreen is sufficient
to operate the unit.
Note
Never press a button down for longer than 10 minutes. Otherwise the system
will interpret this as a malfunction ( button jammed).
Note
Due to country-specific legislation, certain functions cannot be selected on
the screen when the vehicle is travelling above a certain speed.
Note
Using a mobile telephone in the vehicle may cause noise from the vehicle
speakers.
Note
In some vehicles equipped with a parking distance warning system, the
volume of the current audio source is automatically lowered when reverse
gear is engaged.
Note
Restrictions on the use of devices using Bluetooth technology may be appli-
cable in some countries. Please ask your local authority for further
information.Switching on and offPress the rotary/push knob
D ⇒ page 8, fig. 1 briefly to manually switch
the unit on or off.
When the system is switched on, the sound source which was playing when
the unit was switched off will come on.
When the engine is off, the unit will automatically switch off after 30 minutes
(timeout).
Anti-theft code
The anti-theft code is stored in the vehicle once it has been entered (conven-
ience radio code). The anti-theft coding lock then only needs to be released
manually if the unit is installed in another vehicle. In such a case, a keypad
field and a prompt to enter the code will appear when the unit is switched on.
In this case, you should contact a SEAT dealer.
If the vehicle battery has been disconnected, switch on the ignition before re-
connecting the unit.
A1
MediaSystem2.1_EN.book Seite 10 Donnerstag, 29. April 2010 4:18 16

Introduction11
Adjusting the base volumeChanges to the volume are indicated by a “bar” on the screen. During this
time the unit cannot be operated.
At “0” the unit is muted (display:
) and the current media source is
stopped.
It is possible to preset certain volume settings and adjustments ⇒ page 87.
WARNING
Your attention may be distracted from the traffic if you use the radio and
navigation system while driving, resulting in accident.•You should always drive with due care and attention.•Select volume settings that allow you to easily hear signals from
outside the vehicle at all times (e.g. emergency service sirens).•If the volume is too high, you could damage your hearing. Even if the
volume is too loud for a short period only.Caution
If the volume is too high or the sound is distorted, the vehicle speakers may
be damaged.
Note
If the base volume has been turned up high to play an audio source (e.g. due
to very quiet audio output from an external audio source), lower the volume
again before switching audio source.Additional information and display optionsThe text displayed on the screen may vary depending on the settings and may
not match the illustrations shown here.
All displays appear only after the radio-navigation system has completed
start-up.
Depending on the vehicle, the changes to the air conditioning settings or the
texts relating to driver assistance systems fitted at the factory are displayed.
These displays disappear automatically when they are no longer required.
Function
Action
Increase the vol-
ume.
Turn the sound control knob
D ⇒ page 8, fig. 1 to the
right, or press the button on the multifunction steer-
ing wheel ⇒Booklet “Owner's Manual”.
Lower the vol-
ume.
Turn the volume control
D anti-clockwise
or press the button on the multifunction steering
wheel.

MediaSystem2.1_EN.book Seite 11 Donnerstag, 29. April 2010 4:18 16

Audio mode
28DAB programme tracking and switching from DAB to FM
The DAB and FM station should broadcast the corresponding station identi-
fier in order to run programme tracking in several frequencies.
When the DAB reception is poor, the unit tries to find and tune into the corre-
sponding DAB station in the FM band.
As long as the station is broadcast through the FM band, (FM) is displayed
behind the station name. When the station can be found again in DAB, the
(FM) display disappears.
If the reception of a DAB station is poor and it cannot be found on FM either,
the radio volume is muted.
The DAB programme tracking function can be switched off if you do not wish
to change stations automatically, as the loss of signal is for a short time only,
for example, when driving though a tunnel.Function button: Result
: the incoming DAB messages are played with the
DAB radio mode on. If there is no FM station temporarily available and the
TP function is on, the DAB traffic reports are played in any operating mode
as TP reports ⇒page 21.
: tracking of activated programmes. To switch off, untick the
check box.
: The unit may be set to switch to the FM fre-
quency band when required for automatic station tracking.
’ DAB announcements’DAB tracking’ Automatic switch DAB-FM
MediaSystem2.1_EN.book Seite 28 Donnerstag, 29. April 2010 4:18 16

