display SKODA YETI 2015 1.G / 5L User Guide

Fuel gaugeFig. 25
Fuel gauge
Read and observe on page 28 first.
The display » Fig. 25 provides information on the fuel supply in the container.
The display only works if the ignition is switched on.
The fuel tank has a capacity of about 55 litres or 60 litres 1)
.
When the fuel level reaches the reserve area
A
» Fig. 25 , the warning light

» page 37 illuminates.
WARNINGFor the vehicle systems to function correctly, and thus for safe driving,
there must be sufficient fuel in the tank. Never drain the fuel tank com-
pletely – risk of accident!
CAUTION
Never drive until the fuel tank is completely empty! The irregular supply of fuel
can cause misfiring. This can result in considerable damage to parts of the en-
gine and the exhaust system.
Note
After filling up, it can occur that during dynamic driving (e.g. numerous curves,
braking, driving downhill and climbing a steep hill) the fuel gauge indicates ap-
prox. a fraction less. When stopping or during less dynamic driving, the fuel
gauge displays the correct fuel level again. This is not a fault.Counter for distance drivenFig. 26
Display: MAXI DOT display / Seg-
ment Display
Read and observe on page 28 first.
Display » Fig. 26
Counter for the distance travelled since the last reset (trip)
Odometer
Reset counter for distance travelled (trip)
›
Press and hold the
7
» Fig. 22 on page 28 button.
Note
If the second speedometer display is enabled on vehicles with a segment dis-
play, this speed will be shown instead of the odometer during the journey.
Setting the time
Read and observe
on page 28 first.
Use buttons
3
and
7
to set the clock » Fig. 22 on page 28 .
The choice to change the display (hours or minutes).
The change of the displayed value.
In vehicles equipped with the MAXI DOT display, it is also possible to set the
Time
in the Time menu » page 47, Menu item
Settings
.
AB371)
Valid for Yeti 4x4.
30Using the system

Display of the second speedometerRead and observe
on page 28 first.
The display can show the current speed in mph 1)
.
This feature is provided for driving in countries with different speed units.
MAXI DOT display
The display of the second speedometer can be set in the
Alt. speed dis.
menu
item » page 47 , Menu item
Settings
.
Segment display
›
Press key
3
» Fig. 22 on page 28 repeatedly, until the odometer display
flashes » page 30 .
›
Press the
7
key while the display flashes.
The second speedometer is displayed instead of the odometer.
The display of the second speedometer is switched off in the same manner as
it is switched on.
Auto Check Control
Read and observe
on page 28 first.
Vehicle condition
Certain functions of vehicle systems are checked continuously when the igni- tion is switched on.
Some error messages and other information are displayed in the MAXI DOT
display. The messages are displayed simultaneously with the warning lights in
the MAXI DOT display or with the warning lights in the instrument cluster
» page 32 , Warning lights .
The menu item
Vehicle status
is shown in the main menu of the MAXI DOT dis-
play whenever at least one fault message exists. After selecting this menu,
the first of the error messages is displayed.
Several error messages are shown on the display under the message e.g. 1/3.
This indicates that the first of a total of three error messages is being dis-
played.
Warning lights in the MAXI DOT displayEngine oil pressure too low» page 34Check engine oil level
Engine oil sensor defective» page 169Engine-speed limitation» page 31Water in fuel filter (diesel engine).» page 31Automatic gearbox DSG overheated» page 31AdBlue ®
level too low» page 31
 Engine-speed limitation
The information about the maximum permissible engine speed is displayed to-
gether with this warning light.
Do not exceed the indicated maximum engine speed!
Have the vehicle checked by a specialist garage.
 Water in the fuel filter (diesel engine)
The fuel filter with water separator, filters out dirt and water from the fuel.
If too much water is present in the separator, the following information ap-
pears on the instrument cluster display.

 Water in fuel filter. Owner´s manual!FUEL FILTER SEE MANUAL
Seek help from a specialist garage.
 Automatic gearbox DSG overheated
Gearbox overheated. Stop! Owner´s manual!
▶

Do not continue to drive! Stop the vehicle and turn off the engine.
You can continue your journey as soon as the warning light disappears.
 AdBlue ®
level too low
The warning light  is only shown in the MAXI DOTdisplay. 
1)
For models with the speedometer in mph, the second speedometer is displayed in km/h.
31Instruments and Indicator Lights


AdBlue (DEF) refill! Range: ...ADBLUE RANGE …
The range in the display indicates the distance that can be driven with the re-
maining AdBlue ®
left in the tank.
Refill AdBlue ®
» page 164 .