Audio mode29
Media modeIntroduction“Media sources ” are audio sources containing audio files on various different
data media (e.g. CD, memory card, exte rnal MP3 player). These audio files
can be played by the radio and navigation system from its corresponding
drives or audio input sockets (internal CD changer, memory card slot, AUX-IN
multimedia socket etc.).
The supported file formats listed are collectively referred to below as “audio
files”. A CD containing audio files of these types is referred to as an “audio
data CD”.
Additional Information:•Safety notes
’ ⇒ page 6
•Unit overview ⇒ page 8•Multimedia interface ⇒ page 42WARNING
Inserting a data medium while you are driving could distract you from the
road and result in accident.Media source and audio file requirementsFactory-fitted CD players conform to safety class 1 according to
DIN IEC 76 (CO) 6/ VDE 0837.
The unit only accepts 12-cm standard CDs and memory cards with the dimen-
sions 32 mm x 24 mm x 2.1 mm or 1.4 mm.
Media source
Requirements for playing in the unit
IAudio CDs with CD Digital
Audio logo
.
- CD Digital Audio specification.
ICD-ROM, CD-R and CD-RW
audio data CDs up to max.
700 MB (megabytes) compli-
ant with ISO 9660 or in the
Joliet file system.KSD and MMC memory
cards up to max. 2 GB (giga-
bytes) and SDHC memory
cards up to max. 32 GB.
- MP3 files (.mp3) with bit rates of between
48 and 320 kbit/s or with variable bit rate.
- WMA files (.wma) up to 9.2 mono/stereo
without copy protection.
- Playlists in the formats PLS, M3U and WPL.
- File names and paths no longer than 256
characters.
- Folder structures with a maximum of eight
levels.
- Audio data CDs with max. 50 folders and
max. 500 files.
- Memory cards with max. 5000 folders and
max. 15000 files with max. 6000 files per
folder.

Playing audio files via Blue-
tooth
®a).
a)Bluetooth
® is a registered trademark of Bluetooth SIG, Inc.
- The external audio source must be compat-
ible with the Bluetooth A2DP profile.
AUX. External audio source.
– Audio output is possible with a 3.5 mm
jack connector ⇒page 8, fig. 1 .
MDI. External data medium.
- Compatible with MEDIA-IN multimedia
interface ⇒page 42.
AUX2 . Additional external
source
- Depending on the vehicle equipment, this
source can be used to play audio from an
external player connected to a Rear Seat
Entertainment system (only if the vehicle
does not have MDI).
A9
MediaSystem2.1_EN.book Seite 29 Donnerstag, 29. April 2010 4:18 16

Audio mode33
Note
If you insert a number of different CDs and receive the message CD drive error
every time, contact a qualified workshop.Inserting and removing memory cardsOnly supported audio files are displayed and played in the MEDIA main
menu. Other file types will be ignored.
A compatible memory card is indicated by SD card or
K on the screen.
Inserting the memory card
If a memory card cannot be inserted, make sure it is positioned correctly and
is compatible with the unit.
•Insert a compatible memory card into the memory card slot ⇒page 8,
fig. 1 with the cut-off corner first and facing upwards until the card clicks
into place.•Playback starts automatically if supported audio files are stored on the
memory card.
Manually removing the memory card•Press the inserted memory card. The memory card “jumps” to the eject
position.•Remove the memory card.
Memory card cannot be read
If legible audio files have not been stored on a memory card, the unit will not
change to memory card mode after it is loaded.
If the unit cannot read from the memory card at all, you will also be informed
by a pop-up window.•Press the function button. If an illegible memory card or an card which does not contain audio files is
inserted, the function button for the
Media selection menu remains inac-
tive ⇒page 37.
The memory card must be removed manually.
External audio source connected to the AUX-IN multimedia socketThe AUX-IN multimedia socket ⇒page 8, fig. 1 can only be used with a
3.5 mm jack plug.
The external audio source connected to it is played over the vehicle speakers
and cannot be controlled via the radio-navigation system.
An external audio source connected to the socket is indicated by AUX on the
screen.
A12
OK
K
Fig. 27 External audio
source connected to AUX
IN multimedia socket.
A9
MediaSystem2.1_EN.book Seite 33 Donnerstag, 29. April 2010 4:18 16