 AdBlue (DEF) refill! No engine start in …ADBLUE NO START IN …
The range in the display indicates the distance to travel, after which no engine
restart is possible, as long as no AdBlue ®
is added.
Refill AdBlue ®
» page 164 .

 AdBlue (DEF) refill! No engine start possible.ADBLUE NO RESTART
It is no longer possible to start the engine.
Refill AdBlue ®
» page 164 .
WARNINGIf you have to stop for technical reasons, then park the vehicle at a safe
distance from the traffic, switch off the engine and switch on the hazard
warning light system » page 68. Place the warning triangle at the prescri-
bed distance.
Note
■ If the MAXI DOT display shows warning messages, these messages must be
confirmed in order to access the main menu » page 41, Operation .■
As long as the operational faults are not rectified, the warning lights are al-
ways indicated again. After they are displayed for the first time, the warning
lights continue to be indicated without any extra messages for the driver.
Warning lights
 Introduction
This chapter contains information on the following subjects:
 Handbrake
33
 Brake system
33
 Seat belt warning light
33 Alternator33 Door open33

Coolant
33
 Boot lid
34
 
Power steering/steering lock (KESSY system)
34

34

Traction Control System (ASR)
35
 Electronic Stability Control (ESC)
35
 Traction control (TCS) is deactivated
35
 Antilock brake system (ABS)
36
 Rear fog light
36
 Lamp failure
36
 Xenon headlights (AFS)
36
 Exhaust inspection system
36
 Glow plug system (diesel engine)
36
 Engine performance check (petrol engine)
37
 Diesel particulate filter (diesel engine)
37
 Fuel reserve
37
 Airbag system
37
 Tyre pressure
38
 Windscreen washer fluid level
38

 Turn signal system
38
 Fog lights
39
 Cruise control system
39
 Brake pedal (automatic gearbox)
39
 OFF ROADmode
39
 Main beam
39
The warning lights indicate certain functions or faults.
Some warning lights can be accompanied by acoustic signals and messages in
the display of the instrument cluster.
After switching on the ignition, some warning lights light up briefly as a func-
tion test.
If the tested systems are OK, the corresponding warning lights go out a few
seconds after switching on the ignition or after starting the engine. 
32Using the system

WARNING■Ignoring illuminated warning lights and related messages or instructions
in the display of the instrument cluster may lead to serious personal injury
or damage to the vehicle.■
If you have to stop for technical reasons, then park the vehicle at a safe
distance from the traffic, switch off the engine and switch on the hazard
warning light system » page 68. Place the warning triangle at the prescri-
bed distance.
■
The engine compartment of your car is a hazardous area. The following
warning instructions must be followed at all times when working in the en-
gine compartment » page 165, Engine compartment .
 Handbrake
Read and observe
on page 33 first.
 illuminates – the hand brake is applied.
An acoustic signal will sound if you drive the vehicle above 6 km/h for at least
3 seconds while the handbrake is applied.
Release parking brake!
 Brake system
Read and observe
on page 33 first.
 illuminates – the brake fluid level in the braking system is too low.
Brake fluid: Owner's Manual!›
Stop the vehicle, switch off the engine, and check the level of the brake fluid
» page 171 .
WARNING■
If the warning light  lights up together with the warning light 
» page 36 ,  Antilock brake system (ABS) ,  stop driving! Seek help from
a specialist garage.■
A fault to the ABS system or the braking system can increase the vehi-
cle's braking distance – risk of accident!
 Seat belt warning light
Read and observe
on page 33 first.
 illuminates - the driver or front passenger has not fastened their seat belt.
The indicator light 
goes off after the respective seat belt is fastened.
At a speed of more than approximately 20 km/h the warning light 
flashes
and an audible warning sounds at a time.
If the seat belt is not fastened by the driver or front passenger during the next
approx. 2 seconds, the warning signal is deactivated and the warning light 
lights up permanently.
 Alternator
Read and observe
on page 33 first.
 illuminates – the battery is not being charged whilst the engine is running.
Seek help from a specialist garage.
CAUTION
If in addition to the symbol  the symbol  » page 33 lights up while driving,
 stop driving - risk of engine damage! Switch off the engine and seek assis-
tance from a specialist garage.
 Door open
Read and observe
on page 33 first.
 illuminates - one or more doors are open.
On vehicles with MAXI DOT display, this indicator is replaced by a vehicle icon
on the display » page 40 .
 Coolant
Read and observe
on page 33 first.
 illuminates or flashes – the coolant temperature is too high or the coolant
level is too low.
Check coolant! Owner´s manual!

33Instruments and Indicator Lights

›Stop the vehicle, switch off the engine, check the level of the coolant, and
refill the coolant if necessary.
If the coolant level is within the specified range and the warning light 
illumi-
nated again after ignition on, then there may be a malfunction of the cooling
fan.›
Switch off the ignition.
›
Check the fuse for the radiator fan, replace if necessary.
If the coolant level and the fan fuse are OK and the warning light 
illuminates
again after ignition on 
do not continue to drive!
Seek help from a specialist garage.
WARNING■ Carefully open the coolant expansion bottle. If the engine is hot, the cool-
ing system is pressurized - risk of scalding! It is therefore best to allow the
engine to cool down before removing the cap.■
Do not touch the radiator fan. The radiator fan may switch itself on auto-
matically even if the ignition is off - risk of injury!
 Boot lid
Read and observe
on page 33 first.
 illuminates - the boot lid is open.
On vehicles with MAXI DOT display, this indicator is replaced by a vehicle icon
on the display » page 40 .
  Power steering/steering lock (KESSY system)
Read and observe
on page 33 first.
Fault in the power steering
 illuminates – this indicates a complete failure of the power steering and the
steering assist has failed (significantly higher steering forces).
 illuminates – this indicates a partial failure of the power steering and the
steering forces can be greater.
Seek help from a specialist garage.
Steering column lock not unlocked (System KESSY)  flashes - for vehicles with the KESSY system, the steering lock is not re-
leased.
▶ Move the steering wheel slightly back and forth, thereby facilitating unlock-
ing the steering lock.
If the steering does also not unlock then, the help of a specialist garage is re-
quired.
Steering lock defect (KESSY system)
An audible signal sounds as a warning. flashesSteering column lock faulty.
Park the vehicle,
stop driving
. After switching off the ignition, it is then no
longer possible to lock the steering, to activate the electrical components (e.g.
radio, navigation system), to switch on the ignition again and to start the en-
gine. Seek help from a specialist garage.
 flashesSteering column lock: Workshop!
Seek help from a specialist garage.
Disconnecting the vehicle battery
If the vehicle's battery has been disconnected and reconnected, the indicator
light  comes on after switching on the ignition.
The warning light should go out after driving a short distance.
If, after the motor is restarted and a short drive, the indicator light does not go
out, there is a system error.
Seek help from a specialist garage.
 
Read and observe on page 33 first.
Low oil pressure
 flashesOil pressure: Engine off! Owner´s manual!
▶
Stop the vehicle, switch off the engine, and check the engine oil level.
If the warning light flashes ,

do not drive an further! even if the oil level is
correct! Also do not leave the engine running at an idling speed.
Seek help from a specialist garage. 
34Using the system

Traction control (ASR) is deactivated.
 Antilock brake system (ABS)Read and observe
on page 33 first.
 illuminates – there is an ABS fault.
Error: ABS
The vehicle will only be braked by the normal brake system without the ABS.
Seek help from a specialist garage.
In the event of an ABS fault, the other braking and stabilization systems are
turned off » page 127, Braking and stabilisation systems .
WARNING■
If the warning light  lights up together with the warning light 
» page 33 ,  stop driving! Seek help from a specialist garage.■
A fault to the ABS system or the braking system can increase the vehi-
cle's braking distance – risk of accident!
 Rear fog light
Read and observe
on page 33 first.
 illuminates – the rear fog light is switched on.
 Lamp failure
Read and observe
on page 33 first.
 illuminates – one of the vehicle's exterior lights is defective. A message will
appear concerning the affected lamp.
 illuminates within a few seconds after switching on the ignition or when a
light with a faulty bulb is switched on.
Example of a message in the MAXI DOT display.
INFORMATION Check front right low beam! Xenon headlights (AFS)
Read and observe
on page 33 first.
 flashes for 1 minute while driving or after the ignition is switched on - there
is a fault in the xenon headlight.
The following message is shown in the MAXI DOT display.
No cornering lighting (AFS) function. Owner´s manual!
Note
With the Xenon headlight “tourist light” (travel mode) activated, the warning
light  flashes after switching on the ignition for 10 seconds.
 Exhaust inspection system
Read and observe
on page 33 first.
 illuminates – there is a fault in the emission control system. The system al-
lows operation emergency mode - there may be a noticeable reduction in en-
gine performance.
Seek help from a specialist garage.
 Glow plug system (diesel engine)
Read and observe
on page 33 first.
The warning light 
lights up after the ignition has been switched on. Once
the light has gone out, the engine can be started immediately.
 flashes – there is a fault in the engine management system. The system al-
lows operation emergency mode - there may be a noticeable reduction in en-
gine performance.
There is a fault in the glow plug system if the warning light  does not come
on or illuminates continuously.
Seek help from a specialist garage.
36Using the system