Audio mode
44Connecting and disconnecting an external data medium (MDI)•Connect the appropriate adapter to the MEDIA-IN multimedia interface
⇒ page 42.•Connect the external data medium to the MEDIA-IN multimedia interface
via the adapter.•I f n e ce s sa r y, s wi tch o n t h e e x t e r na l d a ta m e d i u m o r s e l e c t t h e a p p r o p r i a t e
data mode.
Even though the display may indicate otherwise, the external data medium
may be disconnected from the MEDIA-IN multimedia interface at any time
without data loss.
Connecting or disconnecting an external data medium (MDI) - Altea, Altea XL,
Altea Freetrack, Leon
– Connecting a mass storage device or player with a USB connection
Connect the device to the USB connector of the MEDIA-IN interface.
If necessary, start playback in the external device.
– Connecting an iPod or iPhone in order to control it from the radio and
navigation system
Connect the iPod or iPhone to the MEDIA-IN interface using the cable or
special iPod adapter provided by SEAT.
– Connecting an external device to the AUX input of the MEDIA-IN interface
Connect the device to the AUX input of the MEDIA-IN interface with the
right cable.
Even though the display may indicate otherwise, the external data medium
may be disconnected from the MEDIA-IN multimedia interface at any time
without data loss.
Control through the radio and navigation system
An external data medium correctly connected to the MEDIA-IN multimedia
interface can be controlled through the radio and navigation system. Depending on the unit, when an external data medium is connected and
switched on, it is necessary to change to the radio and navigation system
manually for playback.
•Open the
MEDIA main menu.•Press the unit button to open the Media selection menu .•Press the function button to start or resume playback from the
external data medium.
Further operation of the external data medium (changing track, selecting
tracks and playback modes) is described in the appropriate chapters of this
manual ⇒page 29.
If the selected media source is disconnected from the MEDIA-IN multimedia
interface while being played, the radio and navigation system will remain in
MDI mode. Another audio source must be selected manually.
Special features. ALTEA and LEON models
Depending on the vehicle equipment, from the radio and navigation unit and
via the MEDIA-IN interface, the user can:•play and control audio files from a mass storage device or MP3 player with
USB, iPod or iPhone connection.•play audio from an external player connected to the AUX input of the
Media-In Interface•play audio from an external player connected to the AUX input of the Rear
Seat Entertainment system (if fitted in the vehicle)
Sometimes the additional auxiliary input of the Media-In interface must be
activated in order to use the MDI media source in the media selector.
Activation:•ticking the Activate AUX2 input check box in the Media Setup Menu or,•this option can also be activated using the function button in the pop-up
window which appears when you try to go to the MEDIA main menu when
there is no media source connected or activated.
MEDIAMDI
MediaSystem2.1_EN.book Seite 44 Donnerstag, 29. April 2010 4:18 16