 Engine performance check (petrol engine)Read and observe
on page 33 first.
 illuminates – there is a fault in the engine management system. The system
allows operation emergency mode - there may be a noticeable reduction in en-
gine performance.
Seek help from a specialist garage.
 Diesel particulate filter (diesel engine)
Read and observe
on page 33 first.
The diesel particulate filter separates the soot particles from the exhaust. The
soot particles collect in the diesel particulate filter where they are burnt on a
regular basis.
 Illuminates – the filter is clogged with soot.
To clean the filter, and where traffic conditions permit »
, drive as follows for
at least 15 minutes or until the indicator light  goes out.
4th or 5th gear engaged (automatic gearbox: position S).
Vehicle speed at least 70 km/h.
Engine speed between 1800-2500 rpm.
If the filter is properly cleaned, the warning light  extinguishes.
If the filter is not properly cleaned, the warning light  does not go out and
the warning light  begins to flash.
Diesel Particulate Filter: Owner´s manual!
The system allows the vehicle to run in emergency mode. After switching the
ignition off and on again the indicator light, the warning light  also illumi-
nates.
Seek help from a specialist garage.
WARNING■ Always adjust the speed and driving style to the actual weather, road, ter-
rain and traffic conditions.■
The diesel particulate filter reaches very high temperatures - there is a
fire hazard and serious injury could be caused. Therefore, never stop the
vehicle at places where the underside of your vehicle can come into contact
with flammable materials such as dry grass, undergrowth, leaves, spilled
fuel or such like.
CAUTION
■ As long as the warning light  illuminates, one must take into account an
increased fuel consumption and a power reduction of the engine.■
Using diesel fuel with an increased sulphur content can considerably reduce
the life of the diesel particle filter. A ŠKODA partner will be able to tell you
which countries use diesel fuel with a high sulphur content.
Note
■ To assist the combustion process of the soot particles in the filter, we recom-
mend that regularly driving short distances be avoided.■
If the engine is turned off during the filter cleaning process or shortly after-
wards, the cooling fan may turn on automatically for a few minutes.
 Fuel reserve
Read and observe
on page 33 first.
 illuminates – the fuel level in the fuel tank is at the reserve level (approxi-
mately 9 litres).
An audible signal sounds as a warning.
Please refuel. Range: ... km
Note
The text in the display goes out only after refuelling and driving a short dis-
tance.
 Airbag system
Read and observe
on page 33 first.
System fault
 illuminates - there is a fault in the airbag system. 
37Instruments and Indicator Lights

 Fog lightsRead and observe
on page 33 first.
 illuminates – the fog lights are switched on.
 Cruise control system
Read and observe
on page 33 first.
 illuminates – the vehicle speed is regulated by the cruise control.
 Brake pedal (automatic gearbox)
Read and observe
on page 33 first.
 illuminates – apply the brake.
 OFF ROADmode
Read and observe
on page 33 first.
 illuminates – the conditions for the engagement of OFF ROADmode are met.
 flashes – the hill descent assistant is engaged at the moment.
For more information about OFF ROAD mode » page 129, OFF ROAD-mode .
 Main beam
Read and observe
on page 33 first.
 illuminates – the main beam or the headlight flasher is switched on.
Information system
Driver information system

Introduction
This chapter contains information on the following subjects:
Display a low temperature
39
Door, boot or engine compartment warning
40
Overspeed warning at 120 km/h
40
Gear recommendation
40
Depending on the vehicle's equipment, the information system vie the display
of the instrument cluster provides the following information.
▶ Data relating to the multi-function display (MFD) » page 41.
▶ Data relating to the Maxi DOT display » page 43.
▶ Service interval display » page 48.
▶ Auto Check Control » page 31.
▶ Selector lever positions for an automatic gearbox » page 122.
WARNINGConcentrate fully at all times on your driving! As the driver, you are fully re-
sponsible for the operation of your vehicle.
Display a low temperature
Read and observe
on page 39 first.
If the outside temperature drops below +4 °C while driving, the warning light 
(low temperature warning) illuminates and an audible signal sounds.
If the outside temperature is below +4 °C when the ignition is switched on, the
following warning light appears in the display .
WARNINGEven at temperatures of around +4 °C, black ice may still be on the road
surface! You should therefore not only rely on the outside temperature dis- play for accurate information as to whether there is ice on the road.39Information system

Door, boot or engine compartment warningRead and observe
on page 39 first.
Vehicles with a MAXI DOT display
If at least one door, the boot or bonnet is open, the display indicates the rele-
vant open door, boot or bonnet vehicle icon.
Vehicles with a segment display
If at least one door or the boot lid is open, the 
warning light in the instru-
ment cluster lights up » page 33.
If the boot lid is open, the 
warning light in the instrument cluster lights up
» page 34 .
An acoustic signal will also sound if you drive the vehicle above 6 km/h when a
door is open.
Overspeed warning at 120 km/h
Read and observe
on page 39 first.
This function only applies to certain countries.
An audible warning signal will sound when the vehicle speed exceeds 120
km/h. The audible warning signal is switched off when the vehicle speed falls
below 120 km/h.
Gear recommendationFig. 27
Information on the selected gear / Gear recommendation
Read and observe
on page 39 first.
A suitable gear is engaged, if necessary, a recommendation to shift to high or
lower gear is displayed.
A suitably engaged gear helps to reduce the fuel consumption and assist the
service life and reliability of the engine.
For vehicles with automatic transmission the recommended gear will be
shown provided the mode for manual switching (Tiptronic) is selected.
Recommended gear
MAXI DOT display
Optimal gear engaged
Recommended gear
Segment display Optimal gear engaged
Recommended gear
Gear recommendation - MAXI DOT display
Besides showing the engaged gear, the arrow icon  and the recommended
gear are displayed.
For instance, if 

 appears in this display, this means it is recommended that
you shift from 3rd into 4th gear. 
40Using the system

Gear recommendation - segment display
The recommended 1)
gear and the arrow icon is displayed.
▶  - Recommends that you change up to a higher gear
▶  - Recommends that you change down to a lower gear
If the display shows for example 

in vehicles with a manual gearbox, this
means it is better to switch from a lower gear to the fourth gear.
If for example 

is shown in the display in vehicles with an automatic gearbox
which is in manual switching mode (Tiptronic), it is better to switch from the
fourth gear to a higher gear.WARNINGThe driver is always responsible for selecting the correct gear in different
driving situations, such as overtaking.
Multifunction display (MFD)
 Introduction
This chapter contains information on the following subjects:
Operation
41
Information overview
42
Warning when exceeding the set speed
42
Memory
43
The driving data is displayed on the multifunction display.
The multifunction display only operates if the ignition is switched on. After the ignition is switched on, the function that was last selected before switching
off the ignition is displayed.
For vehicles with a MAXI DOT display, the menu item
MFD
must be selected and
confirmed in the main menu » page 43, MAXI DOT display .
On vehicles with a MAXI DOT display, there is an option to fade out some of
the information » page 47, Menu item
Settings
.
WARNINGConcentrate fully at all times on your driving! As the driver, you are fully re-
sponsible for the operation of your vehicle.
Note
If the display of the second speed is activated in mph, the current speed is not
indicated in km/h on the display.
Operation
Fig. 28
Buttons/dial: on the operating lever/the multifunction steering
wheel
Read and observe
on page 41 first.
The selection as well as the settings of the data values can be operated with
the buttons on the operating lever as well as on the multi-function steering
wheel » Fig. 28 .
Description of the operation
Button / dialActionOperationABriefly press at the top or downSelect data / set data valuesBPress brieflyView information / confirm specifica- tion 1)
With vehicles that have an automatic gearbox and in the manual switching mode (Tiptronic) the
current-
ly engaged gear is shown.
41Information system