Navigation47
NavigationIntroduction to navigationIntroductionGeneral information
The current vehicle position is determined by means of the GPS system
(Global Positioning System). Sensors in the vehicle measure distances
driven. The measurements are adapted using the detailed information given
in the navigation data medium ma ps and according to the programmed
traffic management. Where applicable, TMC traffic reports are included in the
calculation of routes ⇒ page 70. The navigation system uses these data to
determine an optimal route to the destination.
The destination is defined by entering an address or a point of interest, e.g.
apetrol station or hotel.
Navigation announcements and visual guidance on the navigation unit and
the instrument panel direct you to your destination ⇒page 63.
Depending on the country, some radio-navigation system functions can no
longer be selected when the vehicle is travelling above a certain speed. This
is not a malfunction, but simply a legal requirement.
Navigation data
In normal circumstances, all the necessary navigation data is already stored
in the navigator. A memory card containing the navigation data can be
obtained from an Authorised Service to update this information ⇒page 48.
Additional Information:•Safety notes
’ ⇒ page 6
•Unit overview ⇒ page 8•Entering a destination ⇒page 52
•Destination memory ⇒page 58•Route guidance ⇒ page 63Note
Dirty or damaged navigation data media may lead to problems when copying
navigation information or even in the navigation itself. Store unused data
media in a suitable container or in the original box to protect them from
mechanical damage, heat, humidity or direct sunlight.Limitations of the navigation functionPossible errors in navigation
If the navigation system is not able to receive data from the GPS satellites
(dense vegetation, underground garage), it is still possible to navigate using
the vehicle sensory analysis.
In areas that are not or only partially digitised on the data medium
(e.g. insufficient definition of one-way streets and road categories), the navi-
gation system will still attempt to provide route guidance.
If navigation data are unavailable or incomplete, the navigation system may
be unable to determine the exact vehicle position. As a result, the navigation
may not be as exact as usual.
Navigation area and age of navigation data
The accuracy of the data (small villages, streets and house numbers)
depends on the respective version for the country.
Roads and streets are subject to constant change (e.g. new roads, changes to
street names and house numbers). After some time, navigation data will no
MediaSystem2.1_EN.book Seite 47 Donnerstag, 29. April 2010 4:18 16

Navigation
64changed while route guidance is in progress. The route will then be recalcu-
lated.•Press the unit button in one of the navigation menus.•In the Navigation setup menu , press the function button
⇒ page 63, fig. 63.•Select or deselect an option by ticking or clearing the appropriate
checkbox ⇒page 63, fig. 64 .
Defining route criteria •In the Route options setup menu , press the function button.•Press the desired settings to select them in the pop-up window.
Dynamic route
If dynamic route guidance is activated, TMC traffic reports will be taken into
account in the route calculation ⇒page 70.
Excluding types of route in the calculation
The function buttons , etc. define whether or not these
types of road may be included in the route calculation.
Even when excluded, these types of route will still be included in the route
calculation if no practical alternative route exists. For example, if it is impos-
sible to reach an island without using the ferry. For the calculation of very long
routes, it is not possible to avoid motorways.
Navigation announcementsWhen the route has been calculated, the first announcement is given. Up to
three navigation announcements are given before a turn, e.g. within a town
“Prepare to turn left”, “Turn left after 300 metres” and “Now turn left”.•Press the setting knob ⇒page 8, fig. 1 to hear the last navigation
announcement again.
The distances that are announced depend on the type of road and the speed
at which you are driving. On motorways, the first announcement is given
roughly 2,000 m before an exit.
For example, the following announcements may be heard on multi-lane high-
ways or roads that divide, and at roundabouts: “Take the second exit at the
roundabout!”.
When you arrive at your destination, the following announcement is heard:
“You have reached the destination”.
During dynamic route guidance, you receive information about reported
traffic congestion on the route. If the route is recalculated due to traffic
congestion, you will be advised accordingly ⇒page 70.
Announcement settings.
Navigation announcements are played at the preset volume.
The volume of an announcement can be changed with the volume control
D.
All following announcements will then be made at this volume.
The volume of navigation announcements can be preset or switched off in the
Navigation setup menu ⇒ page 73 or in the volume settings ⇒page 88.
Route criteria
MeaningFastest route to the destination, even if it means driv-
ing further.This function aims to find an equilibrium between the
shortest time and the shortest route.Shortest route to the destination, even if it results in a
longer travelling time. The navigation route may
include unusual route sections, e.g. dirt roads.
SETUP
Route optionsRoute criteria
FastEconomicalShort
˜Avoid motorways
A10
MediaSystem2.1_EN.book Seite 64 Donnerstag, 29. April 2010 4:18 